Dual Gate Operators - Maximum Controls MAX MEGATRON 1400HP Installation And Owner's Manual

dual Gate Operators

The gates must be properly installed and work freely in both directions prior to the installation of the dual gate operators.
See "Gate Operator Position" on page 6 for operator positions and previous page for arm height.
Secure EACH gate
operator to concrete pad
with six (6) 1/2"x 3" (min)
sleeve anchors.
Secondary
Operator
NO Matrix 1
1/2
Battery Voltage MAX BC-7
E 1/2 F Battery Module
ON/OFF Replace TEST Battery IN
Battery Battery Battery Error
6" Above
Ground
Conduit
Check local building codes in your area for
Input
depth of concrete before installation.
Power
Concrete Depth Note: The heavier the gates, the deeper the concrete
pads should be. At least two feet recommended for heavier gates.
Each entrapment protection device MUST be connected to corresponding gate operator.
Dual Gates CLOSING direction Thru-Beam Photocell ONLY:
See separate wiring instruction sheet.
Reflector
Illustrations not to scale
OPENING/CLOSING
direction Mini
Sensing Edge
Motor ERD Sensitivity JOG JOG Motor Controller MC-200
OverLoad 5 LEFT RIGHT MATRIX ON-LINE Edge UL Entrap
4 3 1 POWER
ERD MAX 2
12 13 14 15 16 LED ON Limit SW Edge PhotoCell
POWER
POWER/SOLAR IN IN
TO MOTOR
CONTROLLER
BATTERY BATTERY
IN PACK
www.max.us.com
Made in USA
Secondary Operator
NO Matrix 1
to Secondary Operator
MC-200 Edge 2 or Photo Cell
OPENING direction Photocell
installation
Conduit Guidelines and Suggestions
• REQUIRED - Run AC input power wire to EACH gate operator.
• REQUIRED - Entrapment protection (photocell and/or sensing edge) to EACH Corresponding
GATE OPERATOR. (see below & page 13)
• Normally open photocell to the PRIMARY OPERATOR. (page 13)
• In-ground loop wires to the PRIMARY OPERATOR. (page 14)
Arms MUST be installed level.
To Matrix 1 SEC GATE input Conduit
Entrapment Area
OPENING/CLOSING direction Sensing Edges
to Secondary Operator
MC-200 Edge 2 or Photo Cell
See page 13 for installation instructions.
See pages 17-18 for wiring instructions.
Support Bars: See bottom of page 8.
"Optional" Input Power Note:
24VDC low voltage power wires can be run from a remote
power supply (MAX Magic Boxes) to power the gate
operators if desired. See page 11 for more information.
CLOSING direction Photocell
OPENING/CLOSING
direction Mini
Sensing Edge
to Primary Operator
MC-200 Edge 2 or Photo Cell
Primary Operator
Matrix 1
to Primary Operator
MC-200 Edge 2 or Photo Cell
Illustration not to scale
Primary
Operator
Matrix 1
MATRIX 1 BATTERY PRIMARY
BACK-UP MODE GATE
CLOSED LEAVE MAGLOCK
MADE in USA OPEN LEAVE OPEN 1 TIME LEFT OPEN RIGHT OPEN OFF DELAY 1.5Sec 2Sec MAG
LOCK COM
NC
AUTOMATIC OPEN/CLOSE CONTROLS
ANTI Tamper NO
TAILGATE EXIT CENTER SAFETY GATE COM
EXIT ON OFF TAMPER GND
Tamper IN
CENTER PHOTOCELL
SAFETY UL EDGE 1
MIN OFF MAX
CLOSE TIMER ENTRAP EDGE 2
ID PLUG
OPEN PARTIAL MOTOR MOTION ERROR
ID
PLUG UL ALARM 12V ALARM RET
OPEN STOP CLOSE RESET
RECORDER POSITION GND
12VDC MAX REVERSE SENSITIVITY
GND BLACK BOX OBD PORT GATE SPEED MOTOR OVERLOAD GATE OPEN
24VDC MIN NO LIMIT SWITCH / CLAMP SLIPPING STATUS COM
GND MAX CLOSE
SWITCH LIMIT BATTERY IN USE
ON-LINE
MOTOR ON-LINE POWER
PRIMARY GATE SEC GATE
Battery Voltage MAX BC-7
E 1/2 F Battery Module
ON/OFF Replace TEST Battery IN
Battery Battery Battery Error
6" Above
Ground
Conduit
Input
Power
To MC-200 EDGE 1 Input
Motor Sensitivity ERD JOG JOG Motor Controller MC-200
OverLoad 5 LEFT RIGHT ON-LINE MATRIX Edge UL Entrap
3 4 1 POWER
ERD MAX 2
12 13 14 15 16 LED ON Limit SW Edge PhotoCell
POWER
POWER/SOLAR IN IN
TO MOTOR
CONTROLLER
BATTERY BATTERY
MA TRIX MADE in USA 1 OPEN LEAVE BACK-UP MODE BA TTERY IN LEAVE CLOSED OPEN 1 TIME OPEN LEFT GA TE PRIMARY RIGHT OPEN MAGLOCK OFF 1.5Sec DELA Y PACK 2Sec MAG LOCK COM
EXIT AUTOMA TIC ANTI T AILGA TE ON OFF EXIT OPEN/CLOSE CENTER CONTROLS SAFETY T AMPER GA TE T amper NO COM NC GND
SAFETY CENTER MIN OFF MAX UL PHOTOCELL T amper IN EDGE 1
PLUG ID CLOSE TIMER PARTIAL OPEN MOTOR MOTION ENTRAP UL ALARM 12V EDGE 2 ERROR ID PLUG
24VDC GND 12VDC RECORDER OBD PORT BLACK BOX POSITION MAX MIN MAX GA TE SPEED OPEN REVERSE SENSITIVITY STOP NO LIMIT SWITCH / MOTOR OVERLOAD CLAMP SLIPPING CLOSE ST A TUS GA TE ALARM RET RESET CLOSE OPEN GND COM
GND PRIMARY GATE ON-LINE ON-LINE SWITCH LIMIT MOTOR GATE SEC BA TTERY IN USE POWER
www.max.us.com
Made in USA
OPENING direction Photocell
9