Table of Contents
Advertisement
Devices may only be transported by authorized and qua-
lified persons. Act responsibly during transport and al-
ways consider the consequences. Refrain from daring
and risky actions.
Gradients and descents (e.g. driveways, ramps and the
like) are particularly dangerous. If such passages are
unavoidable, special caution is required.
Before starting the transport check the transport route for
possible danger points, unevenness and disturbances
as well as for sufficient strength and load capacity.
Danger points, unevenness and disturbance points must
be inspected before transport. The removal of danger
spots, disturbances and unevenness at the time of trans-
port by other employees leads to considerable dangers.
Careful planning of internal transport is therefore essen-
tial.
CAUTION!
When transporting the saw with vehicles, there is a
risk of injury and damage to property due to inade-
quate or missing transport safety devices for the saw!
Before starting the journey, make sure that the trans-
port securing device is correct and safe.
Transport position model KGZ Series
The saw is transported or stored with lowered saw head.
To create the transport or storage position, perform the
following steps:
Step 1: Turn off the saw and remove the plug from the
socket. Clean the saw with a sawdust brush.
Step 2: Disassemble the support aids. The turntable lock
button, chamfer lock button and slide lock must
be tightened.
Step 3: Swing the tool arm on the handle (1) to the saw
table (5) until it reaches it.
Step 4: Turn the locking pin (21) by 90 ° and press it in to
secure.
Step 5: Remove the saw from the mounting pad by re-
moving the 4 screws in the saw feet.
When transporting the saw with fixed positions, make
sure that the saw head is locked in the lower position. Lift
the saw only on the operating handle (3) or on the outer
castings. Do not lift the saw with the guards.
To lock the saw head in the lower position. Press the
saw blade down and pull out the release button (2). Turn
the knob to lock the saw head. The head is locked in the
lower position.
KGZ Series | Version 2.02 | EN
Transport, Packaging and Storage
The tool arm is now securely locked for transport. Please
note that if the cutting depth is adjusted, the locking pin
may not work. Release the cutting depth limiter and then
lock the cutting head. The saw should never be used
with the release button securing the head down.
Transport lock Model KGZ 255 E
The locking pin (22) allows easier handling of the ma-
chine during transport to various work locations.
Model KGZ 255 E
Before you can transport the power tool, the following
steps must be taken:
Step 1: Bring the machine to the transport position.
Step 2: Remove all accessories that can not be firmly
connected to the power tool. Press the release
button (28) to secure the machine upside down
and with the pin (21). The saw is now locked in
its composition.
Step 3: If possible, put unused saw blades in a closed
container for transport.
Step 4: Wear the machine only on the base (11) or on
the carrying handle.
Note the dimensions of the saw. The power tool should
always be worn by two people to prevent back injury.
When transporting the power tool, only use the transport
devices and never the protective devices.
5.2 Packaging
All of the machine's packaging materials and packing
aids are suitable for recycling and must always be dispo-
sed of using material-based recycling systems.
Packaging materials made of cardboard must be shred-
ded and disposed of as part of waste paper recycling.
The foils are made of polyethylene (PE), padding is
made of polystyrene (PS). Dispose of these substances
at a recycling centre or hand them over to the relevant
waste disposal company.
5.3 Storage
Store the chop- and mitre saw thoroughly cleaned in a
dry, clean and frost-free environment. Cover the ma-
chine with a protective plane.
13
Advertisement
Table of Contents
