Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Holzstar KGZ 305 E
Summary of Contents for Holzstar KGZ 305 E
- Page 1 Operating Instructions Chop- and Mitre Saw KGZ 305 E KGZ 305 E...
-
Page 2: Table Of Contents
2.2 Personal protective equipment ......4 2.3 Safety labels on the chop- and mitre saw... 4 3 Intended Use............5 4 Technical Data ............5 4.1 Type plate KGZ 305 E ........5 Manufacturer 5 Transport, packaging and storage ......6 5.1 Delivery and transport......... 6 Stürmer Maschinen GmbH... -
Page 3: Introduction
We are always interested in valuable experience and knowledge gained from using the application, whichthen could be shared and be valuable to develop ourproducts even further. KGZ 305 E | Version 1.09 | EN... -
Page 4: Personal Protective Equipment
| 5 Warning of laser beam - not in the Laser beam look! | 6 Read operating instructions | 7 Safety information Head protection The industrial helmet protects the head against fal- ling objects and bumping into stationary objects. KGZ 305 E | Version 1.09 | EN... -
Page 5: Intended Use
Sound power level [db (A)] 101,4 dB(A) Electrical connection 230 V / 50 Hz The chop- and mitre saw KGZ 305 E is used for the pro- duction of cross sections, mitre cuts, double mitre cuts Motor output 2000 W and inclined cuts of boards and strips. -
Page 6: Transport, Packaging And Storage
Before starting the journey, make sure that the trans- port securing device is correct and safe. Safety position for transport Fig. 3: Chop- and Mitre Saw KGZ 305 E Note the dimensions of the saw. The saw should always 1. Carrying handle be transported by 2 persons. -
Page 7: Setting Up And Installation
Step 4: Screw the saw to the saw feet on a stable base. 45°, saw head tilted 45° Step 5: Insert the dust bag (Pos. A, Fig. 6) into the recep- tacle (Pos. B, Fig. 6) on the back of the saw. KGZ 305 E | Version 1.09 | EN... -
Page 8: Electrical Connection
(voltage, mains frequency, phase position) as the motor. Wear protective clothes! Step 1: Check that the cross-cut and mitre saw is swit- ched off. Step 2: Connect the saw to the mains. KGZ 305 E | Version 1.09 | EN... -
Page 9: Pre-Adjustment
(see Fig. 10). Snap-in points exist for 15° and 30° in both directions. Proceed as follows for the inclined position: Step 7: Tilt the locking knob and move the saw head a few degrees. KGZ 305 E | Version 1.09 | EN... - Page 10 (Pos. 16, Fig. 3) so that a cutting length of up to max. 340 mm. can be achieved. The longitudinal adjustment can be blocked or cancelled using the locking screw on the right-hand guide bush. KGZ 305 E | Version 1.09 | EN...
-
Page 11: Cutting Execution
Step 5: Lower the saw head onto the workpiece and make the cut. Step 6: When the cut is complete, release the on/off switch (2, Fig.13) and lift the saw head up until the saw head lock engages again. KGZ 305 E | Version 1.09 | EN... -
Page 12: Care, Maintenance And Repair
1.2 Customer Service. All protective and safety equipment must be immediately reinstalled after having completed repair and main- tenance work. Fig. 16: Unscrew the saw blade KGZ 305 E | Version 1.09 | EN... - Page 13 1/2". Check the functioning of the spring tension pulley. NOTE! Replace damaged V-belts or belts that can no longer be tensioned by the spring tension pulley. KGZ 305 E | Version 1.09 | EN...
-
Page 14: Disposal, Reusing Used Machines
Check the ease of movement of the carbon brushes in the bearing. ATTENTION! Always replace the carbon brushes in pairs! Step 4: Repeat the steps for the 2nd carbon brush. KGZ 305 E | Version 1.09 | EN... -
Page 15: Troubleshooting
Check whether the saw is fixed in the appropriate position so that the angle cannot adjust itself during sawing. Turntable is difficult to move The wood chips in the turning area Remove the the wood chips KGZ 305 E | Version 1.09 | EN... -
Page 16: Electrical Circuit Diagram
Risk of injury caused by the use of incorrect spare parts! The drive belt for the chop- and mitre saw KGZ 305 E The use of incorrect or faulty spare parts may cause must be ordered. The drive belt has the number 7 in the risks for operating staff and damage as well as mal- spare parts drawing 1. -
Page 17: Spare Parts Drawing Kgz 305 E
Spare parts 13.2 Spare parts drawing KGZ 305 E Fig. 22: Spare parts drawing KGZ 305 E KGZ 305 E | Version 1.09 | EN... -
Page 18: Ec Declaration Of Conformity
<= 16 A per phase and not subject to conditional connection Person responsible for the documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 18.06.2019 ______________________ Kilian Stürmer Managing Director KGZ 305 E | Version 1.09 | EN... -
Page 19: Notes
Notes 15 Notes KGZ 305 E | Version 1.09 | EN... - Page 20 www.holzstar.de...
Need help?
Do you have a question about the KGZ 305 E and is the answer not in the manual?
Questions and answers