Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Holzstar TKS 316 E
Summary of Contents for Holzstar TKS 316 E
- Page 1 Instruction Manual Table saw TKS 316 E - 230V TKS 316 E - 400V TKS 316 E...
-
Page 2: Table Of Contents
17.1 Ordering spare parts........21 and distribution of its content are prohibited if not explic- 17.2 Spare parts drawing TKS 316 E 230V_400V ..22 itly permitted. Contraventions are liable to compensa- 18 Electrical wiring diagrams TKS 316 E .. 24 tion. -
Page 3: Introduction
WARNING! even further. This combination of symbol and signal term indi- cates potentially hazardous situations which may cause death or serious injury if not averted. TKS 316 E | Version 1.02... -
Page 4: Personal Protective Equipment
The following applies in parti- cular: TKS 316 E | Version 1.02... -
Page 5: Personal Requirements
The various tasks described in this manual place diffe- thorized to perform these works. Please contact our cus- rent demands on the qualifications of the persons entru- tomer service for the execution of all arising work. sted with these tasks. TKS 316 E | Version 1.02... -
Page 6: Safety Signs On The Table Saw
120 mm. - Make sure that the workpiece can not move or slip when cutting round pieces. - Use suitable table extensions and support aids for hard-to-handle workpieces. TKS 316 E | Version 1.02... -
Page 7: Intended Use
Stürmer Maschinen GmbH assumes not use cracked or dull saw blades. Make sure that no liability. the screw of the saw blade is tight. Claims of any kind due to damage due to improper use are excluded. TKS 316 E | Version 1.02... -
Page 8: Residual Risks
WARNING! Risk of misuse! Misuse of the table saw can lead to dangerous situa- tions. - Never work on several workpieces at the same time. TKS 316 E | Version 1.02... -
Page 9: Type Plate
DANGER! Do not store the table saw unprotected outdoors or in a humid environment. Store the table saw thoroughly cleaned in a dry, clean and frost-free environment. Cover the machine with a protective tarpaulin. TKS 316 E | Version 1.02... -
Page 10: Description Of The Device
ATTENTION! Pay attention to the weight of the machine! The machine may only be set up by two persons. Fig. 3: TKS 316 E Description Check the aid accordingly for sufficient dimensioning 1. Connection suction and load capacity. -
Page 11: Assembly
- To install the extraction nozzle, fasten the extraction nozzle with 4 screws (U) on the side of the housing (Q) Fig. 8. Fig. 4: Assembly - Mount the Cross strut. Fig. 8: Mounting the extraction nozzle Fig. 5: Mount cross strut TKS 316 E | Version 1.02... -
Page 12: Mount The Rip Fence
- Attach two support arms as a brace (Y, Fig. 14). Set is running. the table horizontally and tighten the nuts and bolts. Fig. 14: Mount support arms Fig. 11: Adjusting the parallel stop TKS 316 E | Version 1.02... -
Page 13: Disassembly Of The Saw Blade
Thoroughly clean the flange before Fig. 17: Adjust saw blade fitting the new blade. Mount and fix the new saw blade in reverse order. Start the machine carefully. Fig. 16: Mount the saw blade TKS 316 E | Version 1.02... -
Page 14: Assembly Of The Splitting Wedge
Fig. 21: Mount bracket and guide tube - Guide tube cpl. Mount on the left side of the table top with a spacer plate (A) between the table and the front bracket (3). TKS 316 E | Version 1.02... - Page 15 (E), through the stopper tube, plastic washer (F) and segment, at the underside of the table with washer 8, spring washer and locknut M 8, tighten the toggle when pressing down. Fig. 26: Adjusting the sliding table guide TKS 316 E | Version 1.02...
-
Page 16: Set Up
CEE plug. confined spaces and must be stable on level, stable ground. Connections and repairs to the electrical equipment may only be carried out by a qualified electrician. TKS 316 E | Version 1.02... -
Page 17: Commissioning
In the pictures, the upper suction hood was only hinted at, or omitted in each case to show operation or device clearer. For all operations shown, the upper extraction hood is required. TKS 316 E | Version 1.02... -
Page 18: Cutting Narrow Workpieces
Devices requiring connection with parts of the machine must be fastened with screws, with screw clamps only makeshift connections can be made to machines. Fig. 31: Covering, folding Fig. 29: Cutting edges and strips TKS 316 E | Version 1.02... -
Page 19: Care, Maintenance And Repair
- Step 7: Check the machine regularly for: - Loose screws and nuts - Worn or damaged switches - Worn or damaged saw blade - Worn or damaged blade guard TKS 316 E | Version 1.02... -
Page 20: Troubleshooting
Step 3: Guide the machine components and operating materials to the appropriate disposal routes. Disused equipment must be taken out of service immedi- ately in order to avoid later misuse and endangering the environment or people. TKS 316 E | Version 1.02... -
Page 21: Disposal Of Electrical Equipment
Example malfunction. - Only original spare parts from the manufacturer or The engine for the table saw TKS 316 E - 230V must be replacement parts approved by the manufacturer ordered. The engine has the number 48 in the spare must be used. -
Page 22: Spare Parts Drawing Tks 316 E 230V_400V
The following drawings should help in case of service to identify necessary spare parts. To order, please send a copy of the part drawing with the marked parts to your authorized dealer. Fig. 32: Spare parts drawing TKS 316 E - 230V_400V TKS 316 E | Version 1.02... - Page 23 Spare parts Spare parts drawing 2 (Set 1) Fig. 33: Spare parts drawing 2 (Set 1) TKS 316 E - 230V_400V Spare parts drawing 3 (Set 2) Fig. 34: Spare parts drawing 3 (Set 2) TKS 316 E - 230V_400V...
-
Page 24: Electrical Wiring Diagrams Tks 316 E
Electrical wiring diagrams TKS 316 E 18 Electrical wiring diagrams TKS 316 E Electrical wiring diagram 230 V Fig. 35: Electrical wiring diagram TKS 316 E - 230V Electrical wiring diagram 400V Fig. 36: Electrical wiring diagram TKS 316 E - 400V... -
Page 25: Ec-Declaration Of Conformity
<= 16 A per phase and not subject to conditional connection Kilian Stürmer, Stürmer Maschinen GmbH, Responsible for documentation: Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 29.01.2019 ______________________ Kilian Stürmer Managing Director TKS 316 E | Version 1.02... - Page 26 www.holzstar.de...
Need help?
Do you have a question about the TKS 316 E and is the answer not in the manual?
Questions and answers