Table of Contents
Advertisement
Intended Use
42.When using an extension cord, make sure that the
cord is fully unwound and that its length is less than
30 meters. Lengths greater than 30 m affect tool per-
formance due to voltage drops.
43.Always stand on one side when operating the saw.
44. If the table insert is damaged or worn, have it re-
placed by an authorized service center.
45.Cloths, cloths, cords and threads and similar items
should never be left in the work area.
46.Keep the floor free of loose material such as chips
and cuttings.
47.When cutting long pieces that extend far beyond the
width of the table, ensure that the ends are sufficiently
supported at the same height as the saw table top.
Supports should be positioned so that the workpiece
does not fall to the floor.
48.Dust from materials such as lead-containing coatings,
some types of wood, minerals and metals can be
harmful to health and cause allergic reactions which
can lead to respiratory infections and/or cancer. Mate-
rials containing asbestos may only be processed by
specialists. Observe the relevant regulations for the
materials to be processed in your country.
49.Avoid accumulation of dust at the workplace. Dust
can easily ignite.
50.Never stand on the electrical tool. Serious injury may
occur if the electrical tool tips over or accidentally co-
mes into contact with the saw blade.
51.Never remove cutting debris, wood chips etc. from
the sawing area while the machine is running. Always
return the tool arm to its neutral position first and then
switch off the machine.
52.Only guide the saw blade against the workpiece when
the machine is switched on. Otherwise, the kickback
will be caused if the saw blade becomes wedged in
the workpiece.
53 Keep the handles dry, clean and free of oil and
grease. Greasy, oily handles are slippery and lead to
loss of control.
54.Only operate the electrical tool if the working area to
the workpiece is free of setting tools, wood chips, etc.
Small pieces of wood or other objects coming into
contact with the rotating saw blade can hit the opera-
tor at high speed.
55.Keep the floor free of wood shavings and material re-
sidues. You may slip or stumble.
10
56.Always clamp the part to be machined firmly. Do not
saw workpieces that are too small to clamp. Other-
wise the distance between your hand and the rotating
saw blade will be too small.
57.Use the machine only for cutting the materials listed
under the intended use. Otherwise the machine may
be overloaded.
58.If the saw blade becomes jammed, switch off the ma-
chine and hold the workpiece until the saw blade has
come to a complete stop. In order to prevent kickback,
the workpiece must not be moved until the machine
has come to a complete standstill. Eliminate the
cause of jamming of the saw blade before restarting
the machine.
59.Do not use blunt, cracked, bent or damaged saw bla-
des. Unsharpened or improperly adjusted saw blades
will produce a narrow kerf, resulting in excessive fric-
tion, blade lock and kickback.
60.Always use saw blades with the correct size and
shape of the hole. Saw blades that do not match the
saw's fasteners will run eccentrically, losing control.
61.Do not touch the saw blade after working until it has
cooled down. The saw blade becomes very hot when
you are working.
62.Never operate the machine without the insert plate.
Replace a defective insert plate. Without proper inser-
tion plates, injuries from the saw blade are possible.
63.Never leave the machine unattended before it has
come to a standstill. Cutting tools that are still running
can cause injury.
3
Intended Use
This chop- and mitre saw is intended for cutting wood
and analogue materials, it is suitable for straight and cur-
ved cuts having Mitre angles of up to 45°. The saw is not
designed for cutting firewood. Do not use machines,
tools and accessories for additional applications (see
manufacturer's instructions) for works other than those
for which they are designed for. All other applications are
expressly ruled out.
WARNING!
Danger in case of misuse!
- Never cut the several workpieces at the same time.
KGZ Series | Version 2.02 | EN
Advertisement
Table of Contents
