Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Holzstar FKS 315-2000 E
Summary of Contents for Holzstar FKS 315-2000 E
- Page 1 Operating instructions Panel saw FKS 315-2000 E FKS 315-2000 E...
-
Page 2: Table Of Contents
Copyright © 2020 Stürmer Maschinen GmbH, Hallstadt, 12.1 Spare parts orders ........... 23 Germany. 12.2 Spare parts drawings FKS 315-2000 E ... 24 13 Electric circuit diagram......32 The contents of these operating instructions is the sole 14 EC Declaration of Conformity....33 property of the company Stürmer Maschinen GmbH. -
Page 3: Introduction
We are always interested in valuable experience and tes a directly dangerous situation which may knowledge gained from using the application, whichthen cause death or serious injury if not averted. could be shared and be valuable to develop ourproducts even further. FKS 315-2000 E | Version 1.11... -
Page 4: Personal Protective Equipment
The dust protection mask protects the respiratory As soon as the signs are not clearly visible and compre- tract from wood chips and wood dust. hensible at first glance, the machine must be stopped until new signs have been attached. FKS 315-2000 E | Version 1.11... -
Page 5: General Safety Instructions
- Do not neglect to carry out regular inspections in - Never wear loose work clothing. accordance with the instructions for use. - Only use original HOLZSTAR spare parts and ac- - Check and ensure that the machine is not subject cessories. -
Page 6: Safety Equipment
Cover circuit breaker, FKS 315-2000 E Fig. 4: Reving knife and chip cover Intended use The Panel saw FKS 315-2000 E is used for sawing with versatile adjustable angles of boards and strips. The processing of solid wood, chipboard, panels and profiles is possible. -
Page 7: Technical Data
Observe the accident prevention regulations issued by your Employers Liability Insurance Association or other competent supervisory authority, responsible for your company. Fasten the loads properly. Fig. 5: Type plate FKS 315-2000 E FKS 315-2000 E | Version 1.11... -
Page 8: Packaging
Before starting the transport check the transport route for possible danger points, unevenness and disturban-ces Fig. 6: Panel saw FKS 315-2000 E as well as for sufficient strength and load capacity. 1 Telescope stop Danger points, unevenness and disturbance points must 2 Workpiece stop be inspected before transport. -
Page 9: Scope Of Delivery
Hose length 4 m. Step 2: Attach four eyebolts to the machine base and at- tach the risers to the eyebolts and over the forklift fork. Use a wooden block to protect the switch. FKS 315-2000 E | Version 1.11... - Page 10 Fig. 11: Mount extension table made of steel Step 3: Loosely screw the steel extension table to the cast iron table, align and center it, and then tigh- Fig. 14: Mount handwheels ten the screws.Anschlag-Führungsschiene mon- tieren FKS 315-2000 E | Version 1.11...
- Page 11 Fig. 17: Mount sliding carriage carrier Step 4: Insert two screws into the lower slots of the sli- ding carrier and screw the sliding carriage onto the carrier with two screws. FKS 315-2000 E | Version 1.11...
- Page 12 Step 9: Screw the hose guide to the back of the steel ta- ble with 2 M6x20 hexagon bolts, washers and nuts (nuts on the inside of the steel table). Fig. 22: Mount angle stop FKS 315-2000 E | Version 1.11...
-
Page 13: Electrical Connection
To ensure sufficient stability of the machine, it should be screwed to the ground. There are 4 holes on the machine housing for this purpose. ATTENTION! All work on the electrical installation may only be car- ried out by a qualified electrician. FKS 315-2000 E | Version 1.11... -
Page 14: Operation Of The Panel Saw
(kickback protection). CAUTION! Crushing! Incorrect work on the machine can cause injury to the upper limbs. FKS 315-2000 E | Version 1.11... -
Page 15: Sawing With The Sliding Table
Step 2: Adjust the stop to the desired cutting width. Step 3: Place the workpiece on the saw table. Fig. 31: ON-OFF switch FKS 315-2000 E 8.1 Sawing with the sliding table Fig. 34: Sawing operation with the saw table Step 4: Switch on the suction device, switch on the saw and carry out the sawing process. - Page 16 Step 5: Switch on the suction device, switch on the saw and carry out the sawing process. Fig. 39: Scales for miter cuts At the angle stop also scales for the implementation of Miter cuts are attached. FKS 315-2000 E | Version 1.11...
-
Page 17: Height Adjustment
Step 2: Empty and clean the suction device. Step 3: Vacuum the machine off sawdust and sawdust and clean with a dry cloth and / or compressed air (wear protective goggles!). In particular, the guide rails must be kept clean. FKS 315-2000 E | Version 1.11... -
Page 18: Maintenance And Repair
Step 7: Place the new saw blade with flange and nut on the shaft and tighten the nut (counterclockwise). ATTENTION! If the saw blade thickness has changed, an appropri- ately dimensioned cutting knife and a suitable auxili- ary saw blade must now be mounted. FKS 315-2000 E | Version 1.11... - Page 19 The cutting knife is partially structured. The structu- red area must be below the saw table. The fastening bolt is inserted in a slot so that the hori- zontal distance to the saw blade can be varied. FKS 315-2000 E | Version 1.11...
- Page 20 Step 2: Set the saw blade inclination angle to 0 ° (90 ° to the saw table) and move the saw blade up as far as possible. Step 3: Mark the center of the saw blade with a felt tip pen. Fig. 51: Release engine screws FKS 315-2000 E | Version 1.11...
-
Page 21: Disposal, Recycling Of Old Equipment
Material recycling helps to reduce the con- sumption of raw materials. For more information about recycling this product, contact your local community, mu- nicipal waste management, or the shop where you pur- chased the product. FKS 315-2000 E | Version 1.11... -
Page 22: Troubleshooting
2. Align the cutting blade with the saw blade saw blade. 3. Defective saw blade 3. Replace the saw blade. Braking time of the saw is longer Loose belt Tighten belt or replace if worn than 10 seconds. FKS 315-2000 E | Version 1.11... -
Page 23: Spare Parts
Spare parts 12 Spare parts Example The engine for the Sliding table saw FKS 315-2000 E DANGER! must be ordered. The engine has the number 47 in the spare parts drawing 3. Risk of injury due to incorrect spare parts! -
Page 24: Spare Parts Drawings Fks 315-2000 E
The following spare parts drawings is intended to help identify the necessary spare parts. To order, please send a copy of the list of spare parts with the marked components to your dealer. Spare parts drawing 1 Fig. 55: Spare parts drawing 1 FKS 315-2000 E FKS 315-2000 E | Version 1.11... - Page 25 Spare parts Spare parts drawing 2 Fig. 56: Spare parts drawing 2 FKS 315-2000 E FKS 315-2000 E | Version 1.11...
- Page 26 Spare parts Spare parts drawing 3 Fig. 57: Spare parts drawing 3 FKS 315-2000 E FKS 315-2000 E | Version 1.11...
- Page 27 Spare parts Spare parts drawing 4 Fig. 58: Spare parts drawing 4 FKS 315-2000 E FKS 315-2000 E | Version 1.11...
- Page 28 Spare parts Spare parts drawing 5 Fig. 59: Spare parts drawing 5 FKS 315-2000 E FKS 315-2000 E | Version 1.11...
- Page 29 Spare parts Spare parts drawing 6 Fig. 60: Spare parts drawing 6 FKS 315-2000 E FKS 315-2000 E | Version 1.11...
- Page 30 Spare parts Spare parts drawing 7 Fig. 61: Spare parts drawing 7 FKS 315-2000 E FKS 315-2000 E | Version 1.11...
- Page 31 Spare parts Spare parts drawing 8 Fig. 62: Spare parts drawing 8 FKS 315-2000 E FKS 315-2000 E | Version 1.11...
-
Page 32: Electric Circuit Diagram
Electric circuit diagram Spare parts drawing 9 Fig. 63: Spare parts drawing 9 FKS 315-2000 E 13 Electric circuit diagram Fig. 64: Electric circuit diagram FKS 315-2000 E FKS 315-2000 E | Version 1.11... -
Page 33: Ec Declaration Of Conformity
Part 1: Circular saw benches (with and without sliding table), dimension saws and building site saws Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 12.10.2020 ______________________ Kilian Stürmer Manager FKS 315-2000 E | Version 1.11... - Page 34 www.holzstar.de...
Need help?
Do you have a question about the FKS 315-2000 E and is the answer not in the manual?
Questions and answers