Intrinsyc Open-Q 660 User Manual page 34

Open-Q™ 660 HDK Hardware Development Kit based on the Snapdragon™ 660 processor User Guide Version 1.0
Figure 21 above shows the three MIPI CAM0 (J1701), CAM1 (J1801) and CAM2 (J1901)
connectors. The table below outlines the pin outs of these connectors
Table 3.8-12 MIPI CSI Camera Connector Pinouts (J1701, J1801, J1901)
Pin# CAM0(J1701)
1 MB_VREG_3P3
2 MB_VREG_3P3
3 MB_VREG_3P3
4 GND
5 MB_ELDO_CAM0
_AVDD
6 MB_ELDO_CAM0
_DVDD
7 MB_ELDO_CAM0
_VCM
8 MB_ELDO_CAM0
_VCM
9 VREG_LVS1A_1P
8
10 VREG_LVS1A_1P
8
11 GND
12 FLASH_STROBE
_EN
(SDA_GPIO40)
13 CAM0_RST_N
(SDA_GPIO46)
14 CAM0_STANDBY
_N
(SDA_GPIO44)
15 CCI_I2C_SCL0
(SDA_GPIO37)
16 CCI_I2C_SDA0
(SDA_GPIO36)
17 CAM_MCLK0_BU
F (SDA_GPIO32)
CAM1(J1801) CAM2(J1901)
MB_VREG_3P3 MB_VREG_3P3
MB_VREG_3P3 MB_VREG_3P3
MB_VREG_3P3 MB_VREG_3P3
GND GND
MB_ELDO_CAM1 MB_ELDO_CAM2_
_AVDD AVDD
MB_ELDO_CAM1 MB_ELDO_CAM2_
_DVDD DVDD
MB_ELDO_CAM1 MB_ELDO_CAM2_
_VCM VCM
MB_ELDO_CAM1 MB_ELDO_CAM2_
_VCM
VCM
VREG_LVS1A_1P VREG_LVS1A_1P
8 8
VREG_LVS1A_1P VREG_LVS1A_1P
8 8
GND GND
FLASH_STROBE FLASH_STROBE_
_EN EN (SDA_GPIO40)
(SDA_GPIO40)
CAM2_RST_N CAM1_RST_N
(SDA_GPIO48) (SDA_GPIO47)
CAM2_STANDBY CAM1_STANDBY_
_N N (SDA_GPIO50)
(SDA_GPIO51)
CCI_I2C_SCL0 CCI_I2C_SCL0
(SDA_GPIO37) (SDA_GPIO37)
CCI_I2C_SDA0 CCI_I2C_SDA0
(SDA_GPIO36) (SDA_GPIO36)
CAM_MCLK2_BU CAM_MCLK1_BUF
F (SDA_GPIO34) (SDA_GPIO33)
34
Copyright Intrinsyc Technologies Corporation
Description
Power output. Connected to main +3.3V
MB_VREG_3P3 max current 700mA
Power output. Connected to main +3.3V
MB_VREG_3P3 max current 700mA
Power output. Connected to main +3.3V
MB_VREG_3P3 max current 700mA
Ground
Power output. Connected to external LDO
output. Default MB_ELDO_CAM0_AVDD is
1.8V(DNI R0843 and solder R0844 to set
this power rail as +2.8V),
MB_ELDO_CAM1_AVDD and
MB_ELDO_CAM2_AVDD are +2.8V.
Maximum current 300mA
Power output. Connected to external LDO
regulator. Default value is set to
1.05/1.1/1.2V according to sensor spec .
Maximum current 500mA
Power output. Connected to external LDO.
Default is +2.8V. Maximum current 300mA
Power output. Connected to external LDO.
Default is +2.8V. Maximum current 300mA
Power output. Connected to PM660
VREG_L11A switch output. Default is
+1.8V. Maximum current 300mA
Power output. Connected to PM660
VREG_L11A switch output. Default is
+1.8V. Maximum current 300mA
Ground
Output. Connected to SDA660 Default use
is for camera flash strobe enable
Output. Connected to SDA660 GPIO46 /
GPIO47 / GPIO48. Default use is for
camera reset
Output. Connected to SDA660 GPIO44 /
GPIO50 / GPIO51. Default use is for
camera standby
Output. Connected to SDA660 GPIO37.
Default use is for camera CCI0 I2C clock
interface
Input / output. Connected to SDA660
GPIO36. Default use is for camera CCI0
I2C data interface
Output. Connected to SDA660 GPIO32 /
GPIO33 / GPIO34. Default use is for
camera master clock. Maximum 24MHz