Table of Contents
Advertisement
General Cleaning Instructions:
• Clean after each use.
• Make sure unit has cooled completely prior to cleaning.
• The outer surface may be cleaned by wiping carefully with a damp dishcloth or sponge.
• Remove the power plug prior to cleaning the NuWave™ Platinum. Do not use caustic
cleaning agents and water should not penetrate the interior of the induction cooktop.
• Never immerse the NuWave™ PIC Platinum, its cables or plug in water or other liquids.
• Wipe the glass surface with a damp cloth or use a mild, non-abrasive soap
solution. Make sure the unit has cooled completely before cleaning.
• Wipe casing and operating panel with a soft cloth dampened with water or a
mild detergent.
• Do not use oil-based cleansing products as their use may damage plastic parts
or the casing/operating panel.
• Do not use flammable, acidic or alkaline materials or substances near the
NuWave™ PIC Platinum, as this may reduce the service life of the induction
cooktop or pose a fire risk when the induction cooktop is in use.
• In order to keep your NuWave™ PIC Platinum looking like new, take measures
to ensure that the bottom of cookware does not scrape the unit's glass surface,
although a scratched surface will not impair the use of the induction cooktop.
• Make sure to properly clean the unit before storing it in a cool, dry place.
IMPORTANT TIPS:
1. Check power outlets to ensure proper operation. Do not use in an outlet
where other major appliances are engaged. Check settings if the unit is
cooking too slowly.
2. The electrical plug must be properly plugged into the outlet.
3. Always turn off and unplug the unit before wiping.
General Operating Instructions:
• Place the cooktop on a stable, level, non-metallic surface.
• Never use the cooktop on a flammable surface (e.g. table cloth, carpet, etc.).
• Do not block the ventilation slots of the induction cooktop. This may cause
the unit to overheat. Maintain a minimum distance of 3-5 inches from walls
and other objects, appliances, etc.
• Do not place devices or objects that are sensitive to magnetic fields on
top of or next to the NuWave™ PIC Platinum.
(e.g. credit cards, cell phones, radios, TVs, video recorders, etc.).
• Do not use the induction cooktop in the proximity of open fires,
heaters or other heat sources.
• Do not place on stove top.
• Ensure that the power cable is not damaged or compressed
beneath the induction cooktop.
• The power cable must not come into contact with sharp edges and/or hot surfaces.
• Prior to connecting the NuWave™ PIC Platinum, confirm that the voltage
needs indicated in this manual correspond to the voltage supply in your home.
A wrong connection may lead to the unit's damage and possible injury to persons.
• The cooktop's surface is designed from temperature-resistant glass. In the event
that damage to the unit is observed, even a small crack on the glass surface,
immediately disconnect the NuWave™ PIC Platinum from the power supply.
12 • NuWave
PIC
Platinum Complete Cookbook
™
®
Directions for the Display Panel
Program
Watts
Decrease
Increase
End
Time
Stage
Cook
Cook
Low-Max/Sear
Temperature
Time
LED Display
Control Panel:
LED Display should read "0" when program is
clear or power is on.
Easy Start:
NOTE: Ensure that your NuWave™ PIC Platinum is turned on
by flipping the on/off switch on the right hand side of the PIC.
The NuWave™ PIC Platinum is defaulted to cook on Med/High (375°F) for 1 hour. To begin
IDC 4 Control Panel Graphic
cooking, press the "Start" button, after placing an induction-ready pot on the surface. To cook
at a different temperature setting, press one of the 6 main temperature buttons, or press the
"+" or "-" arrows to decrease or increase the temperature in 5°F increments.
See Setting Temperature for more details.
Setting Clock Time And AM/PM Button:
1. Press the "Clock" button. CLOCK indicator will flash on LED display
and "00:00" will be displayed.
2. Enter digits to match the current time.
• For example, 1:25 would be entered by pressing "1,2,5".
3. Once entered, the time will be set as AM as a default.
4. To change to PM, press the "am/pm" button.
5. Press the "Clock" button again to set.
• "End Time" feature will not work unless the time is set and "0" is shown in the display.
• If the NuWave™ PIC Platinum is cut from a power supply or
turned off, the clock must be reprogrammed.
Fahrenheit to Celsius Conversion:
1. The NuWave™ PIC Platinum's LED display is defaulted to display cooking temperature in
Fahrenheit (F) and the F will appear on display panel.
2. To switch the display to Celsius(C), press the "Cook Temp" and "Cook Time"
buttons simultaneously.
3. To close out of the F/C conversion option, press the "Pause/Clear" button until "0"
or the current time appears on the unit's screen.
Lock And Unlock Function:
The PIC can be locked by pressing
"Low" and "Sear/Max" simultaneously until
"LOCK" is displayed on the LED display.
To unlock, press "Low" and "Sear/Max"
simultaneously until "LOCK" is no longer
displayed on the LED display.
LED
Pause/
Display
Clear
Start
Number
Clock
AM/PM
Owner's Manual • 13
Advertisement
Table of Contents
