Input Mode 输入模式 - PRESONUS StudioLive III Series Owner's Manual

6.3 Input Mode 输入模式
Pressing the Input button in the Fat Channel gives you access to important controls
and informative displays for the currently selected channel or mix.
Note: These controls are fixed on the StudioLive 32SX and 32SC. For all other models,
pressing holding the Input button will lock or unlock these functions to the Dynamic Fat
Channel controls.
在 Fat Channel 中按下 Input 按钮，可以访问当前所选通道或混音的重要控制和信
息显示。
注意：这些控制在 StudioLive 32SX 和 32SC 上是固定的。对于所有其他型号，按
住输入按钮，将锁定或解锁这些功能到 Dynamic Fat Channel controls 控制。
1 2 3
GATE
PAN
PREAMP
Gain Thresh
0 dB < C > -84.00 dB
AGC Center Gate
1. Preamp Gain (Input Channels only). Use the encoder to set the amount
of preamp gain applied to the currently selected channel. The scribble strip
displays the current gain level. Press the button below to enable Automatic Gain
Compensation. For more information on Gain Compensation, please see the
NSB-series Stage Box Owners Manual.
使用编码器，设置应用于当前所选通道的前置放大器的增益量。scribble
strip
显示当前的增益水平。按下面的按钮，可以启用自动增益弥补。关于增
益弥补的更多信息， 请参见 NSB 系列舞台箱用户手册。
Pan. Use the encoder to set the currently selected channel or subgroup's pan
2.
position across the stereo field. The pan position will be displayed on the
Scribble Strip. Press the button below the encoder to reset the pan position to
Center.
使用编码器来设置当前选择的通道，或subgroup在立体声场中的声音位
置。Pan声音位置将显示在Scribble Strip上。按编码器下面的按钮，可以将
Pan重置为中心。
3. Gate Threshold. The encoder sets, and the scribble strip displays, the gate
threshold for the selected channel. The gate threshold sets the level at which
the gate opens. Essentially, all signals above the threshold setting are passed
through unaffected, whereas signals below the threshold setting are reduced
in level by the amount set by the range control. If the threshold is set fully
counterclockwise, the gate is turned off (always open), allowing all signals to
pass through unaffected. You can set the threshold from 0 to -84 dB. See
Section 6.4 for more information on the Noise Gate and its parameters.
编码器设置，scribble strip显示所选通道的门限。门限设定了门打开的电
平。从本质上讲，所有高于门限设置的信号都不会受影响，而低于门限设
置的信号，则按设置范围控制的量降低电平。如果门限值被逆时针完全设
定，那么门限值就会被关闭（总是打开），允许所有的信号不受影响地通
过。你可以将门限设置在0到-84dB之间。 关于噪声门及其参数的更多信息
见第 6.4 节。
4. Compressor Threshold. This encoder sets, and the scribble strip displays, the
compressor threshold for the selected channel or output bus. When the
signal's amplitude (level) exceeds the threshold setting, the compressor
engages. Turning the knob counterclockwise lowers the threshold so that
compression begins at a lower amplitude. The threshold can be set from -56
to 0 dB. See Section 6.5 for more information on the Compressor and its
parameters.
这个编码器设置，并在 scribble strip上显示所选通道或输出总线的压缩
器门限。当信号的振幅（电平）超过阈值设置时，压缩器开始工作。 逆
时针旋转旋钮可以降低门限，在较低的振幅下开始。阈值可以设置为-56
到0dB。关于压缩器及其参数的更多信息， 见第 6.5 节 。
4 5 6 7
EQ EQ
COMP HI PASS
Thresh Filter Gain Freq
0.00 dB 0.00 dB 1.40 kHz
off
B1 B2 B3
Comp
8
EQ
Q
0.60
B4
48