PRESONUS StudioLive III Series Owner's Manual page 72

6 The Fat Channel
6.3 Input Mode
5. High-Pass Filter. Use the encoder to set the High-Pass Filter Frequency
Threshold for the Selected Channel or Output Bus. The filter's threshold can be
set from 24 Hz to 1 kHz. When the threshold is set to its lowest point, the filter is
off. The high-pass filter's slope is - 12 dB/8va. Press the button below to enable
the Low Band (B1) for control.
使用编码器，来设置所选通道或输出总线的High-Pass Filter Frequency
Threshold 阈值。Filter 阈值可以设置在24Hz到1kHz之间。设置阈值到最低
点时，滤波器关闭。高通滤波器的斜波是-12dB/8va。按下面的按钮，启
用低频段（B1）进行控制。
Power User Tip: A high-pass filter attenuates all frequencies below the set threshold. Use
the Fat Channel high-pass filter to remove unwanted low-frequencies from your source
signal, rather than trying to EQ them out.
Power User Tip: 高通滤波器衰减所有低于设定阈值的频率。使用 Fat Channel 高通
滤波器从你的源信号中去除不需要的低频，而不是试图将它们均衡化。
6. EQ Gain. Sets the amount by which the selected frequency will be boosted or
cut. Press the button below to enable the Low Mid Band (B2) for control.
设定所选频率被提升或削减的量。按下面的按钮，可以启用中低频段（B
2）进行控制。
7. EQ Frequency. Sets the center frequency at which signals are boosted or cut for
the current EQ band. Press the button below to enable the High Mid Band (B3)
for control.
设置当前均衡器频段的信号被提升或削减的中心频率。按下面的按钮，可
以启用中高音段（B3）进行控制。
8. EQ Q. Sets the Q (or width) of the current EQ band. Larger Q values affect a
narrower range of frequencies. Lower Q values affect a wider range. Press the
button below to enable the High Band (B4) for control.
设置当前均衡器频段的Q值（或宽度）。较大的Q值影响较窄的频率范
围。较低的Q值则影响较宽的范围。按下面的按钮，可以启用高频段（
B4）进行控制。
Pressing the Next Page button in the Fat Channel provides access to additional
parameters.
在Fat Channel 中按下 "Next Page" 按钮可以访问更多的参数。
Note: These controls are not available from the Fat Channel on the
StudioLive 32SX and 32SC.
注意：在StudioLive 32SX和32SC上，这些控制不能从Fat Channel上使用。
StudioLive 32SX 和 32SC 上没有这些控制。
1 2 3
DELAY
LIMIT MONO
Thresh Send
0.00 dB 2.6 ms
2.46 dB
Lim
1. Limiter Threshold. This encoder sets, and the scribble strip displays, the
threshold of the limiter for the selected channel or output bus. When the signal's
amplitude (level) exceeds the threshold setting, the limiter is engaged. Turning
the knob counterclockwise lowers the threshold, so limiting begins at a lower
amplitude. The Limiter ratio is ∞:1.
这个编码器设置了所选通道或输出总线的限制器的门限，并在scribble strip
上显示。当信号的振幅（电平）超过门限的设置时，限制器开始工作。可
以逆时针旋转旋钮，降低门限值，因此限制器从较低的幅度开始。限制器
的比例是∞：1。
2. Mono Send / Center Divergence (StudioLive 64S only). The encoder sets the
Mono Send level or the Center Divergence percentage depending on the Pan
Mode set in the System Menu. The button toggles between Pre- and Post-fader
send to the Mono Bus. For more information on the Mono Bus, seeSection 5.6.
StudioLive™SeriesIII
Owner's Manual
49