Page 3
Product Warranty Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products that have been repaired or...
Page 4
This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information.
Ethernet, Wireless LAN, RS-232/ 422/485 and so on. Because of its openness, great expansion capability and reliable design (fanless and diskless), the UNO-2000 series are ideal embedded platforms for implementing custom applications for diversi- fied applications.
• Chassis Size (W × L × H): 255 x 152 x 69 mm (10”× 6.0”× 2.7”) • Software options: Windows XP Embedded, Win/2000/XP • Certification: CE, FCC Class A, UL 1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable.
• PCI-104 bracket (Advantech P/N : 1960008884) • 2 Standard posts for install PCI-104 card (Advantech P/N : 193A231540) • 2 screws (M3*15L) for install PCI-104 bracket on UNO (Advantech P/ N : 1935131510) • Warranty card If anything is missing or damaged, contact your distributor or sales repre- sentative immediately.
Page 13
Hardware Functionality This chapter shows how to setup the UNO-2182’s hardware functions, including connecting peripherals, set- ting switches and indicators. Sections include: • Peripherals • RS-232 Interface • RS-232/422/485 Interface • LAN / Ethernet Connector • Power Connector • PS/2 Mouse and Keyboard Connector •...
Chapter 2 Hardware Functionality 2.1 Introduction The following two figures show the connectors on UNO-2182. The fol- lowing sections give you detailed information about function of each peripheral. Figure 2.1: UNO-2182 Front Panel Figure 2.2: UNO-2182 Rear Panel 2.2 RS-232 Interface (COM1~COM2) The UNO-2182 offers two standard RS-232 serial communication inter- face ports: COM1 and COM2.
COM3 and COM4. Please refer to Appendix A.4 for their pin assignments. The default setting of COM3 and COM4 are RS-422/485. 2.3.1 16C550 UARTs with 16-byte standard Advantech UNO-2182 comes with TI16C550 UARTs containing 16 bytes FIFOs. 2.3.2 RS-422/485 detection In RS-422/485 mode, UNO-2182 automatically detects signals to match RS-422 or RS-485 networks.
Description TX+/TX- for COM3 Data+/Data- for COM3 RX+/RX- for COM3 TX+/TX- for COM4 Data+/Data- for COM4 RX+/RX- for COM4 2.3.5 RS-232/422/485 Selection COM3 and COM4 support 9-wire RS-232, RS-422 and RS-485 inter- faces. The system detects RS-422 or RS-485 signals automatically in RS- 422/485 mode.
2.3.6 RS-485 Auto Flow & RS-422 Master/Slave Mode You can set the “Auto Flow Control” mode of RS-485 or “Master/Slave” mode of RS-422 by using the SW4 DIP switch for each RS-422/485 port. In RS-485, if the switch is set to “Auto”, the driver automatically senses the direction of the data flow and switches the direction of transmission.
2.3.7 IRQ and Address Setting The IRQ and I/O address range of COM3 and COM4 are listed below: • COM3: 3E8 , IRQ10 (Independent IRQ), IRQ10 (Share IRQ) • COM4: 2E8 , IRQ5 (Independent IRQ), IRQ10 (Share IRQ) • Vector address for share IRQ: 1D0 You can set “Share IRQ”...
2.4 LAN: Ethernet Connector The UNO-2182 is equipped with a Realtek RTL8111B Ethernet LAN controller that is fully compliant with IEEE 802.3u 10/100Mbps Ethernet and also IEEE 802.3ab 1000Mbps Ethernet.. The Ethernet port provides a standard RJ-45 jack on board, and LED indicators on the front side to show its Link (Green : 1000 Mbps network, Orange : 100 Mbps network, Blank : 10Mbps network.) and Active (Yellow LED) status.
2.9 VGA Display Connector UNO-2182 provides DVI-I interface, you could link you DVI or VGA monitor through DVI-I to DVI and VGA cable. (Advantech P/N : 1700004713), As for detail DVI-I pin assigmnet, please refer A.10. The UNO-2182 provides a VGA controller (Intel 945GM GMCH for a high resolution VGA interface.
Figure 2.5: SRAM Lithium Battery Location 2.10.2 Jumper Setting for SRAM You could set up SRAM enable or diable by jumper CN44. SRAM Enable/Disable Jumper Setting (CN44) Status Function Open Enable SRAM function (Default) Closed Disable SRAM function Chapter 2...
2.11 Reset Button Press the "Reset" button to activate the reset function. (SW2) 2.12 Power Button Press the "Power" button to power on or power off UNO-2182. (ATX type) (SW3) UNO-2182's power is also designed for power management only "S1" compliant.
Page 23
Initial Setup This chapter introduces how to initial- ize the UNO-2182. Sections include: • Chassis Grounding • Inserting a CompactFlash Card • Installing a Hard Disk • Connecting Power • BIOS Setup and System Assignments • Installing PCI-104 Modules...
Chapter 3 Initial Setup 3.1 Chassis Grounding The aluminum made UNO-2182 provides good EMI protection and a sta- ble grounding base. There is an easy-to-connect chassis grounding point for you to use. Please connect chassis ground of UNO-2182 with "EARTH" as ground. Figure 3.1: Chassis Grounding Connection Note: UNO-2182 is design as system power ground...
Note CN8 is primary's master CN7 is Primary Please do not use CN8 and CN7 at same time. If your OS is build in CF card and program,applica- tion and data are save in HDD, please install CF in CN8 and connect SATA HDD in CN40 (SATA signal) and CN41 (SATA power), please also refer CN40 and CN41 pin assignment in A.11.
3.5 BIOS Setup and System Assignments UNO-2182 adopts Advantech’s SOM-5782 CPU module. Further infor- mation about the SOM-5782 CPU module, can be found in SOM-5782 user’s manual. You can find this manual on the UNO-2182’s driver and utility CD-ROM.
3.6 Installing PCI-104 Modules If you need install PCI-104 module on UNO-2182, please refer below procedure. Make sure power core is not connected with UNO-2182. Unscrew the four screws from the rear panel. Slide off down cover of UNO-2182. Unscrew four screws from PCB, please refer below picture. Screw up 2 post and PCI-104 bracket in accessory, please refer below picture.
Page 28
Install PCI-104 card and screw up 4 screws which removed from UNO-2182 PCB, please refer below picture. Installation complete. Note: If only function test, UNO-2182 could integrate PCI-104 card without UNO-PCM22, if you need a whole set chassis, you have to assembly with UNO-PCM22 for whole UNO set.
A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-2182 board. The following sections tell you how to configure the UNO-2182 hardware set- ting. Figure A-1 and Figure A-2 show the locations of UNO-2182’s con- nectors and jumpers. Figure A.1: Connectors &...
Page 33
Table A.3: UNO-2182 Connectors and Jumpers Label Function Phoenix power connector CN31 Ethernet port 1 & 2 CN18 COM1 RS-232 serial port CN19 COM2 RS-232 serial port CN20 COM3 RS-232/422/485 serial port CN23 COM4 RS-232/422/485 serial port COM3/COM4 RS-422 master/slave selection Share IRQ/Independent IRQ selection /Speed selection CN24 COM3 RS-232/422/485 selection...
A.6 Phoenix Power Connector (PWR) Table A.7: Power connector pin assignments Signal Name +9 ~36 VDC A.7 PS/2 Keyboard and Mouse Connector Table A.8: Keyboard and Mouse connector pin assignments Signal Name KB DATA MS DATA KB Clock MS Clock UNO-2182 User Manual...
A.8 USB Connector (USB1~USB2) Table A.9: USB connector pin assignments Signal Name Cable Color DATA+ White DATA- Green Black A.9 VGA Display Connector (DVI-I to DVI & VGA Cable) Table A.10: VGA adaptor cable pin assignment Signal Name Green Blue H-SYNC V-SYNC Appendix A...
A.11 External & Internal SATA Connectors Table A.12: External SATA connector pin assignment Signal name Table A.13: Internal SATA DATA Connectors (CN40) Signal name Appendix A...
Page 40
Table A.14: Internal SATA Power Connectors (CN41) Signal name +12V +12V UNO-2182 User Manual...