Xylem Ai1 Product Manual page 2

Warranty
Limited Warranty: Ai1 products are warranted to be free from defects in materials and workmanship under normal
use and service for twelve (12) months from the date of shipment unless otherwise specified. Batteries, desiccant,
and other consumables have no warranty. The Ai1 is Manufactured by Measurement Science. The Manufacturers
obligation under this warranty is limited to repairing or replacing (at the Manufacturers option) defective Products,
which shall be the sole and exclusive remedy under this warranty. Products may not be returned without prior
authorization. The Customer assumes all costs of removing, reinstalling, and shipping Products to The Manufacturer.
For all returns, The Customer must fill out a "Statement of Product Cleanliness and Decontamination" form and
comply with the requirements specified in it. The Manufacturer reserves the right to refuse service on products that
were exposed to contaminants that may cause health or safety concerns. The Manufacturer will return such
Products by surface carrier prepaid within Australia. To all other locations, The Manufacturer will return such
Products best way CIP (port of entry) per Incoterms® 2010. This warranty shall not apply to any Products which have
been subjected to modification, misuse, neglect, improper service, accidents of nature, or shipping damage. This
warranty is in lieu of all other warranties, expressed or implied. The warranty for services performed by The
Manufacturer such as programming to Customer specifications or product specific training, is part of The
Manufacturers product warranty. Ai1 products are intended to be part of a well maintained and comprehensive
monitoring system. Reliable operation depends on suitable site selection, correct installation, real time monitoring of
data, adequate maintenance and investigation of alarm and diagnostic information. Stations are designed to be
mounted above water; submersion may result in damage. All ownership and risk transfers to the purchaser at the
time of shipment. The Manufacturer does not accept any liability or consequential damages for any failure of
systems supplied. Repair or service of the system is only to be handled by factory trained technicians. No service by
The Customer is allowed. Refer to terms and conditions of sale for full details. THE MANUFACTURER EXPRESSLY
DISCLAIMS AND EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. The Manufacturer hereby disclaims, to the fullest extent allowed by applicable law, all warranties, and
conditions with respect to the Products, whether express, implied or statutory, other than those expressly provided
herein.
Precautions
DANGER — MANY HAZARDS ARE ASSOCIATED WITH INSTALLING, USING, MAINTAINING, AND WORKING ON OR
NEAR ROADS, RIVERS, WATER BODIES, ELEVATED PLATFORMS, REMOTE LOCATIONS AND OTHER SIMILAR HAZARDS.
You are responsible for conformance with governing codes and regulations, including safety regulations, and the
integrity and location of sites. Installation sites should be evaluated and approved by a qualified engineer. Prior to
performing site or installation work, obtain required approvals and permits. Comply with all governing permits and
use only qualified personnel. The use of licensed and qualified contractors is highly recommended. Read all
applicable instructions carefully and understand procedures thoroughly before beginning work. Wear all relevant
personal protective equipment, including a hardhat and eye protection, and take other appropriate safety
precautions while working. You can be killed or sustain serious bodily injury if the system you are installing,
constructing, using, or maintaining, or a tool, stake, or anchor, contact overhead or underground utility lines. Prior
to performing site or installation work, inform all utility companies and have all underground utilities marked.
Comply with all electrical codes. Electrical equipment and related grounding devices should be installed by a licensed
and qualified electrician. Protect all equipment from over-voltage, water, and electrostatic discharge. Do not
perform any work in inclement weather, including wind, rain, snow, lightning, etc. Periodically (at least yearly) check
for wear and damage, including corrosion, stress cracks, frayed cables, loose clamps, fastener tightness, electrical
ground connections, etc. and take necessary corrective actions. While every attempt is made to embody the highest
degree of safety in all products, the customer assumes all risk from any injury resulting from improper installation,
use or maintenance of these products. The Manufacturer recommends a level of calibration appropriate to the
application, and recommends, at a minimum, recalibration every three years.
The Ai1 is globally by Xylem Analytics. Please contact your local distributor for support.
Page | 2