Led Indicators; Lcd Indicators - ABB PowerValue RT G2 User Manual

18 A B B U P S P R O D U C T S A N D S O L U T I O N S

5 .1 .2 LED Indicators

There are 4 LEDs on front panel to show the UPS
working status:
LED
UPS Power On
Standby mode
Bypass mode
Line mode /
CVCF mode
Battery mode
Fault mode
Battery Test
mode
ECO mode
Note: l means LED is lighting, and l means LED

5 .1 .3 LCD Indicators

（1）
I P 1 : 1 2 0 . 0 V / 6 0 . 0 H z
I P 2 : 1 2 0 . 0 V / 6 0 . 0 H z
O P 1 : 1 2 0 . 0 V / 6 0 . 0 H z
O P 2 : 1 2 0 . 0 V / 6 0 . 0 H z
B a t : 1 2 0 . 0 V / 1 2 0 . 0 V
L o a d : 0 /
W a r n i n g : 0 0
The LCD screen is divided into four parts:
(1). UPS Mode: Current operation mode
(2). Display the UPS running status mode and par
allel information as below table.
Short
Description
N
M
S<n>
(3). Input and output information.
Y Y i i _ _ L L i i u u 2 2 0 0 2 2 2 2 - - 0 0 1 1 - - 2 2 1 1
(4).Battery capacity, load level and backup time/
warning or fault codes.
The LCD backlight automatically dims after two
minutes of inactivity (except in cases of a UPS
fault). Press any button to wake up the screen.
When the front panel is not operated for 2
minutes, the display page will return back to
home page. Press the "UP" or "DOWN" button to
enter the operation menu
A buzzer indicates UPS status. The follow table
lists are the buzzer status meanings.
Function
BYPASS LINE
l l
l l
l l
l l
l l
l l
l l
l l
is faded.
Line Mode M
（1）
（2）
I P 1 : 0 . 0 V / 0 . 0 H z
（3） I P 2 : 0 . 0 V / 0 . 0 H z
O P 1 : 1 2 0 . 0 V / 6 0 . 0 H z
O P 2 : 1 2 0 . 0 V / 6 0 . 0 H z
B a t : 1 2 0 . 0 V / 1 2 0 . 0 V
L o a d : 0 /
0 / - - - - %
B a c k T i m e ： 1 0 H
（4）
Description
New adding module into parallel system.
Master
Slave, <n> means the number of slave module.
Y Y i i _ _ L L i i u u 2 2 0 0 2 2 2 2 - - 0 0 1 1 - - 2 2 1 1
5 .1 .4 Table Audible alarm
UPS status
BATTERY ALARM
Bypass mode
Battery / Battery-test
l l
mode (normal battery
voltage)
l l
Battery / Battery-test
l l
mode (low battery
voltage)
l l
Fault
l l Warnings (except
overload)
l l
Overload
l l
When powering on, the LCD shows the UPS status.
l l
The UPS will also return to this default screen when
no buttons have been pressed for 15 minutes.
For more information on how to use the LCD, see
Chapter 5.3 and 5.4.
The status screen shows the following information:
Bat Mode S1 • Status summary, including operating mode and
（2）
load information and Input and output voltage and
（3）
frequency
• Alarm status, if present (including fault and
warning information)
0 / - - - - %
• Battery and charger status (including battery
（4）
voltage, charge level and charger status)
• Current runtime information
Buzzer status Can be disable
Beeping once Yes
every 2 minutes
Beeping once Yes
every 4 seconds
Beeping once Yes
every second
Beeping Yes
continuously
Beeping once No
every second
Beeping twice No
every second