Maximum Controls MAX ARM Installation And Owner's Manual page 55

i gaze RE kit monitored WIRELESS
OPEN ONLY NC
PHOTO CLS NC
OPEN/CLS NC
12VDC OUT
GND
OPEN ONLY O O O O O 10K
C CLS ONLY C 10K
OPEN/CLS 10K
12VDC OUT
GND
BATTERY
DSP ARM CONTROLLER P ARM CONTROL
BATTERY VOLTAGE TTERY VOLTAGE
INPUT
ERROR
E 1/2 1/2 F F
BATTERY
BATTERY BATTERY
INPUT
BACKUP MOD BACKUP MODE
BATTERY
LEAVE LEAVE
IN USE
OPEN OPEN
REPLACE REPLACE
LEAVE LEAVE
BATTERY BATTERY BATTERY
CLOSED CLOSED
TEST
POWER /
SOLAR IN
POWER
ERD SENSITIVITY D SENSITIVITY
14 12 14 14 12 12
16 16 16
MIN
ERD D MIN MIN E ERD
9 9 9
1 1 1
MOTOR OR MOT MOTOR
MODULE MAX MAX MAX
SENSE OVER SENSE SENSE OVER OVER
PORT 3 7 7 7
3 3
LOAD LOAD LOAD
OPENING CLOSING CLOSING
OBD PORT
BLACK BOX
MAXIMUM CONTROLS M CONTROLS
RESET
OFF
DSP ARM CONTROLLER CONTROLLER
1
2
ALARM 3
4
5 MOTION CONTROL ONTROL
PROGRAMMING
ID PLUG
6
ERROR
1
2
3
ID
4
PLUG 5
6
7
PROGRAM OPEN STOP CLOSE OSE
8
9
10
OFF
ANTI-
PUSH
EXIT PWR
TAILGATE
SOLAR MODE OPEN
EXIT LOOP
OFF ON
GND
OFF ON
GATE
CENTER LOOP
LOOP PWR CLOSING GATE SPEED
OPERATOR
SAFETY LOOP
MIN MIN
FAULTS
MAX MAX
SINGLE DUAL
24VDC OUTPUT
GND MOTOR 1 MOTOR 2
12VDC OUTPUT
GND
Wireless Receiver/Transmitter Programming:
1. Make sure receiver and transmitter have power.
2. Press and HOLD
Release button.
3. Press and HOLD
are heard.
Prog/Test 1
Release button.
Repeat steps for
Prog/Test 2
NOTE: See iGaze RE Wireless kit instruction sheet for
complete installation and programming instructions.
MAX Arm/Ultra Arm V1
RCOO900
Receiver
12/24 VAC/DC C1 NC1 NO1 C2 NC2 NO2 Test1 Test2 TestC Program
+ -
5 & 6 MUST be
ON for 10K input
Both safety edges
are 10KΩ resistive
[+]
MOTOR 1
INPUTS [-]
MOTOR 2 [+]
INPUTS [-]
LIMIT 1
MOTOR MOTOR 1
LIMIT 2
LIMIT 1
MOTOR 2 MOTOR 2
CLOSE CLOSE
L LIMIT 2
TIMER TIMER
LIMIT 1
MIN MAX MAX
MOTOR 1 MOTOR 1
GND
OFF OFF
LIMITS LIMITS
LIM LIMIT 2
ON/OFF
BATTERY
JOG
OPEN OPEN CLOSE
PULL LL MAGLOC MAGLOCK
OPEN N DELAY DELAY
OPEN / CLS
OFF OFF
1.5 sec 1.5 sec
GND
UL UL OPEN ONLY 10K
ENTRAP ENTRAP
CLS ONLY 10K
OPEN / CLS 10K
12VDC OUT
GND
PROGRAM/RESET button on receiver until ONE "BEEP" is heard.
PROG/TEST 1 button (Safety 1) on transmitter until TWO "BEEPS"
PROG/TEST 2 button (Safety 2) on transmitter if second edge is used.
Reset
Wire NO2 for Safety 2 on transmitter
Wire NO1 for Safety 1 on transmitter
Receiver
DIP-Switches
1-OFF
2-OFF
3-OFF
Frequency
4-OFF
5-ON
6-ON
Mount transmitter as high as
possible on gate.
Minimum of 8" above ground.
0
9 0
R C
O O
r
i t t e
T C
R e
n s m
T r a
Z E Z E
G A G A
Wire 10K Edges
TCOO900
Transmitter
Prog/Test 1 Prog/Test 2
Safety 1 Safety 2
ON
Safety 1
1 2 3
Configuration
Can be mounted on
ON
Gate's OPENING OR
CLOSING position.
Set to OFF
1 2 3
Frequency DIP-switches 2 & 3 MUST be set
the same as the receiver DIP-switches 3 & 4.
E
GAZ
0
9 0
O O
v e r
c e i
R E R E
Z E Z E
G A G A
Safety 2
Can be mounted on
Gate's OPENING OR
CLOSING position.
53