Open / Stop / Close Inputs; Reset Alarm Button / Jog Gate Open/Close; Programming - Maximum Controls MAX ARM Installation And Owner's Manual

additional features

open / stop / close inputs

The OPEN/STOP/CLOSE inputs will allow a standard 4-wire 3-Button Station
and a External Alarm RESET Button to be connected.
Corresponding LEDs will light when each button is activated.
External Alarm Reset Button
An external Alarm Reset button can to be installed in a secure
place and connected as shown to quickly SHUT-OFF a
sounding alarm. Otherwise alarm can be shut-off by the
RESET ALARM button on the side of control box (see below).

reset alarm button / jog gate open/close

C
o
n
t
B r
o o
x
l

programming

BATTERY
BATTERY VOLTAGE
INPUT
ERROR
E 1/2 F
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY BATTERY
CLOSED
TEST
POWER /
SOLAR IN
POWER
ERD SENSITIVITY
14 12 14
16
16
PROGRAM button
MIN MIN
ERD
1 9 1
MAX MOTOR MAX
MODULE
SENSE OVER SENSE
PORT 3 7 3
LOAD
OPENING CLOSING
OBD PORT
BLACK BOX
MAXIMUM CONTROLS M CONTROLS
RESET
OFF
DSP ARM CONTROLLER P ARM CONTROLLER
1
2
ALARM 3
4
5 PROGRAMMING MOTION CONTROL
ID PLUG
6
ERROR
1
2
3
ID
4
PLUG 5
6
7 OPEN EN STOP STOP
PROGRAM
8
9
10
OFF
ANTI-
EXIT PWR
TAILGATE
SOLAR MODE
EXIT LOOP
OFF ON
GND
OFF ON
CENTER LOOP
LOOP PWR CLOSING GATE SPEED
SAFETY LOOP OPERATOR
MIN
FAULTS
MAX
SINGLE DUAL
24VDC OUTPUT
GND MOTOR 1
12VDC OUTPUT
GND
Press and hold PROGRAM button for 5 seconds
to enter program mode.
MAX Arm/Ultra Arm V1
Reset Alarm Button:
If the Alarm Sounds During Normal Gate Operation:
obstructions before completing a gate cycle, the alarm will sound and the gate will PAUSE in the
position where the second obstruction occurred.
CHECK THE GATE AREA FOR ANY PROBLEMS BEFORE pressing the alarm reset button on the
control box to shut off the alarm and reset the gate.
NOTE: Alarm will automatically shut-off after five minutes but will not allow gate to operate until the
alarm reset button is pressed.
R M
L A
T A
S E
R E
Jog Gate Open/Close:
A T E S E
L O
G G
/ C
J O
E N
O P
The JOG key switch can open or close the gate electronically. Insert key on control box, turn and
HOLD (in either direction) to MOVE gate. Jog switch will operate BOTH arms together for bi-parting
gates. NOTE: OWNER of the gate operator is responsible for the KEY availability.
JOG buttons on circuit board function the same as JOG key switch.
CAUTION: Keep pedestrians and vehicles clear
of the gate while it is moving.
DSP ARM CONTROLLER
MOTOR 1 [+]
INPUTS [-]
[+]
MOTOR 2
INPUTS [-]
LIMIT 1
MOTOR 1
LIMIT 2
LIMIT 1
MOTOR 2
CLOSE
LIMIT 2
TIMER
12
ERD
9
MOTOR
LIMIT 1 LIMIT 1
OVER
7
MIN MIN MAX MAX MOTOR 1 MOTOR 1
LOAD
GND GND
OFF OFF
LIMITS LIMITS
LIMIT 2 LIMIT 2
LIMIT 1 LIMIT 1
MOTOR 2 MOTOR 2
GND GND
LIMITS LIMITS
LIMIT 2 LIMIT 2
ON/OFF ON/OFF
BATTERY BATTERY
JOG GATE OPEN GATE OPEN
COM COM
GATE CLOSED GATE CLOSED
GND GND
OPEN OPEN CLOSE CLOSE
CLOSE CLOSE NO NO
MAG MAG
LOCK LOCK
CO COM
NC
PUSH PULL MAGLOCK
OPEN OPEN DELAY
OPEN ONLY NC
PHOTO CLS NC
GATE
OFF 2.5 sec OPEN / CLS NC
1.5 sec
12VDC OUT
MIN
GND
OPEN ONLY 10K
MAX UL
ENTRAP
CLS ONLY 10K
MOTOR 2
OPEN / CLS 10K
12VDC OUT
GND
3-Button
Station
OPEN
STOP STOP
Com
CLOSE
Com
When the gate encounters TWO consecutive
Next Back
MOTION CONTROL
OPEN CLOSE
STOP
Programming Assistant Buttons
To enter PROGRAM mode, press and hold PROGRAM button for 5 seconds.
Follow instructions on-screen using the 4 buttons shown above to program
with. Press ONLY PROGRAM button again to end programming when finished.
In PROGRAM mode, you can do the following:
• Scroll through most recent errors.
• View input voltage (DC voltage).
• View average current gate consumption.
• View cycle count.
• Program date and time.
• Turn on/off other advanced features.
BATTERY
INPUT BATTERY VOLTAGE
ERROR
E 1/2 F
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE
IN USE
OPEN
REPLACE
LEAVE
BATTERY BATTERY
CLOSED
POWER / TEST
SOLAR IN
POWER
ERD SENSITIVITY
14 12
16
MIN
ERD
1 9
MOTOR
MODULE MAX MAX
SENSE OVER SENSE
PORT 3 7
LOAD
OPENING
OBD PORT
BLACK BOX
MAXIMUM CONTROLS
OFF
DSP ARM CONTROLLER
1
PROGRAMMING MOTION CONTROL
OPEN
PROGRAM PROGRAM
10
ANTI-
EXIT PWR
TA TAILGATE
SOLAR MODE SOLAR MODE
EXIT LOOP
OFF OFF
GND
S OFF ON ON
E S CENTER LOOP
LOOP PWR CLOSING CLOSING GATE SPEED
P R
OPERATOR
LOOP MIN MIN
MAX
SINGLE DUAL
T
S E
GND GND MOTOR 1
R E
12VDC OUTPUT 12VDC OUTPUT
GND ND
t o
External Alarm
Reset Button
JOG
OPEN CLOSE
Up Down
JOG
OPEN CLOSE
DSP ARM CONTROLLER
MOTOR 1 [+]
INPUTS [-]
[+]
MOTOR 2
OPEN
[-]
INPUTS
1 TIME
LIMIT 1
MOTOR 1
LIMIT 2
LIMIT 1
MOTOR 2
CLOSE LIMIT 2
TIMER
14 12
16
MIN ERD
1 9
MOTOR
OVER LIMIT 1
3 7
LOAD MIN MAX MOTOR 1
GND
CLOSING OFF
LIMITS
LIMIT 2
LIMIT 1
MOTOR 2
GND
LIMITS
ON/OFF LIMIT 2
BATTERY
JOG
GATE OPEN
COM
GATE CLOSED
GND
OPEN CLOSE
STOP CLOSE NO
MAG
LOCK COM
NC
PUSH PULL MAGLOCK
OPEN OPEN DELAY
OPEN ONLY NC
ON
PHOTO CLS NC
GATE
OFF 2.5 sec OPEN / CLS NC
1.5 sec 12VDC OUT
MIN M
GND
MAX MAX OPEN ONLY 10K
UL
ENTRAP
CLS ONLY 10K
MOTOR 2 MOTOR 2
OPEN / CLS 10K
12VDC OUT
GND
35