Relay Output Devices; Relay Device Basics; 4204 Relay Modules; 4204 Setup - ADEMCO VISTA-10SE Installation Instructions Manual

Relay Device Basics

4204 Relay Modules

Programming Options Defined

www.PDF-Zoo.com
Section 6. RELAY OUTPUT DEVICES
Relays are programmable switches that can be used to perform many different
functions. They can be used to turn lights on and off, control sounders, or for
status indications. In this system, each relay must be programmed as to how
to act (ACTION), when to activate (START), and when to deactivate (STOP).
Each of these is described below, and in the programming procedure for 80
and 81 interactive modes that are provided at the end of this section.
The control supports a total of 4 output relays.
The 4204 Relay modules provide Form C (normally open and normally
closed) contacts.
In 80 and
entries for programming of the Relay outputs used in the system. Refer also to
"OUTPUT RELAY DEVICE WORKSHEET FOR 80 AND 81 INTERACTIVE
MODES" in the blank programming form provided in the separate
Programming Guide manual.

4204 Setup

The 4204 unit can be mounted either remotely or in the control panel. The
following steps should be taken to properly set up the 4204:
1. Connect the 4204 to the control's remote keypad terminals (4–7), using
the con nector supplied with the 4204. Use standard 4-conductor twisted
OFF ON
cable for long wiring runs.
@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ e ? @ @ h ? @ @ @ @ @ @ @ @ @ @ @ @
@ @ h ? @ @ h ? @ @ @ @ 2. Set the 4204's DIP switch for a device address of "1" (switch 2 "OFF"
@ @ h ?
@ @ h ? @ @ h ? @ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @
@ @ @ @ @ @ @ @ and switches 3, 4, and 5 "ON"). Switch 1 determines the unit's cover
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ tamper response ("ON" = disabled, "OFF" = enabled).
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ 3. Connect the desired field wiring to the unit's relay contact terminals. See
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ g ? @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ g ? @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @
Figure 9.

Supervision

4204 modules are supervised against removal. CHECK and zone 09 will be
displayed if a module is disconnected from the control's keypad terminals (4,
5, 6, & 7).
4204
COVER TAMPER (REED) SWITCH
The following will help you understand the programming of OUTPUT RELAYS
when using
relays are described below, followed by the actual screen prompts and
available entries.
firealarmresources.com
81 interactive modes, a series of keypad prompts will request
4204
DIP SWITCH
FOR SETTING DEVICE ADDRESS
AND ENABLING/DISABLING TAMPER
4-PIN CONSOLE PLUG
EITHER OR BOTH
CAN BE USED
TB1
13 14 15 16

Figure 9. 4204 Connections to Control

80 and 81 modes. The options used to start and stop these
– 39 –
RELAY 4
TYPICAL
(SHOWN "OFF")
RELAY
3
RELAY
2
RELAY
1
YEL
DATA IN
FROM CONTROL
BLK
(–) GROUND
GRN
DATA OUT
TO CONTROL
RED
(+) 12V
C
NC
NO
C
NC
NO
C
NC
NO
C
NC
NO
TB2