Section 6. Relay Output Devices; Relay Device Basics; 4204 Relay Modules; 4204 Setup - ADEMCO N7227V5 Installation Instructions Manual

Section 6. RELAY OUTPUT DEVICES

Relay Device Basics

4204 Relay Modules

4204 Setup

OFF ON
@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @
@ @ h ? @ @
@ @ h ? @ @ h ? @ @ @ @
@ @ h ? @ @
@ @ h ? @ @ h ? @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ g ? @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ g ? @ @
@ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @

Supervision

Programming Options Defined

Relays are programmable switches that can be used to perform many different
functions. They can be used to turn lights on and off, control sounders, or for
status indications. In this system, each relay must be programmed as to how
to act (ACTION), when to activate (START), and when to deactivate (STOP).
Each of these is described below, and in the programming procedure for 80
and 81 interactive modes that are provided at the end of this section.
The control supports a total of 4 output relays.
The 4204 Relay modules provide Form C (normally open and normally
closed) contacts.
In 80 and 81 interactive modes, a series of keypad prompts will request
entries for programming of the Relay outputs used in the system. Refer also to
"OUTPUT RELAY DEVICE WORKSHEET FOR 80 AND 81 INTERACTIVE
MODES" in the blank programming form provided in the separate
Programming Guide manual.
The 4204 unit can be mounted either remotely or in the control panel. The
following steps should be taken to properly set up the 4204:
1. Connect the 4204 to the control's remote keypad terminals (4–7), using
the connector supplied with the 4204. Use standard 4-conductor twisted
cable for long wiring runs.
2. Set the 4204's DIP switch for a device address of "1" (switch 2 "OFF"
and switches 3, 4, and 5 "ON"). Switch 1 determines the unit's cover
tamper response ("ON" = disabled, "OFF" = enabled).
3. Connect the desired field wiring to the unit's relay contact terminals. See
Figure 9.
4204 modules are supervised against removal. CHECK and zone 09 will be
displayed if a module is disconnected from the control's keypad terminals (4,
5, 6, & 7).
4204
DIP SWITCH
FOR SETTING DEVICE ADDRESS
AND ENABLING/DISABLING TAMPER
COVER TAMPER (REED) SWITCH

Figure 9. 4204 Connections to Control

The following will help you understand the programming of OUTPUT RELAYS
when using 80 and
relays are described below, followed by the actual screen prompts and
available entries.
– 39 –
4204
RELAY 4
TYPICAL
(SHOWN "OFF")
4-PIN CONSOLE PLUG
EITHER OR BOTH
CAN BE USED
TB1
13 14 15 16
YEL
DATA IN
FROM CONTROL
BLK
(–) GROUND
GRN
DATA OUT
TO CONTROL
RED
(+) 12V
81 modes. The options used to start and stop these
C
NC
NO
C
RELAY
3
NC
NO
C
RELAY
2
NC
NO
C
RELAY
1
NC
NO
TB2