Seco EASYSHRINK EVO User Instructions page 4

IMPORTANT
CAUTIONS & WARNINGS
The Easyshrink Evo is built
with the latest technology and
it is extremely safe and easy to
operate.
However, there is still some
danger if this device is operated
incorrectly and/or by untrained
personnel.
Pay particular attention to the
following cautions and warnings
marked with the "Attention" and
"Danger" symbols.
Failure to follow safe operating
practices may cause injuries,
death or damage to the
device and may VOID your
manufacturer's warranties.
WARNING
▪
Before attempting to use the
device, you must read and
fully understand this User
Guide. Keep this User Guide
within easy reach of operating
personnel.
▪
Visually inspect the device,
power cord and accessory
items for any signs of wear or
damage before operating the
device. Do not use the device if
there is any sign of damage or
if the device is not performing
normally.
▪
Never operate the device
without the correct induction
heat-focusing stopper in place
on the induction head. Do not
allow any part of the induction
head to contact the tool
holder or cutting tool during
operation or damage to the
device may occur.
▪
The holder and the tool must
be clean, free from grease and
dry before being fitted to the
device.
4
▪
Tool shank tolerance required:
Ø3 to 5 mm (Ø0.118" to
0.1968") maximum h5.
Tool shank must be carbide or
heavy metal (e.g. Densimet).
Ø6 to Ø32 mm (Ø0.236" to Ø
1.25") maximum h6.
Tool shank can be steel, HSS,
carbide or heavy metal.
Using h5 for Ø6 to Ø32
mm (Ø0.236" to Ø1.2598")
provides a safer minimum
clamping torque.
▪
Do not wear rings, bracelets
or other metallic objects
while operating the device.
Metallic objects may heat
up very quickly when near
the induction head during
operation.
▪
Use the provided heat-resistant
gloves and pliers whenever
handling tools or tool holders.
Never try to handle hot tools or
tool holders until the cooling
cycle is complete.
▪
If the device is moved from a
cold environment to a warm
one, wait three hours before
operating to prevent build-up
of condensation and electronic
system errors.
▪
Persons with pacemakers fitted
may not operate the device and
must maintain a minimum safe
distance of 2 meters (6 feet)
from the device at all times.
▪
Cutting tools have sharp edges.
Handle with caution.
WARNING
Electric shock risk
▪
The power cord provided
must be plugged into the
correct standard, three-phase
outlet for your country.
Operating the device while it
is improperly connected or at
the wrong voltage may damage
the device and could cause
death or injury.
▪
Position the power cord so that
it cannot be damaged by fork
trucks or other equipment or
cause a tripping hazard for
personnel.
▪
Do not operate the device
in a wet environment where
exposure to coolant or spills
are likely to occur. Electric
shocks or damage to the device
may occur.
▪
Never operate the device
around flammable materials or
fumes. Do not use flam-
mable liquids or aerosols to
clean the tool holders. Never
expose the device or hot tools
to combustible materials.
▪
Never open the device or
attempt repairs or you will
VOID the manufacturer's
warranty. There is dangerous
residual voltage inside that
may cause death or injury.
▪
Unauthorized modifications
or changes to the Shrinkfit
Evo device will VOID your
manufacturer's warranty. Do
not try and service your device
yourself. After-sales techni-
cians can provide any
necessary repairs or
maintenance. Do not modify
or disable the built-in safety
features of the device.
▪
Turn off the power switch
and disconnect the power
cord from the outlet before
cleaning, servicing or storing
the device.