Single board computer with intel atom x series, intel celeron j / n series, intel pentium n series (formerly apollo lake) processors on picoitx form factor (68 pages)
Page 1
TANARO core Cortex -A53 Single Board Computer ® ® High performance with low power consumption: Designed for demanding industrial performance requirements and AV applications with integrated wireless connectivity Product Manual...
Page 2
The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. Revision Date Author Description 19.09.2021 Initial Release 17.12.2021 SECO CI Update 2022 Online support on edge.seco.com...
TANARO core Introduction Thank you very much for purchasing a SECO Northern Europe product. Our products are dedicated to professional use and therefore we suppose extended technical knowledge and practice in working with such products. The information in this manual is subject to technical changes, particularly as a result of continuous product upgrades.
Please read this section carefully and observe the instructions for your own safety and correct use of the device. Observe the warnings and instructions on the device and in the manual. SECO Northern Europe embedded systems have been built and tested by us and left the company in a perfectly safe condition.In order to maintain this condition and ensure safe operation, the user must observe the instructions and warnings contained in this manual.
Page 6
2 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The outside of final products containing the TANARO module must display in a user accessible area a label referring to the enclosed transmitting module. This exterior label can use wording such as the following12: “Contains Transmitter Module FCC ID: (insert the modules FCC ID) ”...
„Annex A: Hardware Revision Information“: Please find the hardware version grid in TANARO is an Embedded System to be used as human machine interface (HMI) in various applications. Please refer to Annex „C-2 Field of Application“ for further information. The system is equipped with a large number of industrial interfaces.
PRODUCT MANUAL TANARO core Related Documents and Online Support This document contains operating system specific information. The following additional documentations are available: OPERATING SYSTEMS Contains information about Linux BSP with development environment Linux Yocto Dunfell Linux Embedded System Yocto (Codename: Dunfell, Version X) includes first information about the bootloader Flash-N-Go https://bit.ly/3y3xEuB...
PRODUCT MANUAL TANARO core Technical Data CPU Type i.MX8M Mini Quad Core Class Cortex -A53 ® ® Core Clock 1,8 GHz Media Processing Engine (MPE) with NEON technology for SIMD: Floating Point Unit (FPU) Support of 64-bit Arm®v8-A architecture A53: 32 KB L1 cache for instruction and 32 KB for data M4: 16 KB L1 cache for...
PRODUCT MANUAL TANARO core Connectors As this manual describes a core version, the internal and external interfaces will be mentioned in the following chapter. (Exemplary Illustration front side. The illustration shows the fully equipped TANARO Quadcore. Pos. Description Pos. Description...
Installation and Start Up The content of this document is limited to explain the device connectors and how to access TANARO via FTP over your local area network (LAN) within a few seconds. For advanced hardware specifications and software support, please refer to chapter „3.2 Related Documents and Online Support“...
PRODUCT MANUAL TANARO core Internal and External Interfaces Gigabit Ethernet (U16) Name Description Information TX+/TD0+ TX-/TD0- RX+/TD1+ Rx/Tx might be swapped TD2+ (Auto-MDIX) +/- might be swapped TD2- (Autom. polarity correction) RX-/TD1- TD3+ TD3- Header: RJ45 LED on the left (link) is default off and turns on when link is detected.
PRODUCT MANUAL TANARO core Power (J9) Name Description Level DC Ground Vcc_In DC Input voltage Nom. 9 to 32 V DC Header: Molex 43045-0200 Micro-Fit 2p Plug: Molex 43025-0200 Micro-Fit 2p, crimp contact Molex 43030-0007 Shielding with 6,3 mm male spade terminal connector.
PRODUCT MANUAL TANARO core CAN/RS-485 Interface (J12) This connector can be configured to your needs in following combinations: CAN/RS-485; 2x RS-485; CAN/UART Name Description Level GND_CAN_RS485 Ground for CAN and RS485 group CAN1_TERM To enable CAN1-Termination, bridge with CAN1_H CAN1_H...
PRODUCT MANUAL TANARO core USB Host 1 (J7) Name Description Level USB_H1_VBUS Power supply +5 V DC max 500mA USB_H1_DN Data minus (D-) USB_H1_DP Data plus (D+) Ground Header: USB Type A USB Host 2 (J6) Name Description Level USB_H2_VBUS...
PRODUCT MANUAL TANARO core 6.10 USB OTG (J5) Name Description Level USB1_VBUS Power supply +5 V DC max 500mA USB1_DN Data minus (D-) USB1_DP Data plus (D+) USB1_ID Device ID Ground Header: Micro-USB Type AB 6.11 USB OTG Host (J3)
PRODUCT MANUAL TANARO core 6.13 Power LED (D36) Should be green if the device is powered up. 6.14 Status LED (D22) Should blink when device is active 6.15 Bootselect Switch (SW2) Push during a power on sequence to boot into the secondary OS.
PRODUCT MANUAL TANARO core 6.23 Backlight (J15) Name Description Level 12 V Supply; only for X1 Supply 12 V 12V +-2% max 3 A >12.5V 12 V Supply 5V +-3% max 3 A Ground Ground Ground Typ. 250Hz 16 Bit 3.3 V...
PRODUCT MANUAL TANARO core 6.29 PCIe Half Mini Connector (XU20) Name Description Level WAKE# PCIE Wake 3.3V Supply 3.3 V Reserved not connected Ground Reserved not connected 1.5V Supply 1.5 V CLKREQ# not connected UIM_PWR SIM Card Interface Ground UIM_DATA...
TANARO core Battery Battery Specifications The internal baseboard is equipped with a Primary Lithium battery (type CR1220), which has a typical lifetime of 8 years. Type SECO Northern Europe Article Number Battery type CR1220 010-0091R Battery type CR1220 010-0059R Manufacturer Model Alpha 3 Manufacturing Ltd.
PRODUCT MANUAL TANARO core Replacement of the Internal Battery The internal battery is placed as per figure below. The device shall be handled by authorized and skilled personnel only. Danger of electric hazard! First before removing battery, please make sure that the unit is completely disconnected from any power supply, direct or indirect.
This document is applicable for all products listed below. Please note that customized variants might possibly not support all features listed herein. Additional features are documented in specific attachments. Platform Article Number Marking on PCB TANARO core S 900-4475R 0774 TANARO V1.1 TANARO core M 0774 TANARO V1.1...
Supplier Declaration – Directive EG 1907/2006 REACH SECO Northern Europe is manufacturer of electronic products, thus - in the sense of REACH - we are so called „downstream users“. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance.
These solutions are offered exclusively as OEM products. They do not include any application software that is intended for the end user. Therefore, we do not make any EU declarations of conformity in the name of SECO Northern Europe GmbH and do not provide the products with the CE mark.
The outside of final products containing the TANARO module must display in a user accessible area alabel referring to the enclosed module. This exterior label can use wording such as the following12: “Contains Transmitter Module FCC ID: tbd”...
If the product has been returned with or without prior notice and no failure or malfunction can be detected or the failure or malfunction is caused by inappropriate handling or the device has been returned after expiry of warranty period, SECO Northern Europe reserve the right to charge the user for repair or replacement.
If you intend to use these products in applications as quoted in (II) we highly recommend a personal contact with our consultants and/or technical sales team. (I) Recommended application areas for SECO Northern Europe embedded systems Even for these applications, we recommend to get in contact with our technical sales team. We offer a wide range of support, even at an early stage of evaluation and/or design-in phase.
TANARO core Annex D: Technical Support Before contacting the SECO Northern Europe support team, please try to help yourself by the means of this manual or any other documentation provided by SECO Northern Europe or the related websites. If this does not help at all, please feel free to contact us.