Yamaha 01V Owner's Manual page 294

284
MIDI Data Format
PARAMETER CHANGE (type operation for type
0x03:controller(LCD-Fader mode))
Reception
When [Parameter Change RX] is ON and the [Rx CH] matches the
Device Channel included in the SUB STATUS, the message will be
received.
When [Parameter Change ECHO] is ON, this message will be ech-
oed.
When this message is received, the LCD screen, the corresponding
Fader Mode, and the specified channel will be selected.
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUOP ID 00111110 3e
MODEL ID 00000100 04
PARAM TYPE 01000011 03
DATA 00000001 01
0ddddddd dd
0ddddddd dd
0000dddd dd
EOX 11110111 F7
PARAMETER CHANGE (bit operation for type
0x43:controller(key remote))
Reception
When [Parameter Change RX] is ON and the [Rx CH] matches the
Device Channel included in the SUB STATUS, this message will be
received.
When [Parameter Change ECHO] is ON, this message will be ech-
oed.
When this message is received, the same processing will be performed
as when the specified key (refer to the table below) is pressed
(released).
Transmission
When [Parameter Change ECHO] is ON, this message will be trans-
mitted without change.
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUOP ID 00111110 3e
MODEL ID 00000100 04
PARAM TYPE 01000011 43
DATA 00000000 00
0ddddddd dd
0000dddd dd
:
EOX 11110111 F7
KEY key no.bit0 bit1 bit2 bit3
-------------------------------------------------------------------------------------------------------------------------------------------------
key1 0 ON1 ON2 ON3 ON4
key2 1 ON9 ON10 ON11 ON12
key3 2 SOLO1 SOLO2 SOLO3 SOLO4
key4 3 SOLO9 SOLO10 SOLO11 SOLO12
key5 4 SEL1 SEL2 SEL3 SEL4
key6 5 SEL9 SEL10 SEL11 SEL12
key7 6 ONRTN1 ONRTN2 SOLORT1 SOLORT2 SELRTN1 SELRTN2
key8 7 AUX1 AUX2 AUX3 AUX4
key9 8 LOW L-MID H-MID HIGH
key10 9 UP LEFT RIGHT DOWN
key11 10 DYNAMIX EQ DELAY PAN
key100 99 FRZ-REC FRZ-PLAY ------ ------
key101 100 SOLO1 SOLO2 SOLO3 SOLO4
key102 101 SOLO9 SOLO10 SOLO11 SOLO12
key103 102 SOLO17 SOLO18 SOLO19 SOLO20
* Normally, data should be transmitted as "set(bit3=1)." In this case,
the 01V will determine that that switch has been pressed and then
immediately released, and will perform the appropriate processing.
This means that you will not have to transmit "reset(bit3=0)" sepa-
rately.
* The keys followed by 100 are virtual key, it would be the keys on
LCD.
01V—Owner's Manual
System Exclusive Message
Manufacturer's ID No.(YAMAHA)
parameter change n=0-15(Device Chan-
nel No.1-16)
MODEL ID
Device code (01V)
controller (type)
control No.(LCD-Fader mode)
channel select(0-30)
LCD select No.(0-17)
PAGE No.(0-4)
End Of Exclusive
System Exclusive Message
Manufacturer's ID No.(YAMAHA)
parameter change n=0-15(Device Chan-
nel No.1-16)
MODEL ID
Device code (01V)
controller
control no.(0:key remote)
No. 0-10,99-102(key 1-11,100-103)
data(bit0-2:change bit no.0-7,
bit3:0=reset 1=set)
:
End Of Exclusive
bit4 bit5 bit6 bit7
ON5 ON6 ON7 ON8
ON13-14 ON15-16 ONSTOUT ------
SOLO5 SOLO6 SOLO7 SOLO8
SOLO13-14SOLO15-16 ------ ------
SEL5 SEL6 SEL7 SEL8
SEL13-14 SEL15-16 SEL STO ------
HOME MEMORY
EFFECT1 EFFECT2 OPTION REMOTE
------ ------ ------ ------
ENTER INC DEC ------
UTILITY MIDI SETUP VIEW
------ ------ ------ ------
SOLO5 SOLO6 SOLO7 SOLO8
SOLO13-14SOLO15-16 SOLO-RTN1 SOLO-RTN2
SOLO21 SOLO22 SOLO23 SOLO24
PARAMETER CHANGE (type 0x04:multiple linking)
This message is valid only for the connector that has been specified as
the LINK PORT.
When two '01V' units have been connected by a cable, some of the
functions (refer to the following table) will be linked.
The same LINK PORT connector settings must be made on both
units.
Reception
This message is always received, and will execute the LINK function
(refer to the following table). (This is not dependent on
MIDI-SETUP.)
Transmission
This message is transmitted when LINK-related functions (refer to
following table) are performed. (This is not dependent on
MIDI-SETUP.)
When [Parameter Change ECHO] is ON, this message is transmitted
without change.
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUOP ID 00111110 3e
MODEL ID 00000100 04
PARAM TYPE 00000100 04
DATA 0mmfffff mf
0ddddddd dd0
0ddddddd dd1
: :
EOX 11110111 F7
Status Function Note
----------------------------------------------------------------------------------------------------------
0x00 scene recall Recall the specified memory number
0x01 scene store Store to the specified memory number with title
(Assign the same title to all)
0x02 scene title edit If the title was modified, make it the same, make it
match
0x48 solo mode Match the solo mode
bit6: enable/disable
bit5: on/off
bit2: recording/mixdown
bit1: sel mix/last
bit0: after fader/pre fader
0x60 display call When the screen (Fader Mode) is changed, make it
match
0x61 metering point Make the meter points match
0x62 peak hold Make the meter Peak Hold ON/OFF match
System Exclusive Message
Manufacturer's ID No.(YAMAHA)
n=0-15(Tx/Rx Channel No.1-16)
MODEL ID
Device code (01V)
multiple linking
data format (bit6-5:status, bit4-0:contents)
data #0
data #1
End Of Exclusive