Icom IC-FR6000 Service Manual Addendum page 249

6-3 TRANSMIT ADJUSTMENT (continued)
1) Select an adjustment item using cursor or [↑] / [↓] keys of the PC's keyboard.
2) Set or modify the adjustment value as specifi ed using [←] / [→] keys of the PC's keyboard, then push the [ENTER] key.
ADJUSTMENT
ADJUSTMENT
CONDITION
ANALOG 1
DEVIATION
-Preparation-
2
3
-Adjust- 4 • CH. : 1-10
• Transmitting
(Wide)
(Middle) 5 • CH. : 1-11
<[FR6100] only> • [Wide Band
Width] : "Middle"
(see the page 6-4)
• Transmitting
(Narrow) 6 • CH. : 1-12
• Transmitting
CTCSS/DTCS 1
DEVIATION
-Preparation-
-Adjust- 2 • CH. : 1-19
• Transmitting
6-4 RECEIVE ADJUSTMENT
1) Select an adjustment item using cursor or [↑] / [↓] keys of the PC's keyboard.
2) Set or modify the adjustment value as specifi ed using [←] / [→] keys of the PC's keyboard, then push the [ENTER] key.
ADJUSTMENT
ADJUSTMENT
CONDITION
RECEIVE 1
SENSITIVITY
2
-Preparation-
-Adjustment- 3 • CH. : 1-23 [Low]
(Band center)
• Receiving
-Adjustment- 4 • CH. : 1-24
(Band center)
For [Low band] • Receiving
version only
-Adjustment- 5 • CH. : 1-22 [Low]
(Band high)
• Receiving
• Set the item [TX Mode] to "1."
–
1) Connect a Modulation Analyzer to the TX
antenna connector through an attenuator.
2) Set the Modulation Analyzer as;
– HPF
LPF
De-emphasis : OFF
Detector
1) Connect an Audio Generator to the MIC
line through the JIG cable.
2) Set the Audio Generator as;
–
Modulation
Level
Wave form
1) Adjust the deviation using [←] / [→] keys
of the PC's keyboard.
2) Push the [ENTER] key to store the adjust
value.
• Set the item [TX Mode] to "3."
–
1) Adjust the deviation using [←] / [→] keys
of the PC's keyboard.
2) Push the [ENTER] key to store the adjust
value.
– • Set the item [RX Mode] to "1."
1) Connect an SSG to the RX antenna
connector.
2) Set the SSG as;
–
Level
Modulation
Deviation
1) Set the SSG as;
: 1-23 [High] Frequency
2) Select the item [BPF C ALL], then push
the [ENTER] key.
1) Set the SSG as;
[Low] only Frequency
2) Select the item [BPF L ALL], then push
the [ENTER] key.
1) Set the SSG as;
: 1-24 [High] Frequency
2) Select the item [BPF H ALL], then push
the [ENTER] key.
OPERATION
: OFF
: 20 kHz
: (P-P)/2
: 1 kHz
: 40 mV rms
: Sine wave
OPERATION
: +20 dBμ
: 1 kHz
: 3.5 kHz
: 435.000 MHz [Low]
450.100 MHz [High]
375.000 MHz [FR6000-L]
: 400.100 MHz [Low]
350.100 MHz [FR6000-L]
: 469.900 MHz [Low]
519.900 MHz [High]
399.900 MHz [FR6000-L]
6 - 9
ADJUSTMENT
VALUE
ITEM
[TX Mode]
–
–
[MOD (Wide)] ±4.05–4.15 kHz
[MOD (Middle)] ±3.15–3.25 kHz
[MOD (Narrow)] ±2.05–2.15 kHz
[TX Mode]
[CTCSS] ±0.68–0.72 kHz
ADJUSTMENT
VALUE
ITEM/POINT
[RX Mode]
–
[BPF C ALL]
(Automatic
[BPF L ALL]
adjustment)
[BPF H ALL]
"1"
–
–
"3"
"1"
–