[Event Prog] Create Event Programs For An Event Occurrence; Vmd; Adm (Activity Detection Mode); Alm (Alarm Mode) - Panasonic WJ-HD316 Operating Instructions Manual

The following are for the recording rate. When OFF is
selected, images from the selected camera channel will not
be recorded.
OFF/0.1 ips/0.2 ips/0.3 ips/0.4 ips/0.5 ips/1 ips/2 ips/3 ips/5
ips/6 ips/7.5 ips/10 ips/15 ips/30 ips/60 ips
AUTO: Recording rate will be set automatically. (Not possi-
ble for event pre-recording and event post-recording)
Important:
The total recording rates of each camera channels in the
same recording mode must be less than the recording rate
as described in "Recording Rate for Each Recording Mode"
above.
Examples: When selecting "FIELD" for resolution, "15 ips" for
manual recording, "15 ips" for scheduled recording, "30 ips"
for event recording:
Total recording rates of CAM 1 - 16 (manual recording):
less than 15 ips
Total recording rates of CAM 1 - 16 (scheduled recording):
less than 15 ips
Total recording rates of CAM 1 - 16 (event recording): less
than 30 ips
When the total recording rates becomes more than the set
value, the recording mode table will turn red.
Recording mode table
The larger total recording rates between recording rates of
event pre-recording and recording rates of event post-
recording for each camera channel must be less than the
recording rate as described in "Recording Rate for Each
Recording Mode" above.
The following are available for image quality.
SFA/SFB: Top quality (SUPER FINE)
FQA/FQB: High quality (FINE)
NQA/NQB: Standard quality (NORMAL)
EXA/EXB: Low quality (EXTENDED)
**A is suitable for less dynamic images.
**B is suitable for more dynamic images.
The following are available for recording duration (only
event pre-recording and event post-recording).
1 s - 10 s (in 1 second intervals)
20 s/30 s/1 - 10 m (in 1 minute intervals)
20 - 60 m (in 10 minutes intervals)
MANUAL: Recording duration will be as follows depending
on the event type.
• At a motion detection: For 8 seconds
• At a video loss occurrence: During a video loss occur-
rence
• At a terminal alarm occurrence: During the supply of a
signal
• At a command alarm: For 8 seconds
CONTINUE: Recording will be performed continuously
until the [ALARM RESET] button is pressed.
w [Event Prog] Create event programs
for an event occurrence
Perform the settings of event action for each event type
(motion detection, video loss, terminal/command alarm)
or of auto copy.
SETUP MENU
Maintenance Recording
Switcher Display
Event Program 1
Time Table
Event Program 2
REC Prog
Event Program 3
Event Prog
Event Program 4
Special Days
SETUP MENU
Maintenance Recording
Switcher Display
Event Program 1
Time Table
Event Program 2
REC Prog
Event Program 3
Event Prog Event Action 4
Event PROG1
Special Days

VMD

Video Loss
Terminal/Command Alarm
VMD
Perform the settings of event action at a motion detection or
the settings of the auto copy function.
SETUP MENU
Maintenance Recording
Switcher Display
Event Program 1
Time Table
Event Program 2
REC Prog
Event Program 3
EVT Prog
Event Program 4
VMD
Special Days
Action Mode
Auto Copy
Perform the settings for the following action mode. Refer to
page xx for further information about each action mode.
ADM (Activity Detection Mode): Performs only recording,
writing an event log and camera movement to a preset
position at an event occurrence. Other event actions
will not be performed.
ALM (Alarm Mode): Performs every event action according
to the settings.
Auto copy is the function to copy recorded images auto-
matically onto the copy area of the hard disk or the DVD-
RAM disk.
Select ON or OFF to enable or disable the auto copy func-
tion.
ON: Enable the auto copy function
OFF: Disable the auto copy function
Event Schedule
LIVE
Com System
SETUP
SETUP
SETUP
SETUP
Event Schedule
LIVE
Com System
SETUP
SETUP
SETUP
SETUP
SETUP
SETUP
SETUP
O K CANCEL
Event Schedule
LIVE
Com System
SETUP
SETUP
SETUP
SETUP
ALM
OFF
OK CANCEL
99