Operating Instructions; Boxing In; Door Reversal; Panel Changing - Vitrifrigo Trivalente Series User, Maintenance And Installation Manual

User, Maintenance and Installation Manual - Trivalenti

Operating Instructions

!
Follow the instructions below with great care.
It is strictly forbidden to install the refrigerator using
different methods to those described in this manual, or
persons who have not been authorised by Vitrifrigo srl.
To avoid possible damage, only insert screws in the
relevant holes provided on the refrigerator.
Make sure that electrical cables are adequately protected
- especially the power cables - in order to avoid them
coming into contact with hot or sharp parts.
Vitrifrigo snc refuses to accept any liability for installations
carried out by personnel who have not been authorised by
the company itself.

BOXING IN

The refrigerator must be inserted into a compartment of adequate
dimensions (see Table 3) – without forgetting that there must be an all-
round gap of no more than 3 mm between the appliance and the
compartment. Ensure that the compartment is:
perfectly regular and with a flat bottom for problem-free appliance slotting in
or removal; sufficiently sturdy to sustain the weight of the refrigerator when
full, taking into account the stresses caused by the vehicle when it is in
motion.
Before inserting the refrigerator into the compartment, fix strips to the sides
"A" (as in Fig.4) using an elastic bonding agent.
Insert the appliance into the compartment, ensuring that it is perfectly
aligned and that nothing protrudes. Also make sure that there is a gap of 10-
20 mm between the vehicle wall and the refrigerator unit in order to permit
the correct ventilation of this latter (see Fig. 4).
Use screws to fix the refrigerator firmly to the sides of the compartment "A"
(as in Fig. 5). The screws should be suited to withstand strain, not forgetting
the stresses caused by the vehicle in motion and should be inserted in the
holes "B" made inside the unit (as in Fig.5). Use the cap supplied to close
the holes "C" (as in Fig. 5).

DOOR REVERSAL

To change the direction in which the appliance door opens, from right to left,
it is necessary to adjust the hinges "B" (Fig.1) and the doorstop "C" (Fig.1)
as follows: Disassemble the doorstop "C" by removing the screw "A" (see
Fig.5),
Loosen the screw pin "D" on the top hinge "B" (see Fig.5),
Move the door upwards until it comes away from the hinge.
Loosen the screw pin "D" on the bottom hinge "B" and screw it into the bottom
hinge on the opposite side, Reposition the door and screw the screw pin into
the top hinge on the opposite side, Replace the doorstop "C" and tighten into
place with the screw.

PANEL CHANGING

To disassemble and/or change the panel "A" (Fig.1), proceed as
follows:
Remove the door, as indicated in the previous section.
Loosen the screws on the lower base section and remove it.
Slide the panel out downwards.
Insert the new panel in place of the old one, sliding it upwards until the
stop.
Reassemble the lower base section.

ELECTRICAL CONNECTION

All cables must be inserted into the connectors "P" (Fig.1) as
shown in Fig.10, making sure that the screws are properly
tightened and ensuring that the connection has been made
perfectly.
Check that the voltage used corresponds to that printed on the
appliance rating label.
The connection between the refrigerator and the battery must be made
directly using a cable with a minimum section of 1.5 mm if the length of
the cable is less than 4 metres; 2.5 mm if the cable length is between 4
and 9 metres; 4 mm if the cable length is more than 9 metres.
WARNING: ALWAYS RESPECT POLARITY (for DC connections).
Power Supply (MAINS POWER)
Insert the power cables into the connector "1" (Fig.10). Use a cable with
a section of at least 1.5 mm Fit a differential thermomagnetic circuit
breaker in compliance with the standard and regulations in force.
Power Supply (BATTERY)
Power supply with double line (direct and switch block) (See
Fig.10-A)
Connect the direct power cable (respecting the polarities) to the
connector "3" and connect the power cable from the switch block
(respecting the polarities and sections as previously indicated), to the
connector "2"
Direct power supply: (see Fig.10-B)
Connect the power cable (respecting the polarities and sections as
indicated previously) to the connector "3". Connect the connector "5" to
connector "2" creating an electric jumper, using a conductor that has a
section of no less than 1.5 mm
Power Supply for the EXTERNAL FAN (optional)
Connect the fan power cable (respecting polarities) to the connector "4"
(Fig.10) using a cable with an adequate section for the power of the fan.
GAS CONNECTIONS
This refrigerator is able to operate using gas (propane or butane LPG).
The gas type and operating pressure must be the same as those
indicated in the box "7" (Fig.2) on the rating label "E" (Fig.1) inside the
refrigerator, or on the Conformity Declaration attached to this manual.
Installation must be carried out in accordance with the various
13