Scheppach SD1600V Translation Of Original Instruction Manual page 23

9. Use protective equipment
- Wear protective goggles.
- Wear a mask when carrying out dust-creating work.
10. Connect the dust extraction device
- If connections for dust extraction and a collecting
device are present, make sure that they are con-
nected and used properly.
11. Do not use the cable for purposes for which it
is not intended
- Do not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and sharp
edges.
12. Secure the workpiece
- Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held more
securely than with your hand.
13. Avoid abnormal posture
- Make sure that you have secure footing and al-
ways maintain your balance.
14. Take care of your tools
- Keep cutting tools sharp and clean in order to be
able to work better and more safely.
- Follow the instructions for lubrication and for tool
replacement.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
- Keep the handle dry, clean and free of oil and
grease.
15. Pull the connector out of the socket
- When the electric tool is not in use or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
16. Do not leave a tool key inserted
- Before switching on, make sure that keys and ad-
justing tools are removed.
17. Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
18. Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
19. Remain attentive
- Pay attention to what you are doing. Remain sen-
sible when working. Do not use the electric tool
when you are distracted.
20. Check the electric tool for potential damage
- Protective devices or other parts with minor dam-
age must be carefully inspected to ensure that
they function correctly and as intended prior to
continued use of the electric tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-free
operation of the electric tool.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
specialist workshop, insofar as nothing different
is specified in the user manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any electric tool on which the switch
cannot be switched on and off.
21. ATTENTION
- The use of other insertion tools and other acces-
sories can entail a danger of injury.
22. Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
WARNING
This electric tool generates an electromagnetic field
during operation. This field can impair active or pas-
sive medical implants under certain conditions. In or-
der to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
5.2 Special safety instructions
• In an emergency, switch the machine off directly
and pull out the mains plug.
• Observe all of these notes before and while work-
ing with the saw.
• Never use the saw to cut firewood.
• The machine is equipped with a safety switch
against reactivation if the voltage drops.
• If an extension cable is required, make sure that its
cross-section is sufficient for the current consump-
tion of the saw. Minimum cross-section 1.5 mm
• Only use cable reels in the unrolled state.
• Personnel working on the machine must not be dis-
tracted.
• Under no circumstances should the saw blades be
braked by pushing against the side after switching
off the drive.
• Only install saw blades that are well sharpened,
free of cracks and not deformed.
• Faulty saw blades must be replaced immediately.
• Do not use saw blades that do not correspond to
the characteristics specified in these usage instruc-
tions.
• Ensure that all devices that cover the saw blade
work properly.
• Safety equipment on the machine must not be dis-
assembled or made unusable.
• Damaged or faulty protective devices must be re-
placed immediately.
• Do not cut workpieces that are too small in order to
keep them secure in your hands.
.
2
GB | 23