Cmos Setup - VersaLogic Python EBX-11 Reference Manual

CMOS Setup

The default CMOS Setup parameters for the EBX-11 are shown below. See VersaLogic
Knowledgebase article
these parameters. Due to system configuration and changes between BIOS revisions, the
information on your monitor may differ from that shown above. The date shown on the Basic
CMOS Configuration screen is the BIOS build date.
+------------------------------------------------------------------------------+
|
| (C) 2005 General Software, Inc. All rights reserved
+---------------------------+--------------------+-----------------------------+
| DRIVE ASSIGNMENT ORDER:
| Drive A: (None)
| Drive B: (None)
| Drive C: Ide 0/Pri Master +--------------------+ Show "Hit Del"
| Drive D: (None)
| Drive E: (None)
| Drive F: (None)
| Drive G: (None)
| Drive H: (None)
| Drive I: (None)
| Drive J: (None)
| Drive K: (None)
| Boot Method: Boot Sector
+---------------------------+ Ide 0: 3 = AUTOCONFIG, LBA
| FLOPPY DRIVE TYPES:
| Floppy 0: Not installed
| Floppy 1: Not installed
+---------------------------+--------------------------------------+-----------+
+------------------------------------------------------------------------------+
| System BIOS Setup - Advanced Configuration
| (C) 2005 General Software, Inc. All rights reserved
+---------------------------------------+--------------------------------------+
| System Management Mode
| Splash Screen
| Primary IDE UDMA
| Firmbase Debug Console
| Usb20
+---------------------------------------+--------------------------------------+
+------------------------------------------------------------------------------+
| System BIOS Setup - Custom Configuration
| (C) 2005 General Software, Inc. All rights reserved
+---------------------------------------+--------------------------------------+
| PCI INT A Assignment
| PCI INT B Assignment
| PCI INT C Assignment
| PCI INT D Assignment
| Write protect BIOS
| Video buffer size
| Flat panel display
| Video refresh rate
| Video data width
| Primary video device
| Memory Timings
| CPU Temp threshold
| CPU overtemp IRQ
| CPU/GLIU speed
| IDE cable type
| Voltage Alert IRQ
| Geode audio controller: Enabled
+---------------------------------------+--------------------------------------+
EBX-11 Reference Manual
VT1528 – EBX-11 CMOS Setup Reference
Basic CMOS Configuration
System Bios Setup - Basic CMOS Configuration
| Date:>Nov 02, 2010 | Typematic Delay
| Time: 00 : 00 : 00 | Typematic Rate
| NumLock: Disabled | Seek at Boot
| BOOT ORDER:
| Boot 1st: Drive C: | F1 Error Wait
| Boot 2nd: (None)
| Boot 3rd: (None)
| Boot 4th: (None)
| Boot 5th: (None)
| Boot 6th: (None)
+--------------------+-----------------+-----------+
| ATA DRV ASSIGNMENT:
| Ide 1: 3 = AUTOCONFIG, LBA
| Ide 2: 3 = AUTOCONFIG, LBA
| Ide 3: 3 = AUTOCONFIG, LBA
Features Configuration
: Enabled | POST Memory Manager
: Disabled | System Management BIOS
: Enabled | Console Redirection
: None | UsbMassStorage
: Enabled |
Custom Configuration
: IRQ 11 | ISA IRQ 3
: IRQ 5 | ISA IRQ 4
: IRQ 9 | ISA IRQ 5
: IRQ 9 | ISA IRQ 10
: Enabled | COM 1 enable/IRQ
: 32 MB | COM 2 enable/IRQ
: Disabled | COM 3 enable/IRQ
: 60 Hz | COM 4 enable/IRQ
: 1 pix/clk | COM 3 mode
: Auto | COM 4 mode
: Optimal | LPT 1 enable/IRQ
: 80*C | LPT 1 mode
: Disabled | BIOS extension
: 500/333 MHz | USB OTG Device
: 40-Wire | Legacy USB support
: Disabled | Periodic SMM IRQ
|
Configuration and Setup
for more information about
: 250 ms
: 30 cps
: None
: Enabled
| Config Box : Enabled
: Enabled
| Parity Checking : (Unused) |
| Memory Test Tick : Enabled
| Debug Breakpoints: (Unused) |
| Debugger Hex Case: Upper
| Memory Test :StdLo FastHi
Sect Hds Cyls | Memory
| Base:
| 631KB
| Ext:
| 219MB
: Disabled |
: Enabled
: Auto
: Enabled
: Disabled
: Disabled
: Disabled
: Disabled
: IRQ4
: IRQ3
: Disabled
: Disabled
: RS232 (4pin) |
: RS232 (4pin) |
: IRQ7
: Printer
: Disabled
: Disabled
: Enabled
: Enabled
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10