Table of Contents
Advertisement
9.3 #SL42-028MV Optional Fan Kit
WARNING - Electrical Grounding Instructions: This appliance is
equipped with a three-prong (grounding) plug for your protection
against shock hazard and should be plugged directly into a properly
grounded three-prong receptacle. Do not cut or remove the grounding
prong from this plug.
WARNING: Installation of this fan kit should be done by a qualified
installer. Verify household breaker is shut off prior to working on any
electrical lines.
IMPORTANT: Installation of an external on/off switch or dimmer switch
is required for operational control of the electrical power supply to the
#600-TLKMV light kit. Consult your qualified electrician for the best
method to accomplish this, especially if installing in combination with
this optional fan kit.
•
This appliance, when installed, must be electrically grounded
in accordance with local codes, or in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70.
•
A pre-installed electrical box is included with the appliance,
along with a speed control assembly in the fireplace
components packet.
•
It easier to install the fan kit before connecting the gas line to the
control board.
This kit includes:
(2) fan assemblies; (1) speed control assembly with cord;
(1) temperature control switch with magnet attached;
(2) philips head screws (black)
1.
Remove the safety barrier and access cover.
2.
With the motor end of the fan's right side facing down and to
the right, insert fan into chamber. Insert the fan at the far end of
the firebox. When the motor end clears the fireplace face, turn
the fan to the left. Rotate the top end down and to the right,
lowering the fan into control compartment.
Position fan as shown in FIGURE 9.5. As you rotate the fan
3.
SPEED CONTROL
ASSEMBLY
60 Hz
INCOMING
WIRING
110-120 V
FIGURE 9.5 Optional Fan Installation and Wiring
HUSSONG MFG. CO., INC.
KOZY HEAT FIREPLACES
towards you, the upper edge of the fan discharge will lock
behind the top edge of fireplace air channel opening, securing
fan into place.
4.
Repeat for the left fan, noting the fan rotation in steps above will
be opposite of the right fan.
5.
Mount the speed control assembly onto the bracket on the gas
valve. Align the slots in the speed control assembly with the
holes in the bracket. See FIGURE 9.5 below. Secure with (2) black
philips head screws (included).
6.
Plug fan cord into the speed control assembly.
7.
Plug the speed control assembly cord into the electrical box
receptacle.
8.
Attach the temperature control switch (magnet attached) to the
firebox floor, centered between the right side of the gas valve
and the right side of the appliance, as shown in FIGURE 9.5.
To adjust the temperature control switch position:
• Before adjusting temperature control switch, unplug 3-prong
plug on fan cord from receptacle.
• Adjust position of temperature control switch to a warmer
location under firebox to turn fan ON sooner or move it to a
cooler location under firebox to turn fan ON later. The fan will
turn on when sensor in temperature control switch reaches
110° F and will turn OFF when sensor reaches 90° F.
• After adjustment, plug 3-prong plug on fan cord into
receptacle.
9.
Turn speed control counter-clockwise until it 'clicks' . This is the
OFF position. Turn speed control ON by turning knob clockwise
past the 'click' - this is the highest setting.
10. Reinstall all components previously removed.
IMPORTANT: This fan will not operate unless speed control has been
turned ON and sufficient heat has been applied to temperature control
switch. The fan will turn ON and OFF automatically as fireplace heats
and cools. Adjust fan to desired speed while it is running.
TEMPERATURE
SWITCH
SECTION 9 ELECTRICAL INFORMATION
#SL42-028MV Optional Fan Kit
57
#CLW-50-MV
R.1 October 2021
Advertisement
Table of Contents
