Table of Contents
Advertisement
7.0 VENTING
7.1 Approved Vent Systems
This appliance is equipped for use with a 5" (127mm) exhaust by 8"
(203mm) air intake co-axial vent pipe system.
This appliance is approved for use with manufacturers (horizontal and
vertical terminations): American Metal Products (Ameri-Vent), BDM,
ICC, Metal Fab*, Olympia Chimney Supply, Inc., Selkirk, and Simpson
DuraVent. See sections 7.1.1 and 7.1.2.
*WHEN INSTALLING METAL FAB VENT SYSTEM with this appliance
adapter part number 5DDA must be used.
15) or section 3.7.2.3 (page 23) for more information.
This appliance can be adapted to use 4" diameter aluminum flexible
pipe by any listed vent manufacturer when used in combination with
an existing minimum 7" ID Class A metal/masonry chimney. Refer to
section 7.5 on page 44 for more information.
This appliance can be adapted to use 3" x 3" flexible co-linear vent
pipes with a 4" x 6-5/8" reducer when used in combination with an
existing minimum 6" x 8" ID masonry or 7" ID Class A metal chimney.
Refer to section 7.6 on page 44 for more information.
The approved vent configurations listed in this manual are shown
with rigid pipe. Listed vent systems (in sections 7.1.1 and 7.1.2) with
flexible pipe can be installed following the vent manufacturer's
installation instructions.
Refer to the vent manufacturer's installation manual for complete
installation instructions. Installation must conform with the
requirements and restrictions specified in this manual.
7.1.1 Approved 5" x 8" Vent Systems
Table 7.1, Approved 5" x 8" Vent Systems
Vent Manufacturer
American Metal Products
(Ameri-Vent)
BDM
Simpson DuraVent
ICC
Metal Fab
(Adapter 5DDA must be used)
Olympia Chimney Supply, Inc.
Selkirk
44
#CLW-50-MV
R.1 October 2021
See section 3.5 (page
Vent Cap Part Number
5DHCS
5DHC
5DVC
5D14S
5D36S
DVR8-HCP
DVR8-HC
DVR8-VCLP
DVR8-VCH
58DVA-HC
58DVA-VCH
58DVA-VC
58DVA-VCE
TM-5HT
TM-5RHT
TM-5SVT - wind/rain shield 4SVTS
must be used
5DHT
5DVT
VDV-VC05
5DT-HC
5DT-HCR
5DT-VT
5DT-VC
5DT-ST14
5DT-ST36
7.1.2 Approved 4" x 6-5/8" Vent Systems
This appliance may be reduced from a 5" x 8" to a 4" x 6-5/8" vent
system using a vent reducer from an approved vent system. Refer
to the vent pipe manufacturer's installation manual for more
information.
Table 7.2, Approved 4" x 6-5/8" Vent Systems
Vent Manufacturer
American Metal Products
(Ameri-Vent)
BDM
Simpson DuraVent
ICC
Metal Fab
Olympia Chimney Supply, Inc.
Selkirk
HUSSONG MFG. CO., INC.
SECTION 7 VENTING
Approved Vent Systems
Vent Cap Part Number
4DHCS
4DHC
4DVC
4D14S
4D36S
DVR6-HCP
DVR6-HC
DVR6-VCLP
DVR6-VCH
46DVA-HC
46DVA-VCH
46DVA-VC
46DVA-VCE
TM-4HT
TM-4RHT
TM-4SVT - wind/rain shield 4SVTS
must be used
4DHT
4DVT
VDV-VC04
4DT-HC
4DT-HCR
4DT-VT
4DT-VC
4DT-ST14
4DT-ST36
KOZY HEAT FIREPLACES
Advertisement
Table of Contents
