Setup Menu List - Sanyo Denki SANUPS E11A Series Instruction Manual

§ 1 2 . 2 S e t u
§ 1 2 . 2 S e t u
User Settings
Guide
No. Menu
Ref. page Item
1 4 3.1
UPS operation mode
Output voltage
2 5 3.2
(RESTART)
Frequency sync
3 6 3.3
range (RESTART)
Battery power
4 7 3.4
startup frequency
(RESTART)
5 8 3.5
PC interface
6 9 3.6
Serial baud rate
UPS operation upon
7 10 3.7
power recovery
8 11 3.8
Buzzer sound
9 12 3.9
Shutdown operation
Overload recovery
10 13 3.10
operation
UPS operation at
11 14 3.11
OFF
(RESTART)
Low battery voltage
12 15 3.12
warning timing
13 16 3.13
Battery backup time
14 17 3.14
Battery type
15 18 3.15
Battery test schedule
Reset battery
16 19 3.16
information
p M e n u L i s t
p M e n u L i s t
Setting
Menu LED Setting
Auto
●○○○
○ Double
○●○○
Conversion
● ○ ○ ○
Economy
●●○○
100V
●○○○
110V
○ ○●○○
115V
○ ● ○ ○
●●○○
120V
○○●○
1%
●○○○
○
3%
○●○○
● ● ○ ○
5%
●●○○
50Hz
●○○○
○
○ ○ ● ○
60Hz
○●○○
- ●○○○
Workstation
○ ○●○○
● ○ ● ○
Serial Login
●●○○
- ○○●○
9600
●○○○
○
4800
○●○○
○ ● ● ○
2400
●●○○
Auto
●○○○
OFF
○●○○
30%
●●○○
○
● ● ● ○
50%
○○●○
80%
●○●○
All patterns
●○○○
Pattern 1
○
○●○○
○ ○ ○ ●
Pattern 2
●●○○
OFF
○○●○
1 second
●○○○
○
3 seconds
○●○○
● ○ ○ ●
Special
●●○○
operation
Auto return
●○○○
○
○ ● ○ ●
Bypass
○●○○
OFF
●○○○
○
● ● ○ ●
Bypass
○●○○
Battery voltage ●○○○
○
2 minutes
○●○○
○ ○ ● ●
3 minutes
●●○○
5 min. 3.5min. ●○○○
20 min. 15 min. ○●○○
30 min. 30 min. ●●○○
40 min. 45 min. ○○●○
○
● ○ ● ●
60 minutes
●○●○
90 minutes
○●●○
120 minutes
●●●○
180 minutes
○○○●
5 years
●○○○
○
10 years
○●○○
○ ● ● ●
3 years
●●○○
180 days
●○○○
90 days
○ ○●○○
30 days
● ● ● ● ●●○○
None
○○●○
Keep Batt. Info. ●○○○
●
○ ○ ○ ○ Reset
○●○○
Default Current
LED Setting Setting
Switch the UPS operating mode automatically.
*
Set the UPS operating mode to Double Conversion mode.
Set the UPS operating mode to Economy mode
Default setting of
See
－
remarks
－
Default setting of
±1%
*
±3%
±5%
Default setting of
See
remarks
Default setting of
Do not use this setting.
Set when using a power management software, LAN card or
*
UPS remote ON and One-touch system shutdown.
Shutdown by serial login.
Do not use this setting.
*
9600 bps.
4800 bps.
2400 bps.
*
Auto restart
The UPS stays off.
Auto restart when battery
charge reaches 30%.
Auto restart when battery
charge reaches 50%.
Auto restart when battery
charge reaches 80%.
* All sounds
Emit sounds on serious failure, battery trouble and key click
sounds.
Emit sounds on serious failure and key click sounds.
Emit key click sounds only.
Turn the UPS off when
*
pressed for 1 second.
Turn the UPS off when
pressed for 3 seconds.
Turn the UPS off on special
operation.
Auto recovery when a
*
certain period of time has
elapsed.
Fixed as bypass power
supply on overload.
* The UPS stays off.
Bypass power supply
When low battery voltage
*
level is detected.
When remaining battery
duration is 2 minutes.
When remaining battery
duration is 3 minutes.
*
Set the UPS backup time on power outage. An external battery
must be connected for settings of 20/15 minutes or higher.
5, 20, 30, 40 min. settings are available for E11A102, 152 and
202 model.
3.5, 15, 30, 45 min. settings are available for E11A302 model.
*
5 years lifetime type
10 years lifetime type
3 years lifetime type
*
Test batteries every 180 days.
Test batteries every 90 days.
Test batteries every 30 days.
No battery check.
*
Keep the battery information as the current condition.
Reset the battery information when you replace the battery.
●: indicates that LED is blinking.
○: indicates that LED is off.
Remarks
E11A*U-J
Set the rated Output voltage.
Same as Input voltage.
E11A*U
Output frequency variation range
(%)
E11A*U-J
Set the output frequency when UPS
starts from the battery power during
AC input power failure.
E11A*U
Set the serial baud rate when a
workstation, PC, or optional LAN
card is connected.
Specify when to restart the UPS
after a power outage and
shutdown of the UPS due to final
discharge of the batteries.
Set the operation for switch to stop
the UPS power supply.
Set the UPS operation after
switching to the bypass power
supply because of overload.
Specify the UPS power supply
conditions when
Set the timing of emitting the low
battery voltage warning alarm
(beep, Red BATT. LOW lit).
Set the battery type. Set this when
you replace the battery or connect an
external battery.
Set the interval (number of days)
for the automatic battery check.
The check is carried out
automatically when the specified
number of days has elapsed.
User setting
is off.
32