Advertisement
B
a
t
t
e
r
y
B
a
t
t
e
r
y
This procedure contains instructions for replaceing the battery pack that is installed in the UPS main unit.
When the battery pack arrives, check the model number shown in the packaging box.
UPS
MODEL No.
E11A102*
BPE11A102A00
E11A152*
BPE11A152A00
E11A202*
BPE11A202A00
E11A302*01*，
BPE11A302A00-1
E11A302*11*
E11A302*02*，
BPE11A302A00-2
E11A302*12*
＜Appearance of battery pack＞
E11A102
Battery pack
Note on battery replacement
•
It is not covered by our warranty if the damage is caused by an agent other than our company during replacement.
When replacing the battery performed by an agent other than our company, shall be responsible for the damage done.
Damage includes damage to equipment and load equipment, data damage and loss profits. However, it is not only limited to these.
•
E11A battery pack is especially designed for our UPS. Do not use a non-specified battery. Also, do not mix old batteries to new one
or use batteries with different manufacturing date. It may cause battery life shortage, leakage and heat generation.
•
Please replace the battery periodically. Batteries that have expired the replacement period may cause a fire.
•
The weight of the battery pack is shown in the table. Please wear insulated gloves, safety shoes when replacing the battery.
Be careful not to injure yourself; dropping it into your feet or pich your hands when handling the battery pack. Bodily injury may occur
if not properly handled. Replacing the battery for E11A302 model should be done by two or more people. Please protect your back to
avoid back pain.
•
The voltage that is listed in the table above is always occuring on the battery terminal, so do not touch them with your hands or
short-circuit them. There is a risk of electrick shock or injury. Also, for safety, use insulation method, such as attaching vinyl tape to
the used battery pack connector.
•
To safely replace the battery pack, please refer to the E11A instruction manual.
R
e
p
l
a
c
e
m
e
n
R
e
p
l
a
c
e
m
e
n
Battery Pack
Mass
Appox. 6 kg
Appox. 9 kg
Appox. 12 kg
Appox. 16 kg
Appox. 20 kg
E11A152
Battery pack
！
CAUTION
t
P
r
o
c
e
d
u
r
t
P
r
o
c
e
d
u
r
The packaging box is used to send back the used battery pack,
do not dispose it. (For Japan)
Voltage
24V
36V
48V
60V
72V
E11A202
E11A302
Battery pack
Battery pack
1
M0012299
e
f
o
r
E
1
1
A
e
f
o
r
E
1
1
A
Scale
Advertisement
Table of Contents
Related Manuals for Sanyo Denki SANUPS E11A102 Series
Summary of Contents for Sanyo Denki SANUPS E11A102 Series
- Page 1 M0012299 This procedure contains instructions for replaceing the battery pack that is installed in the UPS main unit. When the battery pack arrives, check the model number shown in the packaging box. The packaging box is used to send back the used battery pack, do not dispose it.
- Page 2 ① Check the state of usage Not use as UL Standard Use as UL Standard Please ask a service representative Exchange the battery CAUTION If the E11A*U model is used as a UL Standard Product and CE Marking Conformity Product, you may not be able to replace the battery pack by yourself due to a standard restriction.
- Page 3 Continued from page 2 ⇒ Replace the battery pack. 1．Replacing the battery pack. Start E11A Please refer to the instruction manual of E11A for details of the startup procedure. ⇒ Reset the battery information. 2．Resetting the battery information. ⇒ Start the load equipment. 3．[Caution for storage battery replacement ] label Start the load equipment.
- Page 4 ． ． Replace the battery pack with the following steps. ① Remove the UPS front cover. ② Remove the one screw on the right side of the battery cover and remove the battery cover. Not use as UL or CE Standard Use as UL or CE Standard (Authorized person only) ③...
- Page 5 ⑦ Insert the new battery pack into the UPS. ⑧ Plug in the battery connector. ！ CAUTION • ⑦ Insert the battery pack Do not force to insert the battery connector if it is in a different orientation. Damage to the connector may in the direction of the cause electric shock.
- Page 6 Reset the battery information after replacing the battery. If you do this incorrectly, the battery life warning ２ ２ ． ． will not display correctly. Reset the Battery information after replacing the battery installed in the UPS. The following actions will reset all battery information (such as expected battery lifetime, battery operating time, power outage count, etc.): If you have additional batteries, do so after replacing all the battery packs.
- Page 7 ⑤ Press for 3～4 seconds and release it when the buzzer alarms. Press 3 ～ 4 seconds and release it when the buzzer rings “beep, beep”. Please release it as soon as the buzzer alarms ”beep, beep”, it means that the setting is saved in the UPS and resume to normal operation.
- Page 8 ３ ． ” ” ” ” ３ ． Please fill in the ”Cautions for Storage Battery Replacement” label that is attached to the UPS body for the next replacement date (month/year). ① Fill in the blank in the second row for the next replacement date (month/year). Ambient Expected Battery Battery replacement...
Need help?
Do you have a question about the SANUPS E11A102 Series and is the answer not in the manual?
Questions and answers