Alcatel-Lucent 7210 SAS M Interface Configuration Manual
  1. Manuals
  2. Brands
  3. Alcatel-Lucent Manuals
  4. Switch
  5. 7210 SAS E OS
  6. Interface configuration manual

Alcatel-Lucent 7210 SAS M Interface Configuration Manual

Service access switch
Hide thumbs Also See for 7210 SAS M:
Table of Contents

Advertisement

Quick Links

Download this manual
Alcatel-Lucent
Service Access Switch| Release 8.0 Rev.03 Issue 2
7 2 1 0 S A S M , T , X , R 6 , R 1 2 , M x p O S
I n t e r f a c e C o n f i g u r a t i o n G u i d e
3H E 10 38 3A AAB TQ Z Z A
3HE10383AAABTQZZA
Alcatel-Lucent – Proprietary & Confidential
Contains proprietary/trade secret information which is the property of Alcatel-Lucent. Not to be made available
to, or copied or used by anyone who is not an employee of Alcatel-Lucent except when there is a valid nondisclosure
agreement in place which covers such information and contains appropriate non-disclosure and
limited use obligations.
Copyright 2015 © Alcatel-Lucent. All rights reserved.All specifications, procedures, and information in this document are subject to change and revision at any time
without notice. The information contained herein is believed to be accurate as of the date of publication. AlcatelLucent

Advertisement

Table of Contents
loading

Related Manuals for Alcatel-Lucent 7210 SAS M

Summary of Contents for Alcatel-Lucent 7210 SAS M

  • Page 1 Copyright 2015 © Alcatel-Lucent. All rights reserved.All specifications, procedures, and information in this document are subject to change and revision at any time without notice. The information contained herein is believed to be accurate as of the date of publication. AlcatelLucent...
  • Page 2 This document may contain information regarding the use and installation of non-Alcatel-Lucent products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent tries to ensure that this information accurately reflects information provided by the supplier, please refer to the materials provided with any non-Alcatel-Lucent product and contact the supplier for confirmation.

  • Page 3: Table Of Contents

    ABLE OF ONTENTS Alcatel-Lucent 7210 SAS-M, T, X, R6, R12, and Mxp Router Configuration Process ....7 7210 SAS-Series Interfaces Configuration Overview ............. . .10 Chassis Slots and Cards .
  • Page 4 Card, MDA, and Port Command Reference ..........113 Page 2 7210 SAS M, T, X, R6, R12, Mxp Interface Con-...
  • Page 5 Internal port resources on different IMMs.........151 Page 1 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 6 List of Tables Page 2 7210 SAS M, T, X, R6, R12, Mxp Interface Configu-...
  • Page 7 Slot, Card, MDA, and Port Configuration and Implementation Flow .....90 Page 1 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 8 List of Figures Page 2 7210 SAS M, T, X, R6, R12, Mxp Interface Configu-...
  • Page 9 On 7210 SAS devices, not all the CLI commands are supported on all the platforms and in all the modes. In many cases, the CLI commands are mentioned explicitly in this 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration GuidePage 3...
  • Page 10 SAS-Series routers. It is assumed that the network administrators have an understanding of networking principles and configurations, routing processes, and protocols and standards, including: • CLI concepts • MDA, and port configuration • QoS policies • Services Page 4 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration...
  • Page 11 7210 SAS-M, T, X, R6, R12, Mxp OS Routing Protocols Guide This guide provides an overview of routing concepts and provides configuration examples for RIP, OSPF, IS-IS and route policies. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration GuidePage 5...
  • Page 12 If you purchased a service agreement for your 7210 SAS series router and related products from a distributor or authorized re-seller, contact the technical support staff for that distributor or reseller for assistance. If you purchased an Alcatel-Lucent service agreement, contact your welcome center: Web: http://www.alcatel-lucent.com/wps/portal/support...

  • Page 13: Alcatel-Lucent 7210 Sas-M, T, X, R6, R12, And Mxp Router Configuration Process

    Cards on page 11 MDAs MDAs on page 14 Ports Ports on page 20 Reference List of IEEE, IETF, Standards and Proto- and other proprietary col Support on page entities. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 7...
  • Page 14 Getting Started Page 8 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 15: 7210 Sas-Series Interfaces

    MTU Configuration Guidelines on page 87 → Deploying Pre-provisioned Components for 7210 SAS-M, 7210 SAS-X, 7210 SAS-T, and 7210 SAS-Mxp. on page 89 • Configuration Notes on page 189 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 9...

  • Page 16: Configuration Overview

    Ports and interfaces can also be pre-provisioned. When the functionality is needed, the card(s) can be inserted into the appropriate chassis slots when required. Page 10 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 17: Chassis Slots And Cards

    A:7210-SAS-X>show# card =============================================================================== Card Summary =============================================================================== Slot Provisioned Equipped Admin Operational Card-type Card-type State State ------------------------------------------------------------------------------- iom-sas iom-sas sfm-sas sfm-sas up/active =============================================================================== A:7210-SAS-X>show# Sample output for 7210 SAS-T: 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 11...
  • Page 18 If the parameters do not match, the card remains offline. A pre-provisioned slot can remain empty without conflicting with Page 12 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 19 =============================================================================== *A:sasr_dutb>show# Sample output for 7210 SAS-R12: A:A6144909484>show# card =============================================================================== Card Summary =============================================================================== Slot Provisioned Type Admin Operational Comments 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 13...

  • Page 20: Mdas

    If a 2*10G MDA provisioned, it ensures that the BOF parameter "no-service-ports" is configured to specify two ethernet ports. • Only on 7210 SAS-M 24F variant, the no-service-ports BOF parameter is not available for use. Page 14 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 21 MDA port on 7210 SAS-Mxp: The following are the ports in 7210 SAS-Mxp: • 4 x 10G SFP+ • 22 x 1G SFP • 2 x Combo (SFP or Copper) 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 15...

  • Page 22: Digital Diagnostics Monitoring

    Digital Diagnostics Monitoring Digital Diagnostics Monitoring Some Alcatel-Lucent SFP and XFP transponders have Digital Diagnostics Monitoring (DDM) capability. With DDM the transceiver module maintains information about its working status in device registers, such as: • Temperature • Supply voltage •...

  • Page 23: Table 2: Real-Time Ddm Information

    Not supported Supported (embedded in transceiver) AUX2 parameter dependent Not supported Supported (embedded in transceiver) The factory-programmed DDM alarms and warnings that are supported are summarized in Table 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 17...

  • Page 24: Table 3: Ddm Alarms And Warnings

    (embedded in - High Warning transceiver) - Low Warning AUX2 parameter - High Alarm dependent - Low Alarm (embedded in - High Warning transceiver) - Low Warning Page 18 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 25: Alcatel-Lucent Sfps And Xfps

    DDM. Non-DDM and DDM-supported SFPs are distinguished by a specific ICS value. For Alcatel-Lucent SFPs that do not indicate DDM support in the ICS value, DDM data is available although the accuracy of the information has not been validated or verified.

  • Page 26: Ports

    10/100/1000 Base-T Copper SPFs can be used in the any of the SFP ports. It supports all speeds. • For TDM ports, only CES services (CESoPSN and SAToP based) are provided for the T1/ E1 ports. Page 20 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 27: Port Modes

    Hybrid mode can be enabled on a LAG port when the port is part of a single chassis LAG configuration. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 21...

  • Page 28: Configuration Guidelines For Dot1Q-Etype

    0x9100 is classified as null-tagged packet and mapped to a dot1q :0 SAP (if configured) and the priority tag is retained and forwarded. Page 22 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 29 During the non-default dot1q-rvpls and qinq-rvpls, the extra tagged packets is dropped even for an 0x8100 packets on an RVPLS SAP, this is applicable only for network mode (and not access-uplink mode). 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 23...

  • Page 30: Support For Power Over Ethernet (Poe)

    Only DC power is supplied to connected PoE devices (PDs). It works with PoE devices that use injectors where a AC/DC wall device is used to power a remote PoE device. Page 24 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 31 If a port is enabled for PoE is shutdown, then the power supplied to the port is disabled. It restores when the no shutdown command is executed, if the request does not exceed the power budget. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 25...
  • Page 32 Ports Page 26 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 33: Link Layer Discovery Protocol (Lldp)

    Network management information schema and object definitions that suitable for storing connection information about adjacent stations is established. • Provides compatibility with a number of MIBs. For more information, see Figure 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 27...

  • Page 34: Figure 1: Lldp Internal Architecture For A Network Node

    The topology information of the network in Figure 2 can be discovered if, IEEE 802.1ab LLDP is running on each of the Ethernet interfaces in network. Page 28 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 35: Figure 2: Generic Customer Use Case For Lldp

    Interface Configuration MPLS/Native ETH SG/R Core SG/R QinQ DSLAMs Ethernet Links - FE/GE/10GE Figure 2: Generic Customer Use Case For LLDP 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 29...

  • Page 36: Lldp Protocol Features

    LLDP agent. A non-zero value in the TTL field indicates the time duration for which the receiving LLDP agent should retain the sending LLDP agent’s Page 30 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 37: Lldp Tunneling For Epipe Service

    MAC address in the LLDP frames. It is recommended that the customers use these MAC address 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 31...
  • Page 38 This command allows legacy LLDP implementations that do not support these additional destinations MAC addresses to tunnel LLDP frames that use the nearest-bridge destination MAC address. Page 32 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 39: Port Loopback For Ethernet Ports

    This is recommended for use with only VPLS and VLL services. This command affects all the services configured on the port, therefore the user is advised to ensure all the configuration guidelines mentioned for this feature in the command description are followed. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 33...

  • Page 40: Lag

    Packet sequencing must be maintained for any given session. The hashing algorithm deployed by Alcatel-Lucent routers is based on the type of traffic transported to ensure that all traffic in a flow remains in sequence while providing effective load sharing across the links in the LAG.
  • Page 41 LAG starts using the dynamic-cost allowing other nodes to adjust their routing tables according to the revised costs. In this case, when the threshold is not crossed, a fixed metric (all links operational) is advertised. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 35...

  • Page 42: Configuring Lags

    LAG on network ports which provides a standard method to aggregate Ethernet links. The difference lies in how QoS is handled. LAG and QoS Policies on 7210 SAS-M, and 7210 SAS-T Page 36 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 43: Lag And Qos Policies On 7210 Sas-Mxp

    QoS policy is applied to the aggregate traffic that enters the traffic through all the ports of the system. For example, if an ingress policy is configured with a policier of PIR 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 37...

  • Page 44: Lag And Qos Policies On 7210 Sas-R6 And 7210 Sas-R12

    IMM or two different IMMs.. For example, if an network port egress policy is configured with a shaper of PIR 100Mbps, each port would get a PIR of 100 Page 38 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 45: Port Link Damping

    CLI command at the LAG level at the port member level. As a consequence, the transmit laser will be switched off for all LAG members in standby mode. On 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 39...

  • Page 46: Lag Subgroups

    → An eligible member refers to a LAG member link which can potentially become active. This means it is operationally up, and if the slave-to-partner flag is set, the remote system did not disable its use (by signalling stand-by). Page 40 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 47 LAG changes, the selection algorithm is re-run. In case of a tie between two groups (one of them being currently active) the active group remains active (no reverting). 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 41...

  • Page 48: Lag And Ecmp Hashing

    (ECMP) or Link Aggregation (LAG). A 7210 SAS can deploy both at the same time, meaning, using ECMP of two or more Link Aggregation Groups (LAG) and/or single links.The Alcatel-Lucent implementation supports per flow hashing used to achieve uniform loadspreading and per service hashing designed to provide consistent per service forwarding.

  • Page 49: Lag Hashing Fields Used For 7210 Sas-M (Network Mode)

    MPLS traffic (Unlearnt): MPLS label stack (Two labels deep), Ingress Port-Id. Non-IP traffic (Learnt): Source Destination MAC, EtherType, VLAN. Non-IP traffic (Unlearnt): Source Destination MAC, EtherType, VLAN, Ingress Port-Id. Page 44 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 50 PBB traffic: BDA, BSA, ISID, Ingress Port- MPLS traffic: MPLS label stack (Two labels deep), Ingress Port-Id. Non-IP traffic (learnt and unlearnt): Source and Destination MAC, EtherType, VLAN, Ingress Port-Id. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 45...
  • Page 51 (Outer MACs inside the payload, just after the SDP to SAP MPLS header), EtherType All other traffic: Source and Destination MAC (Outer MACs inside the payload, just after the MPLS header) Page 46 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 52 IP traffic (unlearnt): Source and Destination IP, Source and Destination L4 ports, Ingress Port-Id. L2/non-IP traffic (learnt): BDA, BSA L2/non-IP traffic (unlearnt): BDA, BSA, ISID, Ingress Port-Id 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 47...
  • Page 53 L2/non-IP traffic: CSA, CDA, EtherType, SAP) VLAN, Ingress Port-Id PBB Epipe service: IP traffic: CSA, CDA Terminating PBB BEB traffic L2/non-IP traffic: CSA, CDA, EtherType (PBB Epipe SAP to B-SAP) Page 48 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 54 Port-Id. interface Network port IPv4 interface: IPv4 unicast traffic: Source and Destination IP, Source and Destination L4 ports, Ingress IPv4 network interface to IPv4 Port-Id. network interface 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 49...
  • Page 55 2. In the LSR case, incoming labels are used for hashing. 3. ‘Learnt’ wherever mentioned corresponds to Destination MAC. 4. Source/Destination MAC refer to ‘Customer Source/Destination MACs’ unless otherwise specified Page 50 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 56: Lag Hashing Fields Used For 7210 Sas-X

    Destination IP, Source and Destination L4 ports, PBB BCB Traffic (that is, B-SAP Ingress Port-Id. to B-SAP) L2/non-IP traffic (learnt and unlearnt): BDA, BSA, ISID, Ingress Port-Id. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 51...
  • Page 57 Source and Destination L4 ports, Ingress Port-Id, VLAN. IES SAP to IES SAP IPv4 network port interface to IPv4 network port interface IES SAP to IPv4 network port interface Page 52 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 58 2. In the LSR case, incoming labels are used for hashing. 3. ‘Learnt’ wherever mentioned corresponds to Destination MAC. 4. Source/Destination MAC always refer to ‘Customer Source/Destination MACs’ unless otherwise specified. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 53...

  • Page 59: Lag Hashing Fields Used For 7210 Sas-M (Access-Uplink Mode)

    IPv4 unicast traffic: Source and Destination IP, Source and Destination L4 ports. IES SAP to IES SAP NOTE: 1. The term ‘Learnt’ mentioned corresponds to Destination MAC. Page 54 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 60: Lag Hashing Fields Used For 7210 Sas-T Access-Uplink Mode

    MPLS traffic (Unlearnt-L2): MPLS label stack (Two labels deep), Ingress Port-Id Non-IP traffic (Learnt): Source and Destination MAC, EtherType, VLAN Non-IP traffic (Unlearnt): Source and Destination MAC, EtherType, Ingress Port-Id, VLAN 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 55...
  • Page 61 3. VLAN ID is considered for Learnt - PBB, MPLS, Non-IP traffic in VPLS service only for traffic ingressing at dot1q, Q.*, Q1.Q2 SAPs. 4. Only outer VLAN tag is used for hashing. Page 56 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 62: Lag Hashing Fields Used For 7210 Sas-T Network Mode

    PBB traffic: BDA, BSA, VLAN MPLS traffic : Source and Destination MAC (Outer MACs of the Ethernet packet that encapsulates MPLS packet), VLAN Non-IP traffic: Source and Destination MAC, EtherType, VLAN 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 57...
  • Page 63 PBB traffic: BDA, BSA, ISID, Ingress Port- MPLS traffic: Source and Destination IP, MPLS label stack (Two labels deep), Ingress Port-Id. Non-IP traffic: Source and Destination MAC, EtherType, VLAN, Ingress Port-Id. Page 58 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 64 Source and Destination IP (only when IP header immediately follows MPLS header without any Source and Destination MAC in between inside the MPLS encapsulation), Ingress Port-Id. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 59...
  • Page 65 IP traffic: Source and Destination IP, Source and Destination L4 ports, Ingress Port-Id Originating PBB BEB traffic (that is, PBB Epipe I-SAP to B-SAP) L2/non-IP traffic: CSA, CDA, EtherType, VLAN, Ingress Port-Id Page 60 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 66 IP interface (Network or SAP) to IP interface (Network) 1. VPLS service, SDP to SDP: Test has been performed only for VC label variation with the same Tunnel label. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 61...

  • Page 67: Lag Hashing Fields Used For 7210 Sas-R6 And 7210 Sas-R12

    MPLS traffic: Source and Destination IP, MPLS label stack (Two labels deep), Ingress Port-Id. Non-IP traffic (learnt and unlearnt): Source and Destination MAC, EtherType, VLAN, Ingress Port-Id. Page 62 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 68 SDP to SAP payload, just after the MPLS header), EtherType All other traffic (learnt): Source and Destination MAC (Outer MACs inside the payload, just after the MPLS header) 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 63...
  • Page 69 Destination port (L4), Ingress portId SAP to Network Port Interface Network Port Interface (IP traffic) Source, Destination IP address, Source, Destination port (L4), Ingress portId Network Interface to Network Interface Page 64 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 70 With more than 2 ports in the lag, load- balancing is expected to take place. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 65...

  • Page 71: Lag Hashing Fields Used For 7210 Sas-Mxp

    MPLS header), Ingress Port- SDP to SDP MPLS – LSR All traffic: MPLS label stack (Two labels deep), Ingress Port-Id. Page 66 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 72 Network port IPv6 interface: IPv6 unicast traffic: Source and Destination IP, Source and Destination L4 ports, Ingress Port-Id. IPv6 network interface to IPv6 network interface 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 67...

  • Page 73: Ecmp Hashing Fields Used For 7210 Sas Devices In Network Mode

    8. 'sap_index' is a value assigned uniquely for each SAP internally. ECMP Hashing fields used for 7210 SAS devices in Network mode Table 13: ECMP Hashing mechanism for services configured on 7210 SAS devices in Page 68 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 74 IPv4 traffic SAP or SAP or • Source and Network Port Network Port Destination IP IP interface IP interface • Source and Destination L4 ports • Ingress Port-Id 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 69...

  • Page 75: Multi-Chassis Lag

    LACP is used to manage the available LAG links into active and standby states such that only links from 1 aggregation node are active at a time to/from the access node. Characteristics related to MC are: Page 70 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 76 → Traffic over the signalling link is encrypted using a user configurable message digest key. • MC-LAG function provides active/stand-by status to other software applications in order to built a reliable solutions. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 71...

  • Page 77: Figure 4: Mc-Lag L2 Dual Homing To Remote Pe Pairs

    Dual-homing to local PE pair → both end-points attached with MC-LAG → one end-point attached with MC-LAG → both end-points attached with MC-LAG to two overlapping pairs Page 72 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 78: Figure 5: Mc-Lag L2 Dual Homing To Local Pe-Pairs

    In case there are no such objects available at the local node, the packets will be cross-connected to inter-chassis pseudowire. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 73...

  • Page 79: Point-To-Point (P2P) Redundant Connection Across Layer 2/3 Vpn Network

    LAG. The status of LAG links is reflected in status signaling of pseudo-wires set between all participating PEs. The combination of active and stand-by states across LAG links as well and pseudo-wires give only 1 unique path between pair of MSANs. Page 74 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 80 Both ends of the same VLL connections are local to the same redundant-pair. • One end VLL endpoint is on a redundant-pair the other on single (local or remote) node. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 75...

  • Page 81: Dslam Dual Homing In Layer 2 Network

    • 7210 SAS-M and 7210 SAS-T access-uplink mode supports active/standby LAG, which allows it to be used as client in an MC-LAG solution. Page 76 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 82: Configuring Multi-Chassis Redundancy

    The following displays the configuration: *7210-SAS>config>redundancy# info ---------------------------------------------- multi-chassis peer 1.1.1.1 create shutdown sync shutdown port 1/1/1 create exit 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 77...
  • Page 83 10.20.1.3 create mc-lag lag 3 lacp-key 1 system-id 00:00:00:aa:bb:cc remote-lag 1 system-pri- ority 1 no shutdown exit no shutdown exit exit ---------------------------------------------- *7210-SAS>config>redundancy# Page 78 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 84: G.8032 Protected Ethernet Rings

    Services Guide. 802.1x Network Access Control The Alcatel-Lucent 7210 SAS supports network access control of client devices (PCs, STBs, etc.) on an Ethernet network using the IEEE. 802.1x standard. 802.1x is known as Extensible Authentication Protocol (EAP) over a LAN network or EAPOL.

  • Page 85: Figure 8: 802.1X Architecture

    On the back end, the communication between the authenticator and the authentication server is done with the RADIUS protocol. The authenticator is thus a RADIUS client, and the authentication server a RADIUS server. Page 80 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 86: Figure 9: 802.1X Authentication Scenario

    The RADIUS server checks the supplied credentials, and if approved will return an Access Accept message to the router. The router notifies the client with an EAP-Success PDU and puts the port in authorized state. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 81...
  • Page 87 If the timer expires, the access request message is sent again, up to max-auth-req times. The default value is 60. The range is 1 — 3600 seconds. Page 82 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 88: Figure 10: 802.1X Eapol Timers (Left) And Radius Timers (Right)

    The range of reauth-period is 1 — 9000 seconds (the default is 3600 seconds, one hour). Note that the port stays in an authorized state during the re-authentication procedure. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 83...
  • Page 89 802.1x configuration (shutdown or no shutdown). Note that enabling 802.1x tunneling requires the 802.1x mode to be set to force-auth. Enforcement is performed on the CLI level. Page 84 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 90: 802.3Ah Oam

    → All 7210 SAS platforms, process the received EFM OAM dying gasp, on a port enabled for EFM and generate a SNMP trap. • EFM OAMPDU tunneling. • High resolution timer for EFM OAM in 500ms interval (minimum). 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 85...

  • Page 91: Oam Events

    The 7210 does not generate EFM OAM PDUs with these flags except for the dying gasp flag. However, it supports processing of these flags in EFM OAM PDUs received from the peer. Page 86 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 92: Remote Loopback

    The physical (access and network) port, service, and SDP MTU values must be individually defined. • MTU values must conform to both of the following conditions: 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 87...

  • Page 93: Table 14: Mtu Default Values

    The packet is dropped as packet length is greater than the service MTU configured. Note: Please check the 7210 platform release notes for other restrictions with regards to MTU checking and processing on each of the platforms. Page 88 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 94: Deploying Pre-Provisioned Components For 7210 Sas-R6 And 7210 Sas-R12

    NOTE: The CLI command allow-imm-family is not supported on 7210 SAS-R12, as there is no need to pre-provision the chassis. It only accepts IMMv2 card (imm-sas-r-b). 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 89...

  • Page 95: Configuration Process Overview

    It is typically used only on platforms that are chassis based and support slots for inserting cards, like the 7210 SAS-R6 and 7210 SAS-R12. Page 90 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 96 SAS-M. It is not required on platforms that do not support an MDA, like 7210 SAS-X, 7210 SAS-T, 7210 SAS-R6 and 7210 SAS-R12. 7210 SAS-Mxp does not have a expansion slot (and hence does not support MDA. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 91...
  • Page 97 Configuration Process Overview Page 92 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 98: Configuring Physical Ports With Cli

    Service Management Tasks on page 110 → Modifying a Card Type on page 111 → Deleting a Card on page 112 → Deleting Port Parameters on page 112 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 93...

  • Page 99: Preprovisioning Guidelines

    (for example, 7210 SAS-M). Typically on 7210 platforms that do not support any removable cards and/or MDAs, the MDAs are pre-provisioned for all fixed ports. Page 94 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 100: Pre-Provisioning A Port

    LAG combine to form one logical connection. A LAG also provides redundancy in case one or more links that participate in the LAG fail. For command syntax, see Configuring LAG Parameters on page 108. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 95...

  • Page 101: Basic Configuration

    Specify line card type (must be an allowed card type). • Identify MDA slot (if applicable) • Specify MDA (must be an allowed MDA type) - if applicable • Identify specific port to configure. Page 96 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 102: Configuring Cards And Mdas

    The following example displays some MDA configurations for 7210 SAS-M: A:ALA-B>config>card# info ---------------------------------------------- card-type iom-20g mda 1 mda-type m10-1gb-sfp exit mda 2 mda-type m10-1gb-sfp exit ---------------------- A:ALA-B>config>card# 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 97...

  • Page 103: Configuration Notes For Provisioning Of Cards

    The user can change the value of allow-imm-family at any time. It does not change the operational state of the chassis. For the value to take effect, user must reboot. If software detects a mismatch in Page 98 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 104 Default imm-sas-10sfp imm-sas-r Default imm-sas-2xfp imm-sas-r Default =============================================================================== *A:sasr_dutb>show>system# NOTE: For more information about upgrading the chassis to use IMMv2 cards, see the “7210 SAS Installation Guide”. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 99...
  • Page 105 Configuration Notes for provisioning of cards Page 100 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 106: Common Configuration Tasks

    • Configuring LAG Parameters on page 108 • Modifying a Card Type on page 111Deleting a Card on page 112 • Deleting Port Parameters on page 112 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 101...

  • Page 107: Configuring Ports

    Configuring Ports Configuring Ports • Configuring Ethernet Port Parameters on page 103 Page 102 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 108: Configuring Ethernet Port Parameters

    Once a port has been configured for access mode, multiple services may be configured on the port. The following example displays an Ethernet access port configuration : *A:7210-SAS>config>port# info ---------------------------------------------- ethernet 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 103...
  • Page 109 Configuring Ports mode access access egress exit exit encap-type dot1q mtu 9212 exit no shutdown ---------------------------------------------- *A:7210-SAS> Page 104 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 110: Configuring 802.1X Authentication Port Parameters

    The following example displays an 802.1x port configuration: A:ALA-A>config>port>ethernet>dot1x# info detail ---------------------------------------------- port-control auto radius-plcy dot1xpolicy re-authentication re-auth-period 3600 max-auth-req 2 transmit-period 30 quiet-period 60 supplicant-timeout 30 server-timeout 30 ---------------------------------------------- 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 105...

  • Page 111: Configuring Channelized Ports

    ALA-A>config>port>tdm>e1# channel-group 2 ALA-A>config>port>tdm>e1>channel-group# timeslots 3 ALA-A>config>port>tdm>e1>channel-group# no shutdown ALA-A>config>port>tdm>e1>channel-group# exit ALA-A>config>port>tdm>e1# channel-group 3 ALA-A>config>port>tdm>e1>channel-group# timeslots 11,12 ALA-A>config>port>tdm>e1>channel-group# no shutdown ALA-A>config>port>tdm>e1>channel-group# exit ALA-A>config>port>tdm>e1# no shutdown ALA-A>config>port>tdm>e1# exit Page 106 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...
  • Page 112 ALA-A>config>port>tdm>e1# no shutdown ALA-A>config>port>tdm>e1# channel-group 1 ALA-A>config>port>tdm>e1>channel-group# no shutdown ALA-A>config>port>tdm>e1>channel-group# exit ALA-A>config>port>tdm>e1# no shutdown ALA-A>config>port>tdm# info ----------------------------------------------------------------------------------------- ALA-A>config>port>tdm# Services can now be applied to the configured channelized ports. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 107...

  • Page 113: Configuring Lag Parameters

    6/1/1 priority 32768 sub-group 1 no dynamic-cost lacp active administrative-key 32770 port-threshold 0 action down lacp-xmit-interval fast lacp-xmit-stdby no selection-criteria no hold-time standby-signaling lacp no shutdown ---------------------------------------------- *A:7210SAS>config>lag# Page 108 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 114: Crc Error Monitoring

    SNMP trap should be raised, and the port should be brought operationally down. When the condition is cleared, a SNMP trap message to clear the event is sent out. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 109...

  • Page 115: Service Management Tasks

    CLI syntax to modify an MDA: CLI Syntax: config> port port-id shutdown CLI Syntax: config> card slot-number shutdown [no] mda mda-number [no] mda-type mda-type shutdown Page 110 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 116: Modifying A Card Type

    The modify operation cannot be performed on an IOM card that is auto equipped and auto provisioned during bootup and is fixed. CLI Syntax: config> port port-id [no] shutdown CLI Syntax: config> card slot-number mda mda-number [no] mda-type mda-type [no] shutdown 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 111...

  • Page 117: Deleting A Card

    Deleting Port Parameters Use the following CLI syntax to delete a port provisioned for a specific card: CLI Syntax: config>port port-id shutdown no port port-id Page 112 7210 SAS M, T, X, R6, R12, Mxp Interface Configu- ration Guide...

  • Page 118: Card, Mda, And Port Command Reference

    LAG Commands on page 125 • Ethernet Commands on page 119 • Show Commands on page 128 • Clear Commands on page 129 • Debug Commands on page 129 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 113...
  • Page 119 MDA Commands config — [no] card slot-number — — [no] mda-slot — mda-type mda-type — no mda-type — [no] shutdown — [no] sync-e — [no] shutdown Page 114 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 120 Command Reference Port Configuration Commands config — port — no port — description long-description-string — no description — ethernet — [no] shutdown 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 115...
  • Page 121 M (both access-uplink and network mode) and 7210 SAS-T. config — port —Port Configuration Commands — no port — split-horizon-group group-name — no split-horizon-group config —LAG Commands — [no] [lag-id] — [no] split-horizon-group group-name Page 116 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 122 R6, 7210 SAS-R12, 7210 SAS-T, 7210 SAS X, 7210 SAS-Mxp and 7210 SAS-M network mode. config — port {port-id} — no port — description long-description-string — no description — dwdm — channel channel — ethernet — shutdown 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 117...
  • Page 123 Card, MDA, and Port Command Reference Port Loopback Commands for 7210 SAS devices configure — system — loopback-no-svc-port {mirror | mac-swap| testhead} port-id — no loopback-no-svc-port Page 118 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 124 — policy-id — no — queue-policy name — no queue-policy Port Ethernet Commands config — [no] port {port-id} — ethernet — autonegotiate [limited] — [no] autonegotiate 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 119...
  • Page 125 — sd-threshold threshold [multiplier multiplier] — sf-threshold threshold [multiplier multiplier] — window-size seconds Port Ethernet 802.1x Commands config — [no] port {port-id} — ethernet — dot1x Page 120 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 126 — [no] shutdown — [no] transmit-interval interval [multiplier multiplier] — [no] tunneling Port Ethernet LLDP Commands config — [no] port {port-id} — ethernet — lldp — [no] tunnel-nearest-bridge-dest-mac 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 121...
  • Page 127 Port Ethernet Sync Commands config — [no] port {port-id} — ethernet — no port-clock — port-clock {master|slave|automatic} — — [no] shutdown — [no] code-type sonet | sdh — [no] tx-dus Page 122 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 128 {no-crc-g704 | g704 | e1-unframed} — loopback {line | internal} — no loopback — [no] report-alarm [ais] [los] [oof] [rai] [looped] — [no] shutdown — no signal-mode {cas} 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 123...
  • Page 129 Card, MDA, and Port Command Reference — [0dB | -7.5dB | -15.0dB | -22.5dB] — length {133 | 266 | 399 | 533 | 655} — line-impedance {Impedance in ohms} Page 124 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 130 [create] — authentication-key [authentication-key | hash-key] [hash | hash2] — no authentication-key — description description-string — no description — [no] mc-lag — hold-on-neighbor-failure multiplier — no hold-on-neighbor-failure 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 125...
  • Page 131 — port [port-id | lag-id] [sync-tag sync-tag] [create] — no port [port-id | lag-id] — range encap-range [sync-tag sync-tag] — no range encap-range — [no] shutdown Page 126 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 132 — [no] test-pattern {all-zeros | all-ones} [crc-enable] — bit-error-threshold bit-errors — low-priority-defect {allDef|macRemErrXcon|remErrX- con|errXcon|xcon|noXcon} — mac-address mac-address — one-way-delay-threshold seconds — [no] shutdown — [no] shutdown 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 127...
  • Page 133 [peer ip-address [lag lag-id]] statistics — sync peer [ ip-address ] — sync peer [ ip-address ] detail — sync peer [ ip-address ] statistics — system — internal-loopback-ports [detail] Page 128 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 134 Debug Commands debug — [lag-id lag-id port port-id] [all] — [lag-id lag-id port port-id] [sm] [pkt] [cfg] [red] [iom-upd] [port-state] [timers] [sel-logic] [mc] [mc-pkt] — no [lag-id lag-id] 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 129...
  • Page 135 Card, MDA, and Port Command Reference Page 130 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 136 TDM Commands (Applicable to 7210 SAS-M when using the CES MDA) on page 182 • LAG Commands on page 191 • Ethernet Ring Commands on page 198 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 131...
  • Page 137 — The default state for a card is no shutdown. mda — The default state for a mda is no shutdown. lag — The default state for a Link Aggregation Group (LAG) is shutdown. Page 132 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 138 The IOM card is equipped and preprovisioned for slot 1. Parameters card-type — The type of card to be configured and installed in that slot. Values 7210 SAS-M and 7210 SAS-Mxp - iom-sas 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 133...
  • Page 139 By default, the system attaches the default system resource-profile to each IMM when it is booted up. Parameters policy-id — Specifies the system resource profile policy to use for this card. Values [1-16] Page 134 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 140 • 7210 SAS-X does not support any expansion slot. It does not support use of this command. • 7210 SAS-M, X, T, Mxp, R6, and R12 are auto-provisioned. Except for the CES MDA and the 2x10G MDA on 7210 SAS-M devices. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 135...
  • Page 141 Refer to the 7210 SAS Basic System Configuration Guide for more information on Synchronous Ethernet. Default no sync-e Page 136 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 142 This command enables the context to configure egress buffer pool parameters which define the percentage of the pool buffers that are used for CBS calculations and specify the slope policy that is configured in the config>qos>slope-policy context. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 137...
  • Page 143 This command specifies an existing slope policy which defines high and low priority RED slope parameters and the time average factor. The policy is defined in the config>qos>slope-policy context. Page 138 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 144 Note: This command is supported only on 7210 SAS-X. It is not supported on 7210 SAS-M, SAS-T, 7210 SAS-Mxp, 7210 SAS-R6 and 7210 SAS-R12 devices. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 139...

  • Page 145: Table 15: Default Values For Sap-Qos-Marking In Access And Hybrid Port Modes

    Sap-qos-marking is disabled Hybrid Network No effect on CLI and thus the command is disabled. Access Sap-qos-marking is enabled The behavior on access ports are as follows: Page 140 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 146 • fc-based • sap-based In the "fc-based" mode the priority of all egress queues across all SAPs are considered to determine the next queue to be scheduled. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 141...
  • Page 147 To use the SAP egress aggregate-rate-limit command the port scheduler mode must be set to 'sap-based' using this command. For more information on the aggregate-rate-limit command, see 7210 SAS-X Services guide. Default fc-based Page 142 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 148 The port must be a physical port to set the dwdm channel Parameters channel — Specifies the channel. Values 0, 17-61, 175-605] where: 17-61 is used for 100GHz channels 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 143...
  • Page 149 WRED slope to use at ingress (access SAPs), in addition to egress (access SAPs and network/ hybrid port). NOTE: For more infomation, see the “7210 SAS QoS Configuration User Guide”. Default no enable-dei Parameters none Page 144 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 150 Access: An access port is used for customer facing traffic on which services are configured. A Service Access Point (SAP) can only be configured on an access port. When a port is configured for access mode, 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 145...
  • Page 151 — Configures the Ethernet port for transport (ethernet uplinks available only in access-uplink mode). hybrid — Configures the Ethernet port for hybrid use (available only in network mode). Page 146 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 152 — Specifies the 48-bit MAC address in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 147...
  • Page 153 This command allows user an option to turn on either IP multicast or IGMP snooping on a given port. These are mutually exclusive. Page 148 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 154 L3/IP multicast lookups. Default multicast-ingress l2-mc. Parameters l2-mc — Enables IGMP snooping on the port with L2 multicast lookup. ip-mc — Enables IP multicast (Layer-3) lookups on the port. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 149...
  • Page 155 • On 7210 SAS-R6 and 7210 SAS-R12, user has a fixed number of internal ports for use with OAM tools (such as testhead OAM tool, mac-swap OAM tool and Dot1q/remote mirroring OAM tool) that need the Page 150 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...

  • Page 156: Table 17: Internal Port Resources On Different Imms

    — Specifies the physical port ID in the slot/mda/port format. mac-swap — Specifies the port specified by the port-id is dedicated for use by the port loopback with mac- swap application/OAM tool. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 151...
  • Page 157 — Specifies the port specified by the port-id is dedicated for use by the mirroring application/OAM tool. testhead — Specifies the port specified by the port-id dedicated for use by the Testhead application or the OAM tool. Page 152 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 158 Interface Configuration 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 153...
  • Page 159 Note: For tdm>ds1 and tdm>e1 only access mode is supported. Network and hybrid is not supported. Default network — for Ethernet ports Parameters access — Configures the Ethernet port as service access. network — Configures the Ethernet port for transport network use. Page 154 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 160 If the autonegotiate limited keyword option is specified the port will autonegotate but will only advertise a specific speed and duplex. The speed and duplex advertised are the speed and duplex settings configured 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 155...
  • Page 161 — Specifies the type of ethernet combo port. Values sfp | copper | auto crc-monitor Syntax crc-monitor Context config>port>ethernet Description This command configures Ethernet CRC Monitoring parameters. Default none Page 156 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 162 — Represents the rate of CRC errored Ethernet frames. Values multiplier — Represents the multiplier used to scale the CRC error ratio. Values window-size Syntax [no] window-size seconds Context config>port>ethernet>crc-monitor 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 157...
  • Page 163 (that is, traffic mapped to SAPs and network IP interfaces). It is not supported for network ports. • Dot1q-preserve SAPs cannot be configured on dot1q encap ports configured to use ethertype other than 0x8100. Page 158 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 164 — Sets the link to full duplex mode. half — Sets the link to half duplex mode. efm-oam Syntax efm-oam Context config>port>ethernet Description This command configures EFM-OAM attributes. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 159...
  • Page 165 — Specifies the transmit interval. Values 1 — 600 (in 100 milliseconds) multiplier multiplier — Specifies the multiplier for transmit-interval to set local link down timer. Values 2 — 5 Page 160 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 166 — Ingress frames will not use any tags to delineate a service. As a result, only one service can be configured on a port with a null encapsulation type. qinq — This encapsulation type is specified for QinQ access SAPs. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 161...
  • Page 167 MTU value is set to default. The MTU check is enforced on self-generated and forwarded packets. The system uses the configured IP MTU value to ensure that packets sent out of the IP interfaces Page 162 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 168 If not, power is not supplied to the port. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 163...
  • Page 169 • This command takes effect only for access ports and hybrid ports. On hybrid ports, it applies to all traf- fic (that is, traffic mapped to SAPs and network IP interfaces). It is not supported for network ports. Page 164 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 170 The master-slave relationship between the two ports of the nodes is determined during auto-negotiation of the link parameters and is automated; there is no 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 165...
  • Page 171 10 — Sets the link to 10 mbps speed. 100 — Sets the link to 100 mbps speed. 1000 — Sets the link to 1000 mbps speed. Page 166 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 172 IGMP groups. • For loop back to be functional, the following are not required: - SFP or XFPs need not be inserted into the device. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 167...
  • Page 173 SAP. Hence, port loopback with mac-swap cannot be used for learning or aging. Page 168 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 174 5. Enable loop back and execute the command config >port>ethernet> loopback internal. 6. Enable the port and execute the command config>port> no shutdown. 7. Perform the required tests. 8. Disable the port and execute the command config>port> shutdown. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 169...
  • Page 175 SONET set of values. Configuring the code-type is only applicable to Synchronous Ethernet ports. It is not configurable on TDM ports. For the code-type, SDH refers to ITU-T G.781 Option-1,while SONET refers to G.781 Option 2 (equivalent to Telcordia GR-253-CORE). Default Page 170 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 176 Synchronous Ethernet port to be set to QL-DUS/QL-DNU. This capability is provided to block the use of the interface from the SR/ESS for timing purposes. Default no tx-dus 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 171...
  • Page 177 The no form of this command returns the value to the default. Default Parameters max-auth-request — The maximum number of RADIUS retries. Values 1 — 10 port-control Syntax port-control [auto | force-auth | force-unauth] Context config>port>ethernet>dot1x Page 172 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 178 (under config>security>dot1x) before it can be associated to a port. If the RADIUS policy-id does not exist, an error is returned. Only one 802.1x RADIUS policy can be associated with a port at a time. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 173...
  • Page 179 When this timer expires, the 7210 SAS will re-send the access request message, up to the specified number times. The no form of this command returns the value to the default. Page 174 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 180 Default Parameters seconds — The server transmit period in seconds. Values 1 — 3600 down-when-looped Syntax down-when-looped Context config>port>ethernet Description This command configures Ethernet loop detection attributes. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 175...
  • Page 181 This command configures the minimum wait time before re-enabling port after loop detection. Default no retry-timeout Parameters timer — Specifies the minimum wait time before re-enabling port after loop detection. Values 0, 10 — 160 Page 176 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 182 This command allows legacy LLDP implementations that do not support these additional destinations MAC addresses to tunnel LLDP frames that use the nearest-bridge destination MAC address. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 177...
  • Page 183 Syntax [no] notification Context config>port>ethernet>lldp>dstmac Description This command enables LLDP notifications. The no form of the command disables LLDP notifications. Page 178 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 184 — Indicates that the LLDP agent should transmit system name TLVs. sys-desc — Indicates that the LLDP agent should transmit system description TLVs. sys-cap — Indicates that the LLDP agent should transmit system capabilities TLVs. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 179...
  • Page 185 (access) or network information. A network accounting policy can only be associated with the network port configurations. Accounting policies are configured in the config>log>accounting-policy context. Values 1 — 99 Page 180 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 186 PIR rates, as well as forwarding-class to queue mappings. The network-queue policy is defined in the config>qos>network-queue context. Default default Parameters name — Specifies an exisiting network-queue policy name. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 181...
  • Page 187 The no form of this command disables DS-1 capabilities. Default None Parameters ds1-id — Identifies the DS-1 channel being created. Values DS1: 1 — 28 Syntax Context config>port>tdm Page 182 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 188 For 'short' buildout the following values are valid: Values lboNotApplicable — Not applicable Default 'NotApplicable'. length Syntax length {133 | 266 | 399 | 533 | 655} Context config>port>tdm 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 183...
  • Page 189 This command specifies the clock source to be used for the link transmit timing. Adaptive timing is supported only on T1/E1 CES MDA card ports used for TDM pseudowires. Page 184 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 190 — Configures the DS-1 port for super frame framing. ds1-unframed — Specifies the DS1 unframed (G.703) mode for DS1 interfaces. DS1 unframed mode is only applicable if the encapsulation type is set to cem. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 185...
  • Page 191 This command defines the data pattern to be transmitted when the circuit emulation service is not operational or temporarily experiences under-run conditions.This command is only valid for cesopsn services. Page 186 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 192 The Tx signal is looped back and received by the interface. Note: The loopback command is not saved to the system configuration. The no form of this command disables the specified type of loopback. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 187...
  • Page 193 This command configures the DS1 channel response to remote loop backs. When enabled, the channel responds to remote loop backs; when disabled, the channel does not respond. Default no remote-loop-respond Page 188 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 194 E1 links with a mix of voice and data channels cannot be transported directly across a 7210 SAS network. For a workaround, please contact Alcatel-Lucent technical service representatives. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 189...
  • Page 195 Each member of the list can either be a single timeslot or a range of timeslots. Values 1 — 24 for DS-1 interfaces 2 — 32 for E-1 interfaces Page 190 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 196 Default No LAGs are defined. Parameters lag-id — The LAG identifier, expressed as a decimal integer. Values SAS-M,X,T, Mxp- [1..25] SAS-R6, R12-[1..63] 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 191...
  • Page 197 If the encapsulation type of the LAG port is changed, the encapsulation type on all the port members will also change. The encapsulation type can be changed on the LAG port only if there is no interface associated Page 192 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 198 Group to which the link belongs, move the link to that Link Aggregation Group, and enable its transmission and reception functions in an orderly manner. LACP can be enabled on a maximum of 12 ports. Default no lacp 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 193...
  • Page 199 This forces a timeout of the standby links by the peer. Use the no form if the peer does not implement the correct behavior regarding the lacp sync bit. Default lacp-xmit-stdby Page 194 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 200 Note: The 7210 SAS-M and 7210 SAS-T access-uplink mode supports only 'down' value for the action parameter. Network mode (7210 SAS-M, 7210 SAS-T, 7210 SAS-X, 7210 SAS-R6, 7210 SAS-R12 and 7210 SAS-Mxp) supports both 'dynamic-cost' and 'down' values for action parameter. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 195...
  • Page 201 This means it is operationally up (not disabled) for use by the remote side. The slave-to-partner parameter can be used to control whether or not this latter condition is taken into account. Page 196 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 202 — The laser of the standby links in the LAG are shutoff to indicate "standby" status. It allows user to use LAG standby link feature without LACP, if the peer node does not support LACP. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 197...
  • Page 203 This command configures the guard time for an Eth-Ring. The guard timer is standard and is configurable from “x”ms to 2 seconds The no form of this command restores the default guard-time. Default 5 deciseconds Parameters value — Specifies the guard-time. Page 198 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 204 Default 0 - the fault will be reported immediately to the protection module. Parameters value — Specifies the down timeout. Values 0 — 5000 deciseconds 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 199...
  • Page 205 MAC for the ring control. This command allows the chassis MAC to be overridden with another MAC address. The no form of this command removes the RPL link. Default no node-id Parameters mac — <xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx> Page 200 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 206 This command links the G.8032 sub-ring to a ring instance or to a VPLS instance. The ring instance must be a complete ring with two paths but may itself be a sub-ring or a major ring (declared by its configuration on 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 201...
  • Page 207 The no form of this command removes the path a or b. Default no path Parameters raps-tag <qtag [.qtag]> — Specifies the VIDqtag. Values Dot1q: 1—4094 Page 202 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 208 This command enables the context to configure ETH-CFM parameters. Syntax [no] mep mep-id domain md-index association ma-index Context config>eth-ring>path>eth-cfm Description This command provisions an 802.1ag maintenance endpoint (MEP). 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 203...
  • Page 209 Link Layer OAM does not provide the required detection time. The no form of this command disables the use of the CC state by the Ethernet ring. Page 204 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 210 This command enables eth-test functionality on MEP. For this test to work, operators need to configure ETH-test parameters on both sender and receiver nodes. The ETH-test then can be done using the following OAM commands: 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 205...
  • Page 211 {allDef | macRemErrXcon | remErrXcon | errXcon | xcon | noXcon} Context config>eth-tunnel>path>eth-cfm>mep Description This command specifies the lowest priority defect that is allowed to generate a fault alarm. Default remErrXcon Page 206 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 212 0 — 600 shutdown Syntax [no] shutdown Context config>eth-ring>path>eth-cfm>mep Description This command administratively enables or disables the MEP. The no form of this command disables or enables the MEP. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 207...
  • Page 213 ACLs with a SAP or deleting a SAP, so that an entire chunk of 512 entries is available. Page 208 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 214 — Specifies the name of the split horizon group up to 32 characters in length. The string must be composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 209...
  • Page 215 — Specifies the authentication key. Allowed values are any string up to 20 characters long composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes. Page 210 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 216 The no form of this command sets the multiplier to default value Default Parameters multiplier — Specifies the hold time applied on neighbor failure. Values 2 — 25 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 211...
  • Page 217 The no form of this command sets the interval to default value Default 1s (10 hundreds of milliseconds means interval value of 10) Page 212 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 218 — Specifies the system priority to be used in the context of the MC-LAG. The partner system will consider all ports using the same lacp-key, system-id, and system-priority as part of the same LAG. Values 1 — 65535 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 213...
  • Page 219 This command enables the context to configure synchronization parameters. igmp-snooping Syntax [no] igmp-snooping Context config>redundancy>multi-chassis>peer>sync Description This command specifies whether IGMP snooping information should be synchronized with the multi- chassis peer. Default no igmp-snooping Page 214 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 220 [0..4094] sync-tag sync-tag — Specifies a synchronization tag up to 32 characters in length to be used while synchronizing this encapsulation value range with the multi-chassis peer. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 215...
  • Page 221 Multi-Chassis Redundancy Commands Page 216 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 222 The total number of ports currently installed in this chassis. This count does not include the Ethernet ports on the CPMs that are used for man- agement access. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 217...
  • Page 223 Half speed — The fans are operating at half speed. Full speed — The fans are operating at full speed. Number of power The number of power supplies installed in the chassis. supplies Page 218 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 224 Manufacturing string Manufacturing deviations Time of last boot : 2001/06/27 11:14:43 Current alarm state : alarm cleared ------------------------------------------------------------------------------- Environment Information Number of fan trays Number of fans 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 219...
  • Page 225 Number of slots Number of ports : 26 Critical LED state : Off Major LED state : Off Minor LED state : Off Over Temperature state : OK Page 220 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 226 Chassis Information =============================================================================== Environment Information Number of fan trays Number of fans Fan tray number Status : up Speed : half speed =============================================================================== *A:7210-SAS-X>show# *A:7210-SAS-X>show# chassis power-supply 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 221...
  • Page 227 — Displays information for the specified card slot. Default Displays all cards. Values state Displays provisioned and equipped card and MDA information. detail — Displays detailed card information. Default Displays summary information only. Page 222 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 228 =============================================================================== Sample output for 7210 SAS-X: A:7210-SAS-X > show card =============================================================================== Card Summary =============================================================================== Slot Provisioned Equipped Admin Operational Card-type Card-type State State ------------------------------------------------------------------------------- 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 223...
  • Page 229 =============================================================================== Card Summary =============================================================================== Slot Provisioned Type Admin Operational Comments Equipped Type (if different) State State ------------------------------------------------------------------------------- (not provisioned) unprovisioned imm-sas-b-4sfp+ cpm-sf-sas-R12 up/active cpm-sf-sas-R12 up/standby =============================================================================== *A:A6144909484>show# Page 224 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 230 Sample output for 7210 SAS-X: A:7210-SAS-X> show card state =============================================================================== Card State =============================================================================== Slot/ Provisioned Equipped Admin Operational Num Comments Type Type State State Ports MDA ------------------------------------------------------------------------------- iom-sas iom-sas m24-1gb+2-10gb m24-1gb+2-10gb 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 225...
  • Page 231 The date and time the most recent boot occurred. boot Current alarm Displays the alarm conditions for the specific board. state Base MAC address Displays the base MAC address of the hardware component. Page 226 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 232 =============================================================================== *A:MTU-A# Sample Output for 7210 SAS-X: A:7210-SAS-X> show card detail =============================================================================== Card 1 =============================================================================== Slot Provisioned Equipped Admin Operational Card-type Card-type State State ------------------------------------------------------------------------------- iom-sas iom-sas 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 227...
  • Page 233 CLEI code : IPMNX10GRA Serial number : NS1034F0924 Manufacture date : 08312010 Manufacturing string Manufacturing deviations : D01696 D01669 Administrative state : up Operational state : up Page 228 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 234 Time of last boot : 2010/07/06 11:29:53 Current alarm state : alarm cleared Base MAC address : 00:25:ba:01:cc:30 Last bootup reason : hardReboot Memory capacity : 1,024 MB =============================================================================== 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 229...
  • Page 235 The compact flash model number. Not user modifiable. Model number The amount of space available on the compact flash card. Size The amount of space remaining on the compact flash card. Free space Page 230 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 236 Config file version : WED JUN 27 11:12:21 2008 UTC Config file last modified : 2008/06/27 11:42:06 Config file last saved : N/A M/S clocking ref state : primary 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 231...
  • Page 237 : up Operational state : up Serial number : serial-1 Firmware revision : v1.0 Model number : Flash 1 Size : 110,984 KB Free space : 88,548 KB Page 232 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 238 Displays provisioned and equipped card and MDA information. active-resource-profile — With this parameter, the show command displays the active resource profile currently in use by the system. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 233...
  • Page 239 Resource (with 64-bit IP addresses) classification. See the Router Configuration guide for more details. Eth CFM Resources allocated towards Ethernet CFM (UP MEP, DOwn MEP, MIPs, etc.). Page 234 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 240 IPv6 64 bit Resource : max ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Eth CFM : 1 (def) ------------------------------------------------------------------------------- down-mep up-mep : disable ------------------------------------------------------------------------------- Sap Egress QoS resource : 1 (def) ------------------------------------------------------------------------------- 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 235...
  • Page 241 The MDA slot number. Provisioned MDA- The MDA type provisioned. type Equipped MDA- The MDA type actually installed. type Admin State Up — Administratively up. Down — Administratively down. Page 236 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 242 Indicates the source for the timing used by the MDA. selected Sync interface Indicates whether the MDA has qualified one of the timing signals timing status from the CPMs. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 237...
  • Page 243 Base MAC address The base chassis Ethernet MAC address. Special purpose MAC addresses used by the system software are constructed as offsets from this base address. Page 238 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 244 MDA Specific Data Maximum port count : 26 Number of ports equipped : 26 Network ingress queue policy : default Capabilities : Ethernet Hardware Data Part number : 3HE05170AAAA0501 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 239...
  • Page 245 Current alarm state : alarm cleared Base MAC address : 00:25:ba:01:cc:32 ------------------------------------------------------------------------------- QOS Settings ------------------------------------------------------------------------------- Ing. Named Pool Policy : None Egr. Named Pool Policy : None Page 240 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 246 =============================================================================== Sample Output for 7210 SAS-T A:SAST>show# mda detail =============================================================================== MDA 1/1 detail =============================================================================== Slot Provisioned Type Admin Operational Equipped Type (if different) State State ------------------------------------------------------------------------------- m12-sfp+10-tx+4-xfp 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 241...
  • Page 247 : mda-1 Manufacture date : 01012003 Manufacturing string : Sim MfgString mda-1 Manufacturing deviations : Sim MfgDeviation mda-1 Manufacturing assembly number : 01-2345-67 Administrative state : up Page 242 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 248 : 20:8a:02:01:00:01 Firmware version : N/A =============================================================================== A:dut-a>show# pools Syntax pools mda-id [/port] [<access-app> [<pool-name>]] pools mda-id [/port] [<network-app> [[pool-name]] Context show Description This command displays pool information. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 243...
  • Page 249 Displays the total pool size. Pool Total Displays the amount of the pool which is shared. Pool Shared Specifies the percentage of reserved pool size. Pool Resv Page 244 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 250 Down Queue7 Down Queue8 Down ------------------------------------------------------------------------------- Non Tcp Slope ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- QueueId State Start-Avg(%) Max-Avg(%) Max-Prob(%) ------------------------------------------------------------------------------- Queue1 Down Queue2 Down Queue3 Down Queue4 Down Queue5 Down 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 245...
  • Page 251 *A:MTU-A# show pools 1/1/1 network-egress =============================================================================== Pool Information =============================================================================== Port : 1/1/1 (lag-1) Application : Net-Egr Pool Name : default Resv CBS : Sum ------------------------------------------------------------------------------- High Slope Page 246 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 252 : 89 KB Pool Resv : 68 KB Pool Total In Use : 0 KB Pool Shared In Use : 0 KB Pool Resv In Use : 0 KB 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 247...
  • Page 253 100032 1000448 1/1/1 131328 100000 1000000 262656 100032 1000448 1/1/1 131328 100000 1000000 262656 100032 1000448 1/1/1 131328 200000 1000000 262656 200064 1000448 1/1/1 131328 200000 1000000 Page 248 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 254 1000000 131328 200064 1000448 1/1/1 131328 200000 1000000 131328 200064 1000448 1/1/1 131328 50000 1000000 131328 50016 1000448 1/1/1 131328 50000 1000000 131328 50016 1000448 =============================================================================== *A:7210SAS>show# 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 249...
  • Page 255 Port Output — The following tables describe port output fields: • General Port Output Fields on page 251 • Entering port ranges: on page 173 • Specific Port Output Fields on page 255 Page 250 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 256 QinQ — Encapsulation type specified for QinQ Access SAPs. Port Type The type of port or optics installed. SFP/MDI MDX GIGE — Indicates the GigE SFP type. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 251...
  • Page 257 : 12/16/2008 18:28:52 Hold time down : 0 seconds Last Cleared Time : 12/16/2008 18:28:51 IP MTU : 1000 =============================================================================== *A:ALU-211# *A:7210SAS>show# port ============================================================================== Ports on Slot 1 ============================================================================== Page 252 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 258 : 0 seconds Last Cleared Time : N/A DDM Events : Enabled Configured Mode : network Encap Type : null Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 253...
  • Page 259 Link Length support: 550m for 50u MMF; 270m for 62.5u MMF =============================================================================== Traffic Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Octets Packets Errors =============================================================================== =============================================================================== Port Statistics =============================================================================== Input Output Page 254 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 260 Down — The port is operationally down. Additionally, the lag-id of the LAG it belongs to in addition to the status of the LAG member (active or standby) is specified. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 255...
  • Page 261 True — The link attempts to automatically negotiate the link speed and duplex parameters. False — The duplex and speed values are used for the link. Alarm State The current alarm state of the port. Page 256 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 262 A text description of the port. Description Interface The port ID displayed in the slot/mda/port format. Speed The speed of the interface Link-level Ethernet — The port is configured as Ethernet. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 257...
  • Page 263 True — The link attempts to automatically negotiate the link speed and duplex parameters. False — The duplex and speed values are used for the link. Alarm State The current alarm state of the port. Page 258 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 264 For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 259...
  • Page 265 Tx Quality Level Indicates which QL value is being transmitted out of the interface. SSM Code Type Indicates the SSM code type in use on the port. Page 260 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 266 Specifies the port scheduler policy or that the default policy default is Egr. Sched. Pol in use. Encap Type Null — Ingress frames will not use any tags or labels to delineate a service. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 261...
  • Page 267 The amount of ingress buffer space, expressed as a percentage of the Size available buffer space, that will be allocated to the port for ingress buffering. Configured The base chassis Ethernet MAC address. Address Page 262 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 268 For any interface that does not support protocol multiplexing, this counter will always be 0. LLF Admin State Displays the Link Loss Forwarding administrative state. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 263...
  • Page 269 Retry : 120 Down On Int. Error : Disabled CRC Mon SD Thresh : Enabled CRC Mon Window : 10 seconds CRC Mon SF Thresh : Enabled Page 264 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 270 Config Speed : 1 Gbps Admin State : up Oper Duplex : full Oper State : up Config Duplex : full Physical Link : Yes : 9212 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 265...
  • Page 271 =============================================================================== Input Output ------------------------------------------------------------------------------- Octets 72974 20243 Packets Errors =============================================================================== * indicates that the corresponding row element may have been truncated. =============================================================================== Port Statistics =============================================================================== Input Output Page 266 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 272 Down On Int. Error : Disabled CRC Mon SD Thresh : Enabled CRC Mon Window : 10 seconds CRC Mon SF Thresh : Enabled Configured Address : 00:25:ba:01:b7:f2 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 267...
  • Page 273 Output ------------------------------------------------------------------------------- Unicast Packets Multicast Packets Broadcast Packets Discards Unknown Proto Discards =============================================================================== =============================================================================== Ethernet-like Medium Statistics =============================================================================== Alignment Errors : Sngl Collisions FCS Errors Mult Collisions Page 268 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 274 Encap Type : null Dot1Q Ethertype : 0x8100 QinQ Ethertype : 0x8100 PBB Ethertype : 0x88e7 Ing. Pool % Rate : 100 Egr. Pool % Rate : 100 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 269...
  • Page 275 Jabbers Collisions Octets 93217 Packets Packets of 64 Octets Packets of 65 to 127 Octets Packets of 128 to 255 Octets Packets of 256 to 511 Octets Page 270 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 276 Drop Stats Egress Queue 6 (ef) Fwd Stats Drop Stats Egress Queue 7 (h1) Fwd Stats Drop Stats Egress Queue 8 (nc) Fwd Stats Drop Stats =============================================================================== *A:MTU-A# 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 271...
  • Page 277 ------------------------------------------------------------------------------- Octets 1556859 1766709 Packets 18523 5849 Errors =============================================================================== * indicates that the corresponding row element may have been truncated. =============================================================================== Port Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Page 272 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 278 Sync. Status Msg. : Disabled Rx Quality Level : N/A Code-Type : SDH Tx Quality Level : N/A Tx DUS/DNU : Disabled Down On Int. Error : Disabled 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 273...
  • Page 279 Packets of 1519 or more Octets : =============================================================================== * indicates that the corresponding row element may have been truncated. =============================================================================== Port Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Unicast Packets Multicast Packets Broadcast Packets Discards Page 274 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 280 Fwd Stats Drop Stats Egress Queue 6 (ef) Fwd Stats Drop Stats Egress Queue 7 (h1) Fwd Stats Drop Stats Egress Queue 8 (nc) Fwd Stats Drop Stats 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 275...
  • Page 281 Cfg Alarm : ais los Alarm Status =============================================================================== =============================================================================== Traffic Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Octets 3853385856 363722496 Packets 20069718 1894388 Errors =========================== DS1/E1 Line =========================== --------------------------- SEFS Page 276 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 282 Signal Fill Type : n/a Signal Pattern : N/A =============================================================================== =============================================================================== Traffic Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Octets 3854167488 364504128 Packets 20073789 1898459 Errors =============================================================================== Port Statistics =============================================================================== 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 277...
  • Page 283 TX Laser Wavelength: 850 nm Diag Capable : yes Connector Code : LC Vendor OUI : 00:90:65 Manufacture date : 2010/05/28 Media : Ethernet Serial Number : PHN661L Page 278 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 284 Late Collisions Excess Collisns Too long Frames Int MAC Tx Errs Symbol Errors Int MAC Rx Errs =============================================================================== *A:MTU-T1>show# *A:MTU-T1>show# port 1/1/6 detail =============================================================================== Ethernet Interface =============================================================================== 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 279...
  • Page 285 High Warn Low Warn Low Alarm ------------------------------------------------------------------------------- Temperature (C) +26.2 +95.0 +90.0 -20.0 -25.0 Supply Voltage (V) 3.25 3.90 3.70 2.90 2.70 Tx Bias Current (mA) 17.0 14.0 Page 280 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 286 Sngl Collisions FCS Errors Mult Collisions SQE Test Errors Late Collisions Excess Collisns Too long Frames Int MAC Tx Errs Symbol Errors Int MAC Rx Errs =============================================================================== 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 281...
  • Page 287 Oper Speed : N/A Link-level : Ethernet Config Speed : 1 Gbps Admin State : down Oper Duplex : N/A Oper State : down Config Duplex : full Page 282 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 288 2.80 Tx Bias Current (mA) 70.0 60.0 Tx Output Power (dBm) -40.00 3.00 1.00 -5.50 -7.50 Rx Optical Power (avg dBm) -40.00 0.00 -1.00 -21.49 -22.44 =============================================================================== 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 283...
  • Page 289 Mult Collisions SQE Test Errors Late Collisions Excess Collisns Too long Frames Int MAC Tx Errs Symbol Errors Int MAC Rx Errs =============================================================================== =============================================================================== Meter Statistics =============================================================================== Page 284 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 290 Oper Speed : N/A Link-level : Ethernet Config Speed : 1 Gbps Admin State : up Oper Duplex : N/A Oper State : down Config Duplex : full 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 285...
  • Page 291 : FCMJ-8521-3-A5 Optical Compliance : GIGE-T Link Length support: 100m for copper =============================================================================== Traffic Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Octets 1408 Packets Errors =============================================================================== Ethernet Statistics =============================================================================== Page 286 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 292 : 04/29/2001 06:59:15 Hold time down : 0 seconds Last Cleared Time : 04/28/2001 03:09:37 DDM Events : Enabled Configured Mode : access Encap Type : QinQ 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 287...
  • Page 293 -5.67 -1.00 -2.00 -10.00 -11.00 Rx Optical Power (avg dBm) -1.87 -1.00 -2.00! -23.01 -24.01 =============================================================================== =============================================================================== Traffic Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Octets 9670292997181 Packets 142210189554 Page 288 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 294 Undersize Pckets The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 289...
  • Page 295 The number of packets received that were equal to or less than the dis- played octet limit. Sample Output =============================================================================== Ethernet Statistics =============================================================================== Broadcast Pckts Drop Events Multicast Pckts 15863 CRC/Align Errors : Undersize Pckts Fragments Page 290 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 296 The number of times that the SQE TEST ERROR is received. The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 291...
  • Page 297 Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Align- ment Error). Page 292 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 298 For any interface that does not support protocol multi- plexing, this counter will always be 0. Unknown proto Discards do not show up in the packet counts. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 293...
  • Page 299 The port ID displayed in the slot/mda/port format. Oper Speed The operating speed of the interface. Link-level Ethernet — the port is configured as Ethernet. Config Speed The configured speed of the interface. Page 294 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 300 The maximum amount of egress bandwidth (in kilobits per second) that this Ethernet interface can generate. Loopback The type of loopback configured on the port, either line,internal, or none. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 295...
  • Page 301 Oper State : up Config Duplex : full Physical Link : Yes : 1514 Single Fiber Mode : No IfIndex : 67141632 Hold time up : 0 seconds Page 296 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 302 Port Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Unicast Packets Multicast Packets Broadcast Packets 2256 Discards Unknown Proto Discards =============================================================================== =============================================================================== Ethernet-like Medium Statistics =============================================================================== Alignment Errors : Sngl Collisions 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 297...
  • Page 303 Port Show Commands FCS Errors Mult Collisions SQE Test Errors Late Collisions Excess Collisns Too long Frames Int MAC Tx Errs Symbol Errors Int MAC Rx Errs =============================================================================== A:7210>show# Page 298 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 304 Configured Address : 7c:20:64:ad:00:f0 Hardware Address : 7c:20:64:ad:00:f0 Cfg Alarm Alarm Status =============================================================================== Traffic Statistics =============================================================================== Input Output ------------------------------------------------------------------------------- Octets 411179 Packets 5415 Errors =============================================================================== =============================================================================== Port Statistics 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 299...
  • Page 305 The alarms that have alarm reporting enabled. Alarm Status The current alarm state (for example, stray, malformed, packet loss, overrun, underrun, remote packet loss, remote fault, or remote RDI). Page 300 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 306 : Unstruct. T1 Bit-rate : 24 Payload Size : 192 Jitter Buffer (ms) Jitter Buffer (packets): 6 Playout Threshold (packets): 4 Use RTP Header : No Differential : No 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 301...
  • Page 307 -548 07/06/2010 19:15:50 -549 07/06/2010 19:14:50 -549 07/06/2010 19:13:50 -550 07/06/2010 19:12:50 -549 07/06/2010 19:11:50 -548 ------------------------------------------------------------------------------- (~ - indicates an invalid interval) ------------------------------------------------------------------------------- Current 24 Hour Page 302 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 308 : Disabled DEI Classificati*: Disabled Split Horizon Group: (Not Specified) Down-when-looped : Disabled Keep-alive : 10 Loop Detected : False Retry : 120 Use Broadcast Addr : False 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 303...
  • Page 309 Sngl Collisions FCS Errors Mult Collisions SQE Test Errors Late Collisions Excess Collisns Too long Frames Int MAC Tx Errs Symbol Errors Int MAC Rx Errs =============================================================================== Page 304 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 310 EapLogoffs While Connecting Logoffs While Connecting Success While Authenticating Timeouts While Authenticating Failures While Authenticating Reauths While Authenticating EapStarts While Authenticating EapLogoffs While Authenticating Reauths While Authenticated 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 305...
  • Page 311 Max auth requests Transmit period Supplicant time- Server timeout Quiet period Radius-plcy Dot1x-Tunnel authentication method last session id last session time last session username last session term cause Page 306 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 312 Enters Connect- EapLogoffs While Connecting Logoffs While Connecting Success While Authenticating Timeouts While Authenticating Failures While Authenticating 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 307...
  • Page 313 Description This command displays Link Layer Discovery Protocol (LLDP) information. Parameters nearest-bridge — Displays nearest bridge information. nearest-non-tpmr — Displays nearest Two-Port MAC Relay (TPMR) information. Page 308 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 314 Management Address Transmit Configuration: Index 1 (system) : Disabled Address : Not Configured Port LLDP Stats: Tx Frames Tx Length Err Frames Rx Frames Rx Frame Discard 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 309...
  • Page 315 All rights reserved. All use subject to applicable license agreements. Built on Tue Sep 28 18:24:07 PDT 2010 by builder in /rel8.0/b1/R5/panos/main Remote Peer Index 143 management addresses at time 06/10/2010 00:23:22: Page 310 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 316 State ------------------------------------------------------------ 1/1/19 Disabled NotApplicable None (0 W) 1/1/20 Disabled NotApplicable None (0 W) 1/1/21 Disabled NotApplicable None (0 W) 1/1/22 Disabled NotApplicable None (0 W) ============================================================ 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 311...
  • Page 317 Internal Loopback Port Status =============================================================================== Port Loopback Application Service Type Enabled ------------------------------------------------------------------------------- 1/1/12 Physical Mac-Swap 1/1/25 Virtual Mac-Swap ======================================== Mac-swap Application Status ======================================== Enabled : Yes Test Service Id Page 312 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 318 ======================================== Enabled : Yes Test Service Id : None Test Sap Id : None ======================================== ========================================================== Sample Output for 7210 SAS-R6 and 7210 SAS-R12 *A:7210SAS>show>system# internal-loopback-ports detail 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 313...
  • Page 319 The source MAC address that is used in the configuration of port Loopback Src loopback mac-swap test. Addr The destination MAC address that is used in the configuration of port Loopback Dst loopback mac-swap test. Addr Page 314 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 320 Up — The LAG is operationally up. Down — The LAG is operationally down. The number of operational links for the LAG at or below which the Port-Threshold configured action will be invoked. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 315...
  • Page 321 The hardware address. Hold-Time Down The timer, in tenths of seconds, which controls the delay between detecting that a LAG is down and reporting it to the higher levels. Page 316 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 322 (LACP) Mode LACP active or passive mode. LACP xmit LACP transmits on standby links enabled / disabled. standby Slave-to-partner Configured enabled/disabled. Port-id Displays the member port ID. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 317...
  • Page 323 Forced Prio ------------------------------------------------------------------------------- 1/1/3 active 32768 1/1/4 active 32768 ------------------------------------------------------------------------------- Port-id Role Dist Aggr Timeout Activity ------------------------------------------------------------------------------- 1/1/3 actor 1/1/3 partner 1/1/4 actor 1/1/4 partner =============================================================================== *A:dut-c# Page 318 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 324 Lag-id Port-id Input Input Output Output Input Output Bytes Packets Bytes Packets Errors Errors ------------------------------------------------------------------------------- 1/1/3 1006 2494 1/1/4 1/1/5 9968 9833 ------------------------------------------------------------------------------- Totals 11409 12728 =============================================================================== ALA-1# 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 319...
  • Page 325 Prtr Oper Key : 32769 ------------------------------------------------------------------------------- Port-id Act/Stdby Opr Primary Sub-group Forced Prio ------------------------------------------------------------------------------- 1/1/5 active 32768 1/1/6 active 32768 ------------------------------------------------------------------------------- Port-id Role Dist Aggr Timeout Activity Page 320 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 326 3/1/1 down active down 10/100/Gig Ethernet SFP 5/1/4 active 10/100/Gig Ethernet SFP =============================================================================== *A:7210SAS>show# LAG Port Output — The following table describes detailed LAG statistics output fields. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 321...
  • Page 327 ------------------------------------------------------------------------------- 1/1/3 active 32768 1/1/5 active 32768 2/1/3 active 32768 2/1/4 active 32768 ------------------------------------------------------------------------------- Once subgroups are configured: ------------------------------------------------------------------------------- Port-id Act/Stdby Oper Primary Sub-grp Forced Prio Fld-Port Page 322 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 328 — Displays the address of the multi-chassis peer. lag lag-id — Displays the specified LAG ID on this system that forms an multi-chassis LAG configuration with the indicated peer. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 323...
  • Page 329 Packets Dropped Out of Seq Packets Dropped Unknown Tlv Packets Dropped MD5 Packets Tx : 9229 Packets Tx Keepalive : 8705 Packets Tx Peer Config : 509 Packets Tx Failed Page 324 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 330 DHCP Server instances synced on peer 3.3.3.3 =============================================================================== Router-Name Server-Name ------------------------------------------------------------------------------- No instances found =============================================================================== mc-lag Syntax mac-lag peer ip-address [lag lag-id] mac-lag [peer ip-address [lag lag-id]] statistics 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 325...
  • Page 331 Hold On Ngbr Failure : 3 ------------------------------------------------------------------------------- Lag Id Lacp Remote System Id Last State Changed Lag Id Prio ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- No LAGs found =============================================================================== *7210-SAS>show>redundancy>multi-chassis# ^C Page 326 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 332 A:ALA-12>monitor# port 1/4 interval 3 repeat 3 absolute =============================================================================== Monitor statistics for Port 1/4 =============================================================================== Input Output ------------------------------------------------------------------------------- At time t = 0 sec (Base Statistics) ------------------------------------------------------------------------------- 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 327...
  • Page 333 At time t = 6 sec (Mode: Rate) ------------------------------------------------------------------------------- Octets Packets Errors ------------------------------------------------------------------------------- At time t = 9 sec (Mode: Rate) ------------------------------------------------------------------------------- Octets Packets Errors =============================================================================== A:ALA-12>monitor# *A:ces-A# monitor port 1/2/1 Page 328 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 334 Utilization (% of port capacity) 99.99 99.99 *A:ces-A# monitor port 1/2/1 absolute =============================================================================== Monitor statistics for Port 1/2/1 =============================================================================== Input Output ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- At time t = 0 sec (Base Statistics) 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 329...
  • Page 335 At time t = 6 sec (Mode: Absolute) ------------------------------------------------------------------------------- Octets 1408 Packets Errors ------------------------------------------------------------------------------- At time t = 9 sec (Mode: Absolute) ------------------------------------------------------------------------------- Octets 1408 Packets Errors =============================================================================== A:7210-SAS-X>monitor# Page 330 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 336 Description This command clears port statistics for the specified port(s). Parameters port-id — The port identifier. Values statistics — Specifies that port statistics will be cleared. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 331...
  • Page 337 Port Monitor Commands slot — The slot number. Values mda — The MDA number. Default All MDAs. Values 1, 2 Page 332 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 338 — Specifies to display trace LACP selection logic. mc — Specifies to display multi-chassis parameters. mc-pkt — Specifies to display the MC-LAG control packets with valid authentication were received on this system. 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 333...
  • Page 339 Port Monitor Commands Page 334 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...
  • Page 340 Standards and Protocol Support NOTE: The capabilities available when operating in access-uplink mode/L2 mode and network mode/MPLS mode are different. Correspondingly, not all the standards and protocols listed below are applicable to access-uplink mode and network mode. Standards Compliance RFC 2385 Protection of BGP Sessions via MD5 DHCP RFC 2439 BGP Route Flap Dampening...
  • Page 341 Standards and Protocols RFC 2464 Transmission of IPv6 Packets MPLS - General RFC 6426 MPLS On-Demand over Ethernet Networks Connectivity and Route Tracing RFC 3031 MPLS Architecture RFC 2545 Use of BGP-4 Multiprotocol RFC 6478 Pseudowire Status for Static RFC 3032 MPLS Label Stack Encoding Extension for IPv6 Inter-Domain Pseudowires RFC 4379 Detecting Multi-Protocol...
  • Page 342 Standards and Protocols RFC 2206 RSVP-MIB RFC 4577 OSPF as the Provider/ draft-ietf-secsh-userauth.txt SSH Customer Edge Protocol for BGP/ Authentication Protocol RFC 2571 SNMP-FRAMEWORKMIB MPLS IP Virtual Private Networks draft-ietf-secsh-transport.txt SSH RFC 2572 SNMP-MPD-MIB (VPNs) Transport Layer Protocol RFC 2573 SNMP-TARGET-&- draft-ietf-secsh-connection.txt SSH NOTIFICATION-MIB PSEUDO-WIRE...
  • Page 343 Standards and Protocols ITU-T G.8262 Telecommunication TIMETRA-SAS-IEEE8021-PAE- Standardization Section of ITU, MIB.mib Timing characteristics of TIMETRA-SAS-GLOBAL-MIB.mib synchronous Ethernet equipment TIMETRA-SAS-LOG-MIB.mib.mib slave clock (EEC), issued 08/2007. TIMETRA-SAS-MIRROR-MIB.mib ITU-T G.8264 Telecommunication TIMETRA-SAS-MPOINT-MGMT- Standardization Section of ITU, MIB.mib (Only for 7210 SAS-X) Distribution of timing information TIMETRA-SAS-PORT-MIB.mib through packet networks, issued 10/ TIMETRA-SAS-QOS-MIB.mib...
  • Page 344 Standards and Protocols Standards and Protocols Page 339...
  • Page 345 Standards and Protocols Page 340 Standards and Protocols...
  • Page 346 Ethernet multi-chassis LAG access port network port command reference card commands port types MDA commands preprovisioning guidelines port commands TDM commands 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide Page 341...
  • Page 347 Page 342 7210 SAS M, T, X, R6, R12, Mxp Interface Configuration Guide...

This manual is also suitable for:

7210 sas t7210 sas x7210 sas r67210 sas mxp os7210 sas r12

Table of Contents