Register Overview - Beckhoff KL3208 Manual

5.3

Register overview

The registers are used for parameterizing the Bus Terminals and are once available for each channel. They
can be read or written by means of register communication [} 46].
Register no. Comment
A/D converter, raw value
R0 [} 42]
A/D converter, raw value of the line
R1 [} 42]
R2 reserved
... ...
R5 reserved
Diagnostic register
R6 [} 42]
Command register (not used)
R7 [} 42]
Terminal type
R8 [} 42]
Firmware version
R9 [} 42]
R10 Multiplex shift register
R11 Signal channels
R12 minimum data length of a channel
R13 Data structure
R14 reserved
R15 Alignment register
Hardware version number
R16 [} 42]
Vendor calibration: Offset
R17 [} 42]
Vendor calibration: Gain
R18 [} 42]
Manufacturer scaling: Offset
R19 [} 43]
Manufacturer scaling: Gain
R20 [} 43]
R21 Offset register two-wire connection method
R22...R28 reserved
R29 Terminal type - special identifica-
tion
R30 reserved
Code word register
R31 [} 43]
Feature register
R32 [} 43]
User scaling: Offset
R33 [} 44]
User scaling: Gain
R34 [} 44]
R35...R36 ...
Filter constant of the A/D con-
R37 [} 44]
verter
R38 reserved
Further elements
R39 [} 44]*
Conversion time for all channels
R40 [} 45]*
B-parameter for user-defined NTC
R41 [} 45]*
Resistance at 25 °C for user-defined NTC
R42 [} 45]*
Reference temperature for user-defined NTC
R43 [} 45]*
Lower range limit for user-defined NTC
R44 [} 45]*
Upper range limit for user-defined NTC
R45 [} 45]*
R46...R63 reserved
*) Supported only by KL3208-0010 from firmware version 1C and hardware version 01
KL3208, KL3228/KS3228
Default value
variable
variable
0x0000
...
0x0000
0x0000
0x0000
KL3208-0010 0x0C88
KL3228-0000 0x0C9C
e.g. 0x3141
0x0218 / 0x0130
0x0218
0x0098
0x0000
-
variable
e.g. 0x0000
specific
specific
0x0000
0x0100
specific
0x0000
KL3208-0010 0x000A
KL3228-0000 0x0000
0x0000
0x0000
KL3208-0010 0x0020
KL3228-0000 0x0000
0x0000
0x0100
...
KL3208-0010 0x0000
KL3228-0000 0x0138
0x0000
0x0000
0x000A
0x0F78
0x03E8
0x0019
0xFFD8
0x0082
0x0000
Version: 3.3.0
Access from the user program
R/W Memory
variable R RAM
variable R RAM
0 R RAM
dec
... ... -
0 R RAM
dec
0 R RAM
dec
0 R/W RAM
dec
3208 R ROM
dec
3228
dec
e.g. 12609 R ROM
dec
536 / 304 R ROM
dec dec
536 R ROM
dec
152 R ROM
dez
0 R ROM
dec
- - -
variable R/W RAM
e.g. 0 R/W SEEPROM
dec
specific R/W SEEPROM
specific R/W SEEPROM
0 R/W SEEPROM
dec
256 R/W SEEPROM
dec
specific R/W SEEPROM
0 R/W SEEPROM
dec
0010 R ROM
dec
0000
dec
0 R/W SEEPROM
dec
0 R/W RAM
dec
32 R/W SEEPROM
dec
0
dec
0 R/W SEEPROM
dec
256 R/W SEEPROM
dec
... - -
0 R/W SEEPROM
dec
312 R/W SEEPROM
dec
0 R/W SEEPROM
dec
0 R/W SEEPROM
dec
10 R/W SEEPROM
dec
3960 R/W SEEPROM
dec
1000 R/W SEEPROM
dec
25 R/W SEEPROM
dec
65496 R/W SEEPROM
dec
130 R/W SEEPROM
dez
0 R/W SEEPROM
dec
41