This addendum provides guidance for establishing HART communication, and describes the HART menu structure when using the X9800 with a HART Handheld Communicator, a PC, or other process interface device that...
Page 4
+ Vin B2468 B2466 – Vin – Vin Figure 4—X9800 Detector Wired for Isolated 0 to 20 mA Current Figure 2—X9800 Detector Wired for Isolated 0 to 20 mA Current Output (Sinking) Output (Sourcing) *Nominal input impedance of PLC = 250 ohms.
In the event that your Communicator does not establish communications with the X9800, ensure HIB Hdwr Flt that the appropriate DDs for the X9800 have been When a HART field communicator is first connected programmed into your Communicator. To review the to the detector, a "HIB Hdwr Flt"...
HART MENU STRUCTURE HART PV Menu X9800 Root Menu Device Info Menu General Info Menu 1) Fire (Yes/No) 1) General Info Menu 1) PV Unit 1) Manufacturer 2) Fault (Yes/No) 2) HART Info Menu 2) PV 2) Model 3) Device Info Menu...
X9800 ROOT MENU When HART communication is established, the first menu displayed is the X9800 Root menu: X9800 Root Menu 1) Fire (Yes/No) 2) Fault (Yes/No) 3) Device Info Menu 4) Command Menu 5) Device Setup Menu Indicates “Y” if the device is in a fire alarm status — analog output is at 20 mA, 1) Fire (Yes/No) fire alarm relay is actuated, and LED is red.
GENERAL INFO MENU General Info Menu 1) Manufacturer X9800 Root Menu Device Info Menu 2) Model 1) Fire (Yes/No) 1) General Info Menu 3) Serial Number 2) Fault (Yes/No) 2) HART Info Menu 4) Part Number 3) Device Info Menu...
HART INFO MENU HART Info Menu 1) Universal rev 2) Field dev rev X9800 Root Menu Device Info Menu 3) Final asmbly num 1) Fire (Yes/No) 1) General Info Menu 4) Tag 2) Fault (Yes/No) 2) HART Info Menu 5) Long tag...
4) PV USL Not implemented for X9800. 5) PV LSL Not implemented for X9800. 6) PV Minimum Span Not implemented for X9800. 7) PV Damp Not implemented for X9800. 8) PV AO Analog Output. The value that tracks the Digital Value representation, under normal operating modes.
CONDENSED STATUS HART Info Menu 1) Universal rev Condensed Status 2) Fld dev rev X9800 Root Menu Device Info Menu 1) Xmtr Addstatus 0 3) Final asmbly num 1) Fire (Yes/No) 1) General Info Menu 2) Xmtr Addstatus 1 4) Tag...
Status Info Menu 1) Warm Up (Y/N) 2) Fire (Y/N) 3) IR Alarm (Y/N) 4) TDSA Alarm (Y/N) X9800 Root Menu Device Info Menu 5) Quick Alarm (Y/N) 1) Fire (Yes/No) 1) General Info Menu 6) IR Pre Alarm (Y/N)
Status Info Menu 1) Warm Up (Y/N) 2) Fire (Y/N) 3) IR Alarm (Y/N) 4) TDSA Alarm (Y/N) Hardware Menu X9800 Root Menu Device Info Menu 5) Quick Alarm (Y/N) 6) IR Pre Alarm (Y/N) 1) Temperature 1) Fire (Yes/No)
Status Info Menu 1) Warm Up (Y/N) 2) Fire (Y/N) 3) IR Alarm (Y/N) 4) TDSA Alarm (Y/N) Oi Menu X9800 Root Menu Device Info Menu 5) Quick Alarm (Y/N) 1) Consecutive IR Oi Fails 1) Fire (Yes/No) 1) General Info Menu...
DETECTOR SETTINGS This menu shows factory settings relating to relay operation, detector sensitivity, and response. Detector Settings 1) IR Mode 2) IR Sensitivity X9800 Root Menu Device Info Menu 3) Auto Oi Enabled 1) Fire (Yes/No) 1) General Info Menu...
COMMAND MENU The Command Menu allows the operator to initiate a manual o i test and also to perform various reset/ clear functions. Command Menu X9800 Root Menu 1) Start Passive Oi 2) Start Active Oi 1) Fire (Yes/No) 3) Clear Oi Fault...
HART COMMAND MENU The HART Command Menu allows the operator to perform diagnostic and service functions as follows: Command Menu X9800 Root Menu 1) Start Passive Oi HART Command Menu 1) Fire (Yes/No) 2) Start Active Oi 2) Fault (Yes/No)
CONFIGURATION MENU Device Setup Menu X9800 Root Menu Configuration Menu 1) Configuration Menu 1) Fire (Yes/No) 2) Calibration Menu 1) Cons IR Oi Fails 2) Fault (Yes/No) 3) Write Protect 2) Time Delay 3) Device Info Menu 4) HART Setup...
The device is provided from the factory with Write Protect off. With Write Protect on, the use of a password is required to enable writing to the device. Device Setup Menu X9800 Root Menu Write Protect 1) Configuration Menu...
HART SETUP This menu allows editing of the following functions: HART Setup Device Setup Menu X9800 Root Menu 1) Poll addr 1) Configuration Menu 1) Fire (Yes/No) 2) Final asmbly num 2) Calibration Menu 2) Fault (Yes/No) 3) Tag 3) Write Protect...