Teledyne 200A Instruction Manual page 5

Teledyne API Model 200A NO
7.8.9 Summary of Quality Assurance Checks ............................................................................... 7-29
7.8.10 ZERO and SPAN Checks ................................................................................................... 7-30
7.8.11 Recommended Standards for Establishing Traceability..................................................... 7-31
7.8.12 Certification Procedures of Working Standards ................................................................. 7-32
7.9 C
ALIBRATION OF
7.9.1 Zero Calibration with AutoRange or Independent Range .................................................... 7-34
7.9.2 Span Calibration with AutoRange or Independent Range.................................................... 7-34
7.10 C
ALIBRATION
7.11 R ............................................................................................................................... 7-37
EFERENCES
8 MAINTENANCE ........................................................................................................ 8-1
8.1 M
AINTENANCE
8.2 R
EPLACING THE
8.3 R
EPLACING THE
8.4 R
EPLACING THE
8.5 R
EPLACING THE
8.6 R
EPLACING THE
8.7 C
LEANING THE
8.8 P L
NEUMATIC INE
8.9 L C P
EAK HECK ROCEDURE
8.10 L L C
IGHT EAK
8.11 P R
ROM EPLACEMENT
9 TROUBLESHOOTING, ADJUSTMENTS.............................................................. 9-1
9.1 O V
PERATION ERIFICATION
9.1.1 Fault Diagnosis with TEST Variables .................................................................................... 9-3
9.1.2 Fault Diagnosis with WARNING Messages .......................................................................... 9-8
9.1.3 Fault Diagnosis Using DIAGNOSTIC Mode ....................................................................... 9-11
9.1.4 M200A Internal Variables .................................................................................................... 9-18
9.1.5 Test Channel Analog Output ................................................................................................ 9-20
9.1.6 Factory Calibration Procedure .............................................................................................. 9-23
9.2 P
ERFORMANCE
9.2.1 AC Power Check................................................................................................................... 9-27
9.2.2 Flow Check ........................................................................................................................... 9-27
9.2.3 No Response to Sample ........................................................................................................ 9-28
9.2.4 Negative Output .................................................................................................................... 9-29
9.2.5 Excessive Noise .................................................................................................................... 9-29
9.2.6 Unstable Span ....................................................................................................................... 9-30
9.2.7 Unstable Zero........................................................................................................................ 9-31
9.2.8 Inability to Span.................................................................................................................... 9-31
9.2.9 Inability to Zero .................................................................................................................... 9-32
9.2.10 Non-Linear Response ......................................................................................................... 9-33
9.2.11 Slow Response .................................................................................................................... 9-34
9.2.12 Analog Output Doesn't Agree with Display Concentration................................................ 9-34
9.3 S T
UBSYSTEM ROUBLESHOOTING AND
9.3.1 Computer, Display, Keyboard .............................................................................................. 9-35
Analyzer Instruction Manual, 02246, Rev. F1
X
I R
NDEPENDENT ANGES OR
Q .............................................................................................................. 7-35
UALITY
S .............................................................................................................. 8-1
CHEDULE
S P
AMPLE ARTICULATE
O S C
ZONE CRUBBER
P ......................................................................................................... 8-5
ERMEATION
IZS Z A S
ERO IR CRUBBER
M C
OLYBDENUM ONVERTER
R C ..................................................................................................... 8-9
EACTION ELL
I ....................................................................................................... 8-11
NSPECTION
............................................................................................................. 8-15
P ................................................................................................ 8-16
HECK ROCEDURE
P .............................................................................................. 8-16
ROCEDURE
-M200A D
P ............................................................................................................ 9-26
ROBLEMS
A
UTORANGING
F .............................................................................. 8-3
ILTER
.............................................................................. 8-5
HARCOAL
...................................................................................... 8-6
.................................................................................. 8-7
T
IAGNOSTIC ECHNIQUES
A ................................................................... 9-35
DJUSTMENTS
v
........................................................ 7-34
...................................................... 9-3