Teledyne 200A Instruction Manual page 4

Teledyne API Model 200A NO
5.3.1 Configuration Information (CFG)......................................................................................... 5-14
5.3.2 Automatic Calibration (AutoCal) ......................................................................................... 5-14
5.3.3 Data Acquisition System (DAS)........................................................................................... 5-14
5.3.4 Range Menu .......................................................................................................................... 5-16
5.3.5 Password Enable ................................................................................................................... 5-20
5.3.6 Time of Day Clock................................................................................................................ 5-20
5.3.7 Diagnostic Mode................................................................................................................... 5-20
5.3.8 Communications Menu......................................................................................................... 5-20
5.3.9 Variables Menu (VARS) ...................................................................................................... 5-21
5.3.10 M200A Operating Modes ................................................................................................... 5-21
5.4 S O
TATUS UTPUT
5.5 RS-232 I
NTERFACE
5.5.1 Setting Up the RS-232 Interface ........................................................................................... 5-24
5.5.2 Command Summary ............................................................................................................. 5-28
5.5.3 TEST Commands and Messages .......................................................................................... 5-32
5.5.4 WARNING Commands and Messages................................................................................. 5-33
5.5.5 CALIBRATION Commands and Messages ......................................................................... 5-34
5.5.6 DIAGNOSTIC Commands and Messages............................................................................ 5-36
5.5.7 DAS Commands and Message.............................................................................................. 5-37
5.5.8 Internal Variables.................................................................................................................. 5-39
6 OPTIONAL HARDWARE AND SOFTWARE....................................................... 6-1
6.1 R M O
ACK OUNT
6.2 Z /S V
ERO PAN ALVES
6.3 I Z
NTERNAL ERO
6.4 A - S
UTOCAL ETUP OF
6.5 P T
ERMEATION UBE
6.6 4-20 A C
M URRENT
7 CALIBRATION AND ZERO/SPAN CHECKS....................................................... 7-1
7.1 M Z
ANUAL ERO
7.2 M Z
ANUAL ERO
7.3 M Z
ANUAL ERO
7.4 A Z
UTOMATIC ERO
7.5 D Z
YNAMIC ERO
7.6 C
ALIBRATE ON
7.7 U Z /S
SE OF ERO
7.8 EPA P
ROTOCOL
7.8.1 Calibration of Equipment...................................................................................................... 7-12
7.8.2 Calibration Gas and Zero Air Sources.................................................................................. 7-14
7.8.3 Data Recording Device ......................................................................................................... 7-15
7.8.4 Gas Phase Titration (GPT) System....................................................................................... 7-16
7.8.5 Dynamic Multipoint Calibration Procedure ......................................................................... 7-20
7.8.6 Moly Converter Efficiency ................................................................................................... 7-25
7.8.7 Calibration Frequency........................................................................................................... 7-27
7.8.8 Other Quality Assurance Procedures.................................................................................... 7-27
Analyzer Instruction Manual, 02246, Rev. F1
X
........................................................................................................................... 5-22
....................................................................................................................... 5-23
.................................................................................................................. 6-1
PTIONS
....................................................................................................................... 6-1
/S (IZS) ........................................................................................................... 6-3
PAN
IZS Z /S
AND ERO
......................................................................................................................... 6-5
L O .................................................................................................. 6-8
OOP UTPUT
/S C C
PAN HECK OR AL
/S C C
PAN HECK OR ALIBRATION WITH
/S C IZS O
PAN HECK WITH
/S C ..................................................................................................... 7-7
PAN HECK
/S C
PAN ALIBRATION
NO P T
ERMEATION UBE
2
V IZS
PAN ALVES OR WITH
C ..................................................................................................... 7-12
ALIBRATION
V ....................................................................... 6-3
PAN ALVES
W Z /S G
ITH ERO PAN AS IN THE
Z
ERO
............................................................................. 7-7
PTION
.............................................................................................. 7-7
......................................................................................... 7-9
R C
EMOTE ONTACT
iv
S P
AMPLE ORT
/S V O
PAN ALVES PTION
C ...................................... 7-11
LOSURE
...................... 7-4
....................... 7-6