Table of Contents
Advertisement
DSK transition
Operating in the DSK operation area
Press the <DSK1 TRNS> to <DSK4 TRNS> buttons in the transition area to execute a transition automatically with the transition time of respective keys
set on the menu.
The <DSK1 TRNS> to <DSK4 TRNS> buttons flicker during key in, and light when the transition is complete. If the <DSK1 TRNS> to <DSK4 TRNS>
buttons are pressed while key in is complete, transition of the key image (key out) is executed.
The <DSK1 TRNS> to <DSK4 TRNS> buttons light during key out, and go off when the transition is complete. If the <DSK1 TRNS> to <DSK4 TRNS>
buttons are pressed during the transition, the transition direction is reversed.
Setting the DSK transition mode
Transition mode and transition time can be set separately for key in and key out.
1
Select the <DSK MISC> button → [DSK1] to [DSK4] → [Transition] tab.
2
Select an item in [Transition] in the [In Type]/[Out Type] column.
f The transition mode available is only [MIX].
[Off]
[On]
3
Set [Time] in the [In Type]/[Out Type] column.
f Set the transition time.
4
Select an item in [In=Out] in the [Out Type] column.
[Off]
[On]
DSK output
The DSK block outputs the following signals.
For details, refer to "System Menu" (page 125).
f DSKPGM1, DSKPGM2: Outputs program signals of DSK compositions.
Select the <SYS> button on the top menu → [MAIN FRAME] → [DSK] tab → [Config] column → [DSK1] to [DSK4] and set them to either [DSKPGM1]
or [DSKPGM2] to assign the signal to one of the outputs.
f DSKPVW1, DSKPVW2: Outputs DSK preview signals.
Follow the setting of the <SYS> button on the top menu → [MAIN FRAME] → [DSK] tab → [Config] column → [DSK1] to [DSK4], and assign the signal
to either DSKPVW1 or DSKPVW2 line.
Keyers set to [Off] using the <SYS> button on the top menu → [MAIN FRAME] → [DSK] tab → [DSK PVW] column are not combined.
f DSK1CLN, DSK2CLN, DSK3CLN, DSK4CLN: Outputs clean signals before adding key effects from each keyer.
f SEL KEYPVW: Outputs previews of the keys when <KEY1> to <KEY4> buttons and <DSK1> to <DSK4> buttons in the KEY operation area of each
ME are pressed. The preview screen for chrome key adjustment is not output. Keys set to [On] from the <SYS> button on the top menu → [MAIN
FRAME] → [Sel KeyPVW] tab → [ME1]/[ME2]/[DSK] column are combined to images and output. If the button for the key set to [Off] is selected,
images where keys are not combined will be output.
Adjusting the luminance key/linear key
Adjust the luminance key and linear key definition.
1
Select the <DSK MISC> button → [DSK1] to [DSK4] → [Setting] tab.
2
Set [Clip], [Gain], and [Density] in the [DSK Adjust] column.
[Clip]
[Gain]
[Density]
3
Select an item in [Invert] in the [DSK Adjust] column.
[Off]
[On]
DSK decorations
Add a border, shadow, or other edge to the key.
Chapter 5 Basic Operations — DSK (Downstream key)
Disables the transition mode of key in or key out.
Enables the transition mode of key in or key out.
Sets the [In Type] column and the [Out Type] column separately.
Matches the setting of the [Out Type] column to the setting of the [In Type] column.
Sets the reference level for creating key signals.
Sets the key amplitude.
Sets the key density.
Does not invert the key signals generated internally.
Inverts the key signals generated internally.
– 66 –
Advertisement
Table of Contents
