Danfoss VLT AQUA Drive FC 202 Instruction Manual page 85

Specifications
on 4-5 (NO) (Inductive load @ cosφ 0.4)
1)
Max. terminal load (AC-15)
Max. terminal load (DC-1) 1) on 4-5 (NO) (Resistive load)
Max. terminal load (DC-13) 1) on 4-5 (NO) (Inductive load)
1)
Max. terminal load (AC-1) on 4-6 (NC) (Resistive load)
on 4-6 (NC) (Inductive load @ cosφ 0.4)
1)
Max. terminal load (AC-15)
Max. terminal load (DC-1) 1) on 4-6 (NC) (Resistive load)
Max. terminal load (DC-13) 1) on 4-6 (NC) (Inductive load)
Min. terminal load on 1-3 (NC), 1-2 (NO), 4-6 (NC), 4-5 (NO)
Environment according to EN 60664-1
1) IEC 60947 parts 4 and 5
The relay contacts are galvanically isolated from the rest of the circuit by reinforced isolation (PELV).
2) Overvoltage Category II
3) UL applications 300 V AC 2 A
Control card, 10 V DC output
Terminal number
Output voltage
Max. load
The 10 V DC supply is galvanically isolated from the supply voltage (PELV) and other high-voltage terminals.
Control characteristics
Resolution of output frequency at 0–1000 Hz
System response time (terminals 18, 19, 27, 29, 32, 33)
Speed control range (open-loop)
Speed accuracy (open-loop)
All control characteristics are based on a 4-pole asynchronous motor
Surroundings
Enclosure type A
Enclosure type B1/B2
Enclosure type B3/B4
Enclosure type C1/C2
Enclosure type C3/C4
Enclosure type D1/D2/E1
Enclosure type D3/D4/E2
Enclosure kit available ≤ enclosure type A
Vibration test enclosure A/B/C
Vibration test enclosure D/E/F
Max. relative humidity
Aggressive environment (IEC 721-3-3), uncoated
Aggressive environment (IEC 721-3-3), coated
Test method according to IEC 60068-2-43 H2S (10 days)
Ambient temperature
Derating for high ambient temperature, see section on special conditions
Minimum ambient temperature during full-scale operation
Minimum ambient temperature at reduced performance
Temperature during storage/transport
Maximum altitude above sea level without derating
Maximum altitude above sea level with derating
Derating for high altitude, see section on special conditions
EMC standards, Emission
EMC standards, Immunity
®
VLT AQUA Drive
Instruction Manual
5%–95% (IEC 721-3-3; Class 3K3 (non-condensing) during operation
®
MG20M922 - VLT is a registered Danfoss trademark
24 V DC 10 mA, 24 V AC 20 mA
overvoltage category III/pollution degree 2
1:100 of synchronous speed
30-4,000 rpm: Maximum error of ±8 rpm
IP20/Chassis, IP21 kit/Type 1, IP55/Type12, IP66
IP21/Type 1, IP55/Type12, IP66
IP21/Type 1, IP55/Type 12, IP66
IP21/Type 1, IP54/Type12
IP21/TYPE 1/IP4X top
-13 to +149/158 °F [-25 to +65/70 °C]
EN 61800-3, EN 61000-6-3, EN 55011, IEC 61800-3
EN 61800-3, EN 61000-6-1/2,
240 V AC, 0.2 A
80 V DC, 2 A
24 V DC, 0.1 A
240 V AC, 2 A
240 V AC, 0.2 A
50 V DC, 2 A
24 V DC, 0.1 A
50
10.5 V ±0.5 V
25 mA
±0.003 Hz
≤ 2 ms
10
IP20/Chassis
IP20/Chassis
IP00/Chassis
0.035 oz [1.0 g]
0.024 oz [0.7 g]
class 3C2
class 3C3
Max. 122 °F [50 °C]
32 °F [0 °C]
14 °F [-10 °C]
3300 ft [1000 m]
10,000 ft [3000 m]
10-15
10