Product Description And Intended Use; Installation; Verifying The Suitability Of The Gate And Environment; Verifying The Product's Application Limits - Nice Filo Instructions And Warnings For Installation

2

PRODUCT DESCRIPTION AND INTENDED USE

The devices of this kit and other optional accessories belong to the Nice Home automation system and are designed to automate a sliding gate for
residential use.
sidered improper and is forbidden
The kit comprises an electromechanical gearmotor with 24 V direct current
for manually moving the gate in case of a power outage
the automation.
Connection of the control unit to the various devices occurs through the ECSBus system
number of manoeuvres during the hours following a power outage .
3

INSTALLATION

Certain devices and accessories mentioned in this manual are optional and not included in the kit.
The end stops are not included in the kit and do not belong to the Nice Home range of products.
Consult the Nice Home product catalogue or visit the website www.niceforyou.com

3.1 - VERIFYING THE SUITABILITY OF THE GATE AND ENVIRONMENT

the gate' s label.
installation of the gate or poor maintenance of the latter.
• Manually move the gate leaf in both directions (open/closed) and make sure that the movement takes place with constant friction at every point along
• Manually bring the door of the gate into any position then leave it closed and make sure that it does not move.
• Check that there is no risk of derailment or that the gates may come o their guides.
ground.
• Check that the installation surfaces of the various devices are solid for guaranteeing a stable anchorage and that they are protected and guarded

3.2 - VERIFYING THE PRODUCT'S APPLICATION LIMITS

01. Check the overall dimensions of the gearmotor ( Fig. 2
the foundation excavation for the passage of the cable trays.
02. Check that the estimated durability is compatible with the intended use (Paragraph 2.5).
03. Ensure that all limitations, conditions and warnings appearing in this manual can be fully observed.

3.3 - PRODUCT TECHNICAL SPECIFICATIONS

Model type
Product type
Technology adopted
Peak thrust
Nominal torque
Speed (no load)
Nominal torque speed
Maximum frequency of cycles
Maximum continuous cycle time
Application limits
Mains power supply
Maximum power input
Emergency power supply
Flashing light output
A B
Step Step
FILO400C - FILO400CST/AU01 -
FILO400CSP/AU01
Electromechanical gearmotor for automatic gate and door automations with incorporated con -
trol unit, inclusive of radio receiver for ECCO5 transmitters (various models)
A 24 V motor
inside the motor, but separate from the control unit, ( not present in FILO400CSP/AU01 and
FILO600CSP/AU01) reduces the mains voltage to the nominal 24 V
the automation system.
10 Nm
3.5 Nm
0.30 m/s
0.20 m/s
24 cycles/hour at 55°C (40 cycles/hour at
25°C)
30 minutes
Its structural characteristics make it suitable
for use on gates weighing up to 400 kg and
up to 5.5 m long.
230 V (+10% –15%) 50/60Hz (FILO400CST/AU01 / FILO600CST/AU01 250 V~ 50/60 Hz)
FILO400CSP/AU01 / FILO600CSP/AU01 24 V
370 W
(a single cable with 2 wires).
which ensures that the automation can execute a certain
FILO600C - FILO600CST/AU01 -
FILO600CSP/AU01
13 Nm
5.2 Nm
0.20 m/s
0.15 m/s
11 cycles/hour at 55°C (20 cycles/hour at
25°C)
15 minutes
Its structural characteristics make it suitable
for use on gates weighing up to 600 kg and
up to 7 m long.
420 W
-
voltage used throughout
-
English – 2