Installation Warnings; Product Description And Intended Use; List Of Constituent Parts - Nice SO2000 Instructions Manual

– The manufacturer declines all liability for damages to
property, objects or people resulting from failure to
observe the assembly instructions. In such cases, the
warranty for material defects shall not apply.
– The weighted sound pressure level of the emission A is
lower than 70 dB(A).
– Cleaning and maintenance reserved for the user must
not be carried out by unsupervised children.
– Before intervening on the system (maintenance, clean-
ing), always disconnect the product from the mains
power supply and from any batteries.
– Inspect the system frequently, in particular the cables,
springs and supports to detect any imbalances and
signs of wear or damage. Do not use the product if it
needs to be repaired or adjusted, because defective
installation or incorrect balancing of the automation can
lead to injuries.
– The packing materials of the product must be disposed
of in compliance with local regulations.
– The product must not be installed outdoors.
– Keep an eye on moving doors and do not let anyone go
near them until they have opened or closed fully.
– Be careful when activating the manual unlocking device
(manual manoeuvre), as an open door may fall sudden-
ly due to weak or broken springs, or if it is unbalanced.
– Every month, check that the drive motor reverses when
the door encounters a 50 mm-high object placed on
the ground. If necessary, readjust the door and check it
again, as incorrect adjustment is potentially dangerous
(for drive motors incorporating a trapping safety system
that intervenes when the door's lower edge encounters
an obstacle).
– Motor with fixed power cable: the power cable cannot
be replaced. If the cable is damaged, the appliance
must be scrapped.
– Motor with removable power supply cable with ded-
icated connector: if the power supply cable is dam-
aged, it must be replaced by the manufacturer or by
the latter's technical assistance service, or nonetheless
by a similarly qualified person, so as to prevent any risk.

1.2 INSTALLATION WARNINGS

– Prior to installing the drive motor, check that the door
is in good working order, correctly balanced and that it
opens and closes properly.
– Prior to installing the drive motor, remove all unneces-
sary cables or chains and deactivate any equipment,
such as the locking devices,
– Check that there are no points where people could get
trapped or crushed against fixed parts when the door
is fully open or closed; if there are, arrange adequate
protective measures for these parts.
– Install the manoeuvre device for manual unlocking at
less than 1.8 m above the ground. NOTE - If removable,
the manoeuvre device must be kept next to the door
when removed.
– Make sure that the control elements are kept far from
moving parts but nonetheless directly within sight. Un-
less a selector is used, the control elements must be
installed at least 1.5 m above the ground and must not
be accessible.
– Permanently attach the trapping hazard warning labels
in a highly visible location or near the fixed control de-
vices (if present).
– Permanently attach the manual unlock (manual ma-
noeuvre) label close to the manoeuvring element.
– After installation, make sure that the motor prevents or
stops opening of the door when the latter is loaded with
a 20-kg weight secured to the centre of its bottom edge
(for drive motors that can be used with doors having
opening widths exceeding 50 mm).
– After installation, make sure that the mechanism is
properly adjusted and that the motor reverses when the
door collides with a 50 mm-tall object placed on the
ground (for drive motors incorporating a trapping safe-
ty system that intervenes when the bottom edge of the
door encounters an obstacle). Following installation,
check and ensure that no door parts obstruct public
roadways or pavements.
2
PRODUCT DESCRIPTION AND
INTENDED USE
SO2000 is an electromechanical actuator for automating sec-
2

PRODUCT DESCRIPTION AND INTENDED USE

tional doors up to 20 m2. Thanks to the cable outlet shaft, it
ensures easy connection with the spring support shaft of most
sectional doors available on the market.
The control unit supplied with the product, besides powering the
DC motor, ensures optimal adjustment of the gearmotor torque
and speed, precise measurement of the positions, gradual start-
ing and closing, and obstacle detection. It is also equipped with
a maintenance indicator to enable recording of the manoeuvres
performed by the gearmotor during its lifetime.
The unlocking mechanism, activated from the ground, disen-
gages the motor from the gearmotor body.
a
Any use of the product other than the intended use
described is not allowed!

2.1 LIST OF CONSTITUENT PARTS

"Figure 1" shows the main parts making up the Soon.
1
A
B
IBT4N
FUSE
LED
Close Open Sbs Stop Bluebus Flash
Close Open Sbs Stop Bluebus Flash
A Cover
Electronic control and command unit
B
C Gearmotor body
Locking/unlocking system
D
Transmission shaft housing
E
C D E
ENGLISH – 3