Installation Warnings; Product Description And Intended Use; List Of Constituent Parts - Nice RONDO Series Instructions And Warnings For Installation And Use

– Cleaning and maintenance reserved for the user must not
be carried out by unsupervised children.
– Before intervening on the system (maintenance, cleaning),
always disconnect the product from the mains power
supply and from any batteries.
– Inspect the system frequently, in particular the cables,
springs and supports to detect any imbalances and signs
of wear or damage. Do not use the product if it needs to
be repaired or adjusted, because defective installation or
incorrect balancing of the automation can lead to injuries.
– The packing materials of the product must be disposed of
in compliance with local regulations.
– The product must not be installed outdoors.
– Keep an eye on moving doors and do not let anyone go
near them until they have opened or closed fully.
– Be careful when activating the manual unlocking device
(manual manoeuvre), as an open door may fall suddenly
due to weak or broken springs, or if it is unbalanced.
– Every month, check that the drive motor reverses when
the door encounters a 50 mm-high object placed on the
ground. If necessary, readjust the door and check it again,
as incorrect adjustment is potentially dangerous (for drive
motors incorporating a trapping safety system that inter-
venes when the door's lower edge encounters an obsta-
cle).
– Motor with fixed power cable: the power cable cannot
be replaced. If the cable is damaged, the appliance must
be scrapped.
– Motor with removable power supply cable with dedicat-
ed connector: if the power supply cable is damaged, it
must be replaced by the manufacturer or by the latter's
technical assistance service, or nonetheless by a similarly
qualified person, so as to prevent any risk.

1.2 INSTALLATION WARNINGS

– Prior to installing the drive motor, check that the door is in
good working order, correctly balanced and that it opens
and closes properly.
– Prior to installing the drive motor, remove all unnecessary
cables or chains and deactivate any equipment, such as
the locking devices,
– Check that there are no points where people could get
trapped or crushed against fixed parts when the door is
fully open or closed; if there are, arrange adequate pro-
tective measures for these parts.
– Install the manoeuvre device for manual unlocking at less
than 1.8 m above the ground. NOTE - If removable, the
manoeuvre device must be kept next to the door when
removed.
– Make sure that the control elements are kept far from
moving parts but nonetheless directly within sight. Unless
a selector is used, the control elements must be installed
at least 1.5 m above the ground and must not be acces-
sible.
– Permanently attach the trapping hazard warning labels in
a highly visible location or near the fixed control devices
(if present).
– Permanently attach the manual unlock (manual manoeu-
vre) label close to the manoeuvring element.
– After installation, make sure that the motor prevents or
stops opening of the door when the latter is loaded with a
20-kg weight secured to the centre of its bottom edge (for
drive motors that can be used with doors having opening
widths exceeding 50 mm).
– After installation, make sure that the mechanism is prop-
erly adjusted and that the motor reverses when the door
collides with a 50 mm-tall object placed on the ground (for
drive motors incorporating a trapping safety system that
intervenes when the bottom edge of the door encounters
an obstacle). Following installation, check and ensure that
no door parts obstruct public roadways or pavements.
PRODUCT DESCRIPTION AND
2
INTENDED USE
2

PRODUCT DESCRIPTION AND INTENDED USE

RONDO is a gearmotor for spring-balanced rolling shutters. It
allows for automating shutters with a maximum height 6 m and
weight up to 170 kg.
The gearmotor can be mounted on shutters with spring support
shaft having a 42 mm, 48 mm or 60 mm diameter.
The spring support boxes can have a 200 mm or 220 mm diame-
ter. The two collars are made of die-cast aluminium.
It has a limit switch with micrometer screw and mechanical position
memory.
The unlocking device, operated from the ground, disengages the
motor from the gearmotor body and is only available for models
with electric brake.
a
Any use of the product other than the intended use
described is not allowed!

2.1 LIST OF CONSTITUENT PARTS

"Figure 1" shows the main parts making up the RONDO.
1
A
B
C
A
Half-collar
B Transmission shaft housing
C
Adaptor for collar
D Gearmotor body
E Limit switch position regulators
F Locking/unlocking system (where configured)
G Electric brake (where configured)
G
E
D
F
ENGLISH – 3