Mitsubishi Q Series User Manual page 10

3.5.31 Loop disconnection detection dead band
(buffer memory address 60, 92: Un\G60, Un\G92)........................................................................ 3-77
3.5.32 Unused channel setting (buffer memory address 61, 93: Un\G61, Un\G93)................................ 3-78
3.5.33 FeRAMs PID constant read command (buffer memory address 62, 94: Un\G62, Un\G94) ........ 3-78
3.5.34 Automatic backup setting after auto tuning of PID constants
(buffer memory address 63, 95: Un\G63, Un\G95)........................................................................ 3-79
3.5.35 Alert dead band setting (buffer memory address 164: Un\G164) ................................................. 3-79
3.5.36 Alert delay count (buffer memory address 165: Un\G165)............................................................ 3-79
3.5.37 Approach range setting (buffer memory address 167: Un\G167) ................................................. 3-80
3.5.38 Approach soak time setting (buffer memory address 168: Un\G168)........................................... 3-80
3.5.39 PID continuation flag (buffer memory address 169: Un\G169) ..................................................... 3-80
3.5.40 Cascade ON/OFF (buffer memory address 176: Un\G176).......................................................... 3-80
3.5.41 Cascade gain (buffer memory address 177: Un\G177)................................................................. 3-81
3.5.42 Cascade bias (buffer memory address 178: Un\G178) ................................................................. 3-81
3.5.43 Cascade monitor (buffer memory address 179: Un\G179) ........................................................... 3-81
3.5.44 Mode setting of Alert 1 to 4 (buffer memory address 192 to 195, 208 to 211:
Un\G192 to Un\G195, Un\G208 to Un\G211) ................................................................................ 3-82
3.5.45 Scaling value (buffer memory address 196, 212: Un\G196, Un\G212) ........................................ 3-82
3.5.46 Scaling range upper limit • lower limit
(buffer memory address 197, 198, 213, 214: Un\G197, Un\G198, Un\G213, Un\G214) ............. 3-83
3.5.47 Scaling width upper limit • lower limit
(buffer memory address 199, 200, 215, 216: Un\G199, Un\G200, Un\G215, Un\G216) ............. 3-83
3.5.48 Hold command (buffer memory address 201, 217: Un\G201, Un\G217) ..................................... 3-84
3.5.49 Command advancing (buffer memory address 202, 218: Un\G202, Un\G218) ........................... 3-85
3.5.50 Segment monitor (buffer memory address 256, 512: Un\G256, Un\G512) .................................. 3-85
3.5.51 Segment remaining time (buffer memory address 257, 513: Un\G257, Un\G513) ...................... 3-85
3.5.52 Execution times monitor (buffer memory address 258, 514: Un\G258, Un\G514)....................... 3-86
3.5.53 Pattern end output flag (buffer memory address 259, 515: Un\G259, Un\G515)......................... 3-86
3.5.54 End status flag (buffer memory address 260, 516: Un\G260, Un\G516)...................................... 3-86
3.5.55 Wait status flag (buffer memory address 261, 517: Un\G261, Un\G517) ..................................... 3-86
3.5.56 Hold status flag (buffer memory address 262, 518: Un\G262, Un\G518)..................................... 3-86
3.5.57 Advancing completion flag (buffer memory address 263, 519: Un\G263, Un\G519) ................... 3-86
3.5.58 Execution pattern monitor (buffer memory address 264, 520: Un\G264, Un\G520) .................... 3-87
3.5.59 Zone PID monitor (buffer memory address 265, 521: Un\G265, Un\G521) ................................. 3-87
3.5.60 Execution pattern (buffer memory address 272, 528: Un\G272, Un\G528) ................................. 3-87
3.5.61 Start mode (buffer memory address 273, 529: Un\G273, Un\G529) ............................................ 3-88
3.5.62 Time scale (buffer memory address 274, 530: Un\G274, Un\G530) ............................................ 3-89
3.5.63 Zone setting (buffer memory address 275 to 313, 531 to 569:
Un\G275 to Un\G313, Un\G531 to Un\G569) ................................................................................ 3-89
3.5.64 Program pattern (buffer memory address 320 to 500, 576 to 756:
Un\G320 to Un\G500, Un\G576 to Un\G756) ................................................................................ 3-91
4 SETUP AND PROCEDURE BEFORE STARTING THE OPERATION
4.1 Handling Precautions............................................................................................................................... 4- 1
4.2 Procedure before Starting the Operation ................................................................................................ 4- 2
4.3 Parts Identification.................................................................................................................................... 4- 3
A - 8
4- 1 to 4- 9
A - 8