Toro Greensmaster eTriFlex 3360 Operator's Manual page 25

Backlap Reel Speed Options (cont'd.)
6
7
8
9
Note:
The factory default setting is 200 rpm
(increment number 1).
Adjusting the Clip-Control Feature
Understanding the Radius-Dependent-Speed
(RDS) System
To achieve a consistent, high quality-of-cut and a
uniform after cut appearance, the machine is equipped
with the patent-pending Radius Dependent Speed™
(RDS) system. The RDS system is a clip-control
and independent wheel-speed feature that varies the
speeds of each reel motor and each traction motor to
maintain a constant clip and reduce turf scrubbing in
turns while cutting.
When the machine is turning while cutting (e.g., during
the clean-up pass), the reel on the inside of the turn
will rotate at a slower rpm than the reel on the outside
of the turn. The center reel splits the difference of the
inside and outside reel speeds so that all three cutting
units have the same clip. The sharper the turn, the
greater the difference in reel speeds. Additionally, if
the machine speed changes while you are cutting,
the RDS system adjusts the reel speed to maintain a
constant clip. This feature reduces turf thinning on
the inside reel (in comparison to other riding greens
mowers), which virtually eliminates triplex ring.
The RDS system also adjusts each wheel-motor
speed during a turn, similar to the reel-motor speeds
changing in a turn. The inside wheel motor will turn
at a slower rpm than the outside wheel motor. This
minimizes wheel scrubbing in the turn and can reduce
triplex ring.
Setting the Clip-Control Feature
Navigate to the C C
LIP
system feature.
•
Clip control set to ON: The machine uses your
settings from the H
EIGHT OF
C options and the left and right wheel speeds
OUNT
to determine the speed of each reel.
•
Clip control set to O
setting from the R
EEL
Note:
The factory default setting is ON.
400
440
480
520
option to set the RDS
ONTROL
C (HOC) and B
UT
: The machine uses your
FF
S option.
PEED
Adjusting the Height of Cut (HOC)
Navigate to the H
the height of cut. The clip control feature must be
set to O to use this feature; refer to
N
Clip-Control Feature (page
Note:
The factory default setting is 3.2 mm (0.125
inch).
Adjusting the Number of
Cutting-Unit Blades
Navigate to the B
number of cutting-unit blades. Determine the number
of blades in your equipped cutting units, and select
the appropriate value (5, 8, 11, or 14).
Note:
The factory default setting is 11.
Adjusting the Maximum Mowing
Speed
Navigate to the M
maximum mowing speed. You can adjust the speed
from 4.8 km/h (3.0 mph) to 8.0 km/h (5.0 mph) in
increments of 0.3 km/h (0.2 mph).
Note:
The factory default setting is 6.1 km/h (3.8
mph).
Adjusting the Maximum Transport
Speed
Navigate to the M
maximum transport speed. You can adjust the speed
from 8.0 km/h (5.0 mph) to 16.0 km/h (10.0 mph) in
increments of 0.8 km/h (0.5 mph).
Note:
The factory default setting is 16.0 km/h (10.0
mph).
Adjusting the Maximum Reverse
Speed
Navigate to the M
maximum reverse speed. You can adjust the speed
from 3.2 km/h (2.0 mph) to 4.8 km/h (3.0 mph) in
increments of 0.8 km/h (0.5 mph).
Note:
The factory default setting is 4.0 km/h (2.5
LADE
mph).
Setting the Slow in Turn Function
Navigate to the S
in turn function. The slow in turn function decreases
25
C (HOC) option to adjust
EIGHT OF UT
Setting the
25).
C option to adjust the
LADE OUNT
M option to adjust the
AX OW
T option to adjust the
AX RANSPORT
R option to adjust the
AX EVERSE
& T option to set the slow
LOW URN