Samsung CLX-8385NX Series User Manual page 118

Message Meaning
The toner cartridge
[xxx] toner
you have installed is
cartridge is not
not for your
compatible. Check
machine.
userís guide
The toner cartridge
[xxx] toner
is not installed or the
cartridge is not
CRUM (Consumer
installed. Install it
Replaceable Unit
Monitor) in the
cartridge is not
properly connected.
DC motor does not
There is a problem
operate: [zzz]. in the control of DC
Please turn off motor unit.
then on
Did not supply
Not supplied toner to
enough [xxx] the imaging unit.
toner. Remove
seal tape &
reinstall
The machine
Did not supply
received several
enough [xxx]
papers with many
toner. Please
images, and it
open/close door
cannot supply the
toner properly.
The imaging unit has
End of life,
reached its life span.
Replace with new
[xxx] imaging unit
A toner cartridge has
End of life,
reached its estimated
Replace with new
cartridge life. The
[xxx] toner
printer stops printing.
cartridge
Fax memory is There is no more
almost full. Print
available fax
or remove memory. No more
received fax Job
fax data can be
received.
Fax memory is full. Available fax
Print or remove memory is now
received fax Job 1MB.
Suggested solutions
Install a Samsung-
genuine toner
cartridge, designed
for your machine.
Try to reinstall the
toner cartridge.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
• Remove the
sealing tape from
the imaging unit.
• Thoroughly roll the
toner cartridge five
or six times, and
reinstall it.
• Turn the machine
off and turn it on
again.
Check the toner
cartridge and
redistribute the toner.
(Page 11.3) If the
problem still persists,
please call for
service.
Replace the imaging
unit.
Replace the toner
cartridge with a
Samsung-genuine
toner cartridge.
(Page 11.4)
Delete the received
fax data in the
memory. Call for
service to delete fax
memory.
Delete the received
fax data in the
memory to secure
memory. Call for
service.
12.12
Message Meaning
The finisher cover is
Finisher door is
not securely latched.
open. Close it
Finisher error:
There is a problem
[zzz]. Please turn in the finisher unit.
off then on
Fuser error: [zzz].
There is a problem
Please turn off in the fuser unit
then on working.
Fuser unit is not
The fuser unit is not
installed correctly.
installed or correctly.
Install it
LSU error: [zzz].
There is a problem
Please turn off in the control of LSU
then on
unit.
Motor does not
There is a problem
operate: [zzz]. in the control of
Please turn off motor unit.
then on
Original paper
The lead edge of the
does not feed in document failed to
scanner actuate the scan
sensor within the
correct time after
actuating the
registration sensor.
Original paper is
Oversized document
too long for or double-feeding of
scanner. Check
originals.
size
Original paper jam The originals are
in front of scanner jammed in DADF.
<Troubleshooting>
Suggested solutions
Close the finisher
until it locks into
place.
Turn the machine off
and reinstall the
finisher again. Check
that the finisher cable
is connected
properly. If the
problem persists,
please call for
service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
Install the fuser unit.
Call for service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
Open the DADF
cover and remove
jammed original.
(Page 12.1)
Open the DADF
cover and remove the
jammed original.
(Page 12.1)
Check the document
size whether it is
supported.
(Page 15.1)
Open the DADF
cover and remove the
jammed original.
(Page 12.1)