TDK-Lambda GENESYS GEN 2400W Series Technical Manual page 8

3.7.3 AC Input Wire Connection ............................................................................................................ 24
3.8 TURN-ON CHECKOUT PROCEDURE ................................................................................................. 25
3.8.1 General ......................................................................................................................................... 25
3.8.2 Prior to Operation .......................................................................................................................... 25
3.8.3 Constant-Voltage Check ............................................................................................................... 26
3.8.4 Constant-Current Check ............................................................................................................... 26
3.8.5 OVP Check ................................................................................................................................... 26
3.8.6 UVL Check .................................................................................................................................... 26
3.8.7 Foldback Check ............................................................................................................................ 27
3.8.8 Address Setting ............................................................................................................................. 27
3.8.9 Baud Rate Setting (RS-232 and RS-485 only) ............................................................................. 27
3.9 CONNECTING THE LOAD ................................................................................................................... 27
3.9.1 Load Wiring ................................................................................................................................... 27
3.9.2 Current Carrying Capacity ............................................................................................................ 27
3.9.3 Wire Termination ........................................................................................................................... 28
3.9.4 Noise and Impedance Effects ....................................................................................................... 28
3.9.5 Inductive Loads ............................................................................................................................. 29
3.9.6 Making the Load Connections ...................................................................................................... 29
3.9.7 Connecting Single Loads, Local Sensing (default configuration). ................................................ 32
3.9.8 Connecting Single Loads, Remote Sensing ................................................................................. 32
3.9.9 Connecting Multiple Loads, Radial Distribution Method ............................................................... 32
3.9.10 Multiple Load Connection with Distribution Terminals ................................................................ 33
3.9.11 Grounding Outputs...................................................................................................................... 33
3.10 LOCAL AND REMOTE SENSING ....................................................................................................... 34
3.10.1 Sense Wiring ............................................................................................................................... 34
3.10.2 Local Sensing ............................................................................................................................. 34
3.10.3 Remote Sensing ......................................................................................................................... 35
3.10.4 J2 Sense Connector Technical Information ................................................................................ 35
3.11 REPACKAGING FOR SHIPMENT ...................................................................................................... 35
CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS ........................................ 36
4.1 INTRODUCTION ................................................................................................................................... 36
4.2 FRONT PANEL CONTROLS AND INDICATORS ................................................................................. 36
4.3 REAR PANEL ........................................................................................................................................ 38
4.3.1 Auxiliary Power Supply ................................................................................................................. 39
4.4 REAR PANEL SW1 SETUP SWITCH ................................................................................................... 39
4.4.1 SW1 DIP-Switch Position Function ............................................................................................... 40
4.4.2 Resetting the SW1 DIP-switch ...................................................................................................... 40
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR ............................................. 41
4.5.1 Making J1 connections ................................................................................................................. 41
CHAPTER 5 LOCAL OPERATION ............................................................................................................ 43
5.1 INTRODUCTION ................................................................................................................................... 43
5.2 STANDARD OPERATION..................................................................................................................... 43
5.2.1 Constant-Voltage Mode ................................................................................................................ 43
5.2.2 Constant-Current Mode ................................................................................................................ 43
5.2.3 Automatic Crossover..................................................................................................................... 44
5.3 OVER-VOLTAGE PROTECTION (OVP) ............................................................................................... 44
5.3.1 Setting the OVP level .................................................................................................................... 44
5.3.2 Activated OVP protection indications ............................................................................................ 44
5.3.3 Resetting the OVP circuit .............................................................................................................. 44
5.4 UNDER VOLTAGE LIMIT (UVL) ........................................................................................................... 44
5.4.1 Setting the Output UVL level ........................................................................................................ 44
5.5 FOLDBACK PROTECTION................................................................................................................... 45
5.5.1 Setting the FOLDback Protection ................................................................................................. 45
5.5.2 Resetting Activated Foldback Protection ...................................................................................... 45
5.6 OUTPUT ON/OFF CONTROL ............................................................................................................... 45
5.7 OUTPUT SHUT-OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR ....................................... 45
5.8 ENABLE/DISABLE CONTROL VIA REAR PANEL J1 CONNECTOR .................................................. 46
83-517-000 Rev.A