Download
Share
Print this page
Yardistry YM11909 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Yardistry Manuals
  4. Lawn and Garden Equipment
  5. YM11909
  6. Installation and operating instructions manual

Yardistry YM11909 Installation And Operating Instructions Manual

Pavilion
Hide thumbs

Advertisement

Quick Links

Download this manual
10' x 10' PAVILION
Installation and Operating Instructions – YM11909
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Revised 08-24-2020
10'
120
(3.04 m)
Yardistry – North America
119
9' 11"
(3.02 m)
Toll Free Customer Support:
1.888.509.4382
info@yardistrystructures.com
www.yardistrystructures.com
Height: 9' 3-1/2" (2.83 m)
Y40000-909

Advertisement

loading

Related Manuals for Yardistry YM11909

Summary of Contents for Yardistry YM11909

  • Page 1 10’ x 10’ PAVILION Installation and Operating Instructions – YM11909 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY Revised 08-24-2020 10’ (3.04 m) Yardistry – North America 9’ 11” (3.02 m) Toll Free Customer Support: 1.888.509.4382 info@yardistrystructures.com www.yardistrystructures.com Height: 9’ 3-1/2” (2.83 m)

  • Page 2: Important Safety Notice

    Wood is NOT flame retardant and will burn. Grills, fire pits and chimineas are a fire hazard if placed too close to a Yardistry structure. Consult user’s manual of the grill, fire pit or chimnea for safe distances from combustible materials.
  • Page 3 Limited Warranty Yardistry warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. In addition, for any product with lumber, all lumber is warranted for five (5) years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable.

  • Page 4: Instructions For Proper Maintenance

    Instructions for Proper Maintenance Your Yardistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it.

  • Page 5: Assembly Tips

    Assembly Tips Following are some helpful tips to make the assembly process smooth and efficient. PRE-ASSEMBLIES: (i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc) • Work on a raised, solid and flat surface such as, a table or saw horse. •...
  • Page 6 Permanent Installation Examples Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Pavilion. We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure to a pre-existing or new wood or concrete surface.
  • Page 7 Permanent Installation Examples cont. Concrete Patio [min. 10’ 1” x 10’ 6-1/2” (3.073 m x 3.213 m)] with 6” (15.24 cm) clearance on all sides Anchoring Hardware not included Wood Deck [min. 10’ 1” x 10’ 6-1/2” (3.073 m x 3.213 m)] with 6”...

  • Page 8: Part Identification

    Part Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 4pc. (752) - Post 2235.2mm ( 88") Y70131-752 4pc. (842) - Gusset Right 876.3mm (34-1/2") 4pc.

  • Page 9: Hardware Identification

    Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 1/4" x 1-15/16" 24pc. Lag Screw No.12 Shank (Y06218-219) 4pc. Lag Screw (1/4" Shank) 5/16 x 3" (Y06218-330) 4pc.
  • Page 10 Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. #10 x 1-1/4" 90pc. Pan Screw (Y06491-711) 18pc. - 1/4" Lock Nut #10 x 2-1/2" 8pc.
  • Page 11 Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 2pc. 4pc. Ridge Cap Short 2pc. Ridge Clip 15 (Y01033-278) (Y01033-276) Roof Edge Left Y01033-274 (Y01033-152) Main Panel 4pc.
  • Page 12 • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department. PRODUCT NUMBER: YM11909 CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 1) CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 2) CARTON I.D.
  • Page 13 Step 2: Post Assemblies A: At the bottom of each (752) Post insert two 5/16” T-Nuts as shown in F2.1 and F2.2. B: At the bottom of each (752) Post place two Post Mounts tight to the bottom and inside faces as shown in F2.1 and F2.2.
  • Page 14 Step 3: Gable Beam Assembly A: Place two (833) Gable Beams tight together, then place one (846) Gable Upright Assembly centred, on one side of (833) Gable Beams and one (832) Gable Inside on the other side. (832) Gable Inside to be flush to top of (833) Gable Beams.
  • Page 15 Step 4: Side Beam Assembly Part 1 A: Fit two (836) Side Beam Outsides together so the middle pilot holes are at the bottom for both. Connect using two 5/16 x 1-1/4” Hex Bolts (with 5/16” lock washer, 1/4-5/16” large washer and 5/16” t-nut) as shown in F4.1. B: Connect one (835) Side Beam Ends to each end of one (834) Side Inside Beam using two 5/16 x 1-1/4”...
  • Page 16 Step 4: Side Beam Assembly Part 2 D: Place one Outside Beam Assembly and one Inside Beam Assembly together so the ends are flush. Match the bolt holes in each assembly. Attach assemblies with 16 #8 x 2-1/4” Wood Screws. (F4.3) E: Repeat Step D one more time to make a second Side Beam Assembly.
  • Page 17 Step 5: Frame Assembly and Anchoring Part 1 A: Move your Post Assemblies to the final location. Make sure the ground is flat and level before continuing assembly. B: With one person at each Post stand two complete Post Assemblies. A third person places one Side Beam Assembly against the outside of each Post, flush to the tops and outside corners.
  • Page 18 Step 5: Frame Assembly and Anchoring Part 2 E: Make sure each corner is square and level then attach Side Beam Assembly to Post Assemblies with one 5/16 x 4-3/4” Lag Screw (with 1/4-5/16” large washer) per corner and Gable Beam Assembly to Post Assemblies with one 5/16 x 3”...
  • Page 19 Step 6: Attach Gussets Note: The bevelled ends on each F6.1 Gable Beam (843) (842) Gusset gusset should always face away from Assembly Gusset Right (843) the wood it is attaching to. Left Gusset Side Beam Left Assembly A: Make sure the assembly is still square (842) and level then facing one Side Beam Gusset...
  • Page 20 Avery Inst 6A - Frame Roof Panel Step 7: Roof Panel Frame Part 1 A: Lay out three (831) Rafters on a hard flat surface as shown in F7.1. You will need lots of room for this step. Avery Inst 6A - Frame Roof Panel B: Place 1 (839) Strap Short on the bottom of three (831) Rafters, flush to the outside edge of the first and centred on the last.
  • Page 21 Step 7: Roof Panel Frame Part 2 Avery Inst 6A - Frame Roof Panel D: Lay out three more (831) Rafters beside the first three, then tight to each (839) Strap Short place one (840) Strap Long and tight to the first (840) Strap Long place one (839) Strap Short. Make sure the wider gap on each strap is on the outside.
  • Page 22 Step 7: Roof Panel Frame Part 3 F: Make sure frame is square. Measurements to be as shown in F7.6. G: In the centre middle gap between (831) Rafters place one (838) Rafter Brace flush to the top of each (837) Rafter Top.

  • Page 23: Handle With Care

    STOP STOP STOP STOP INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! HANDLE WITH CARE! Place roofing material on a non-abrasive surface before assembly as it can bend, dent and scratch easily. WARNING – DO NOT OVER TIGHTEN ROOFING SCREWS! Over tightening screws will cause roofing material to crush.
  • Page 24 STOP STOP STOP STOP INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! BE SURE TO REMOVE ALL PLASTIC COVERING, ON BOTH SIDES OF THE ALUMINUM PANELS AND TRIM, DIRECTLY BEFORE INSTALLING EACH PIECE. (One side is clear and the other is blue, both must be removed.) Example #1 Example #2 Overtightened and Crushed...
  • Page 25 Step 8: Attach Roof Panels Part 1 Note: Be sure to remove all plastic covering on both sides of the metal panels directly before installing each piece. A: Make sure panel is still square then on one Roof Panel Frame place one Side Panel flush to the top and sides of the outside (831) Rafter on the side shown below.
  • Page 26 Step 8: Attach Roof Panels Part 2 E: Place one Roof Edge Left and one Roof Edge Right on the bottom of one Roof Panel Frame so they meet tight and the ends are flush with the outside ends of (839) Strap Short and (840) Strap Long. Predrill the end holes on both Roof Edge Right and Roof Edge Left with a 1/8”...
  • Page 27 Step 8: Attach Roof Panels Part 3 F: Attach the Main Panels and Side Panels to Roof Panel Frame using 39 #8 x 1” Hex Roofing Screws as shown in F8.5. Be sure not to overtighten screws. F8.5 #8 x 1” Hex Roofing Screws (39 per Panel Frame) Y01033-273 - Side Panel x 4 R0-Roo ng Scr.
  • Page 28 Step 8: Attach Roof Panels S39 -Wood Screw #7 x 3/4 x 13 Part 4 Y010XX-278 - Ridge Cap Short 16.7 Y010XX-277 - Ridge Cap 88 G: Place Weather Seal on the inside of two Ridge Clip 15 then place one Ridge Clip 15 flush to each side of Roof Panel Frame and 2-3/4”...
  • Page 29 Step 9: Attach Roof Panels to Frame Part 1 A: With four assemblers lift one Roof Panel Frame up and over Post and Beam Frame Assembly so the notches in (831) Rafters rest on Side Beam Assembly and (837) Rafter Tops are flush to the outside of each (846) Gable Upright Assembly.
  • Page 30 Step 9: Attach Roof Panels to Frame Part 2 C: From inside the assembly attach the two Roof Panel Frames together through (838) Rafter Brace with two 1/4 x 4-3/4” Hex Bolts (with two 1/4-5/16” large washer and one 1/4” lock nut) and through (837) Rafter Tops with eight 1/4 x 2-3/4”...
  • Page 31 Step 9: Attach Roof Panels to Frame Part 3 D: Loosely attach each of the centre (831) Rafters to the inside of each Side Beam Assembly with one Rafter Beam Bracket per (831) Rafter using one 1/4 x 2” Hex Bolt (with two 1/4-5/16” large washer and one 1/4” lock nut) per bracket.
  • Page 32 Step 10: Attach Ridge Caps Part 1 A: Slide Ridge Cap over the Ridge Clips towards the centre of the roof. (F10.1 and F10.2) B: With the swaged end facing in slide one Ridge Cap Short at each end of the roof over the Ridge Clips. Use the swaged end to help push the Ridge Cap to the centre of the roof.
  • Page 33 Step 10: Attach Ridge Caps Part 2 C: Make sure the Ridge Cap Shorts are flush to the outside edge of the roof then attach each end of the Ridge Cap to each Ridge Cap Short with two #8 x 3/4” Sheet Metal Screws per side. (F10.5, F10.6 and F10.7) F10.5 F10.6 Ridge...
  • Page 34 Step 11: Attach Gable Ends A: On one side of the assembly place two (830) Fascia against the outside (831) Rafters so the peaks meet in the centre and they are tight and flush to the top and edge of (846) Gable Upright Assembly. Bottom of (830) Fascia to bottom of (831) Rafter should measure 1”...
  • Page 35 Step 12: Attach Gable Gussets A: From inside the assembly place one (847) Gable Gusset tight to each side of (846) Gable Upright Assembly so it is resting on (830) Fascia, tight and flush to (831) Rafter. (F12.1 and F12.2) B: Attach each (847) Gable Gusset to (830) Fascia with two #8 x 2”...
  • Page 36 Step 13: Truss Assemblies Part 1 A: Attach one Tie Wrap Bracket to each end of one (841) Tie with one #10 x 1-1/4” Pan Screw per bracket using the inside holes. (841) Tie is tight to end of bracket. Repeat to complete 3 more times. (F13.1) F13.1 Tie Wrap Bracket...
  • Page 37 Step 13: Truss Assemblies Part 2 B: With a helper place (841) Ties with brackets tight against (831) Rafters. Make sure (841) Ties are level then attach Tie Wrap Brackets to (831) Rafters with two #10 x 1-1/4” Pan Screws on both sides of each bracket. (F13.2, F13.3, F13.4 and F13.5) Y50000-841- Tie C: Pre-drill with a 1/8”...
  • Page 38 Step 14: Attach Plaque A: Attach Yardistry Plaque to a prominent location on your Pavilion with two #10 x 1-1/4” Pan Screws. This provides warnings concerning safety and important contact information. A tracking number is provided to allow you to get critical information or order replacement parts for this specific model. (F14.1 and F14.2) F14.1...
  • Page 39 NOTES support@yardistrystructures.com...
  • Page 40 Atención a: Servicio de Atención al Cliente À l’attention de: Service à la clientèle Yardistry would like to say “Thank you” for your time and feedback. Yardistry quiere “Agradecerle” por su tiempo y su opinión. Yardistry aimerait vous remercier d’avoir pris le temps de répondre au sondage.