Related Manuals for Yardistry G005
Summary of Contents for Yardistry G005
- Page 1 Installation Manual -G005 Corner Feature YM11562 63 ½” (1.61m) (1m) (1m) (1.18m) (1.18m) Yardistry Ltd. Mount Forest, ON Canada N0G 2L1 Toll Free Customer Support: 1.888.509.4382 info@yardistrystructures.com www.yardistrystructures.com Revised 08/24/2011...
-
Page 2: Important Safety Notice
Tools Required Warranty: Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer’s installation instructions. • Tape Measure •... -
Page 3: Material List
Material List Top and Bottom Rail and 2x 3’ 3 1/2” (1m) 2’ 2 3/4” (67.9cm) #8 x 2 1/4” Wood Screw #10 x 1” Pan Head Screw #8 x 1 1/2” Wood Screw (3) Post Caps (12) Panel Clips (2)Arch Topper (2) One High X Topper (4) Two High X Panel... - Page 4 Insert male into female. Slide down until flush with required. adjacent panel. Step 1- Assemble Panels Introduzca el extremo macho en el extremo hembra. res et les panneaux dans l'orientation exigée pour votre projet. Deslícelo hacia abajo hasta que quede al ras del 1. R emove the upper metal connectors on both sides of PX2 - Two High X Panel. Reattach the metal connectors panel adyacente.
- Page 5 Step 2- Assemble Panels Continued 4. R emove the upper metal connectors on both sides of PX2 - Two High X Panel. Reattach the metal connectors to PX2 by securing the bottom two holes of the metal connectors to the top two holes on PX2 so that the metal connectors stick out from the top. Slide PX1 - One High X Topper between the two protruding metal connectors on the top of PX2. Attach the metal connectors to the factory drilled holes in PA1. (Fig. 4A) *Ensure Panels are oriented correcly! (Fig. 4B) 5. S ecure panels with a S4 - 2 1/4” Wood Screw the location indicated by the large...
- Page 6 Step 3- Assemble Side Wall 1. Assemble panels together in Fig. 1 configuration shown. (Fig.1) Insert male connector into female. Slide down until flush with adjacent panel as shown. (Fig. 1A) Instructions de base Cut and attach Top and Bottom Pautas básicas para Instruc Assemble Toppers to Panels. Pautas básicas para pour l'assemblage pour l'...
- Page 7 Step 4- Attach Panel Clips For Wings 1. O n a flat surface place P- 4x4 Post on its side and position Panel Clips in Fig. 2 locations indicated in Figures 1 and 1A. Ensure Panel Clips are oriented as shown in Diagrams! 2. Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3/8” or 3.49cm away from the side of the post as shown in Fig. 2. 1 3/8”...
- Page 8 Step 5- Attaching Post Caps 1. Place a Post Cap on each 4x4 Post 2. S ecure Post Cap with 2 S7- #8- 1 1/2” Wood Screws 3x Post Caps #8- 1 1/2” Wood Screws...
- Page 9 This identifies information that requires special Check that set or assembly is properly level Step 6- Attach Wings to Posts attention. Improper assembly could lead to an before proceeding. unsafe or dangerous condition. Pre-drill 1/8” & 3/16” Bit Where this is shown, 2 or 3 Help Help 1. P lace panel assemblies on posts as shown (Fig.1) allowing a 2” gap between...
Need help?
Do you have a question about the G005 and is the answer not in the manual?
Questions and answers