Table Of Contents - IBM 1800 Operating Procedures Manual

Contents
THE ROLE OF THE OPERATOR
Clearing a Parity Check Condition 49
THE PROGRAM AND RUN BOOK Clearing a Forms Check Condition 49
OPERA TOR RESPONSIBILITIES
IBM 1627 PLOTTER
52
INTRODUCTION
2
Operator Controls, Left Panel . 52
Input/Output Control
2
Operator Controls, Right Panel 53
DATA CHANNEL CONTROL 2
Installing a Roll of Graph Paper
53
DIRECT PROGRAM CONTROL .
3
Installing a Sheet of Graph Paper 54
INPUT/OUTPUT INTERRUPTS. 3
Assembling the Pen . 55
Checking Plotter Operation 55
IBM 1801/1802 PROCESSOR-CONTROLLER . 6
Program Checkout Routine 56
Processor-C on troller Console 6
Pushbutton Switches and Lights, Top Row 8
IBM 1816 PRINTER-KEYBOARD AND IBM 1053 PRINTER 58
Pushbutton Switches, Bottom Row 9
PRINTER 58
Rotary Switches
10
KEYBOARD 58
Toggle Switches
11
Operator Controls, Keyboard 58
Status Indicators
11
Operator Controls, 1053 Printer 59
Data Flow Indicators
12
Manual Controls, Printer
60
Main Storage Display (Single Instruction Operations)
13
Print Element and Ribbon Controls
-
61
Main Storage Display (Single Cycle Operations) . 13
Inserting Forms . 61
Main Storage Load 13
Changing the Ribbon 62
Changing the Print Element 63
IBM 1054 PAPER TAPE READER 16
Setting Margins . 64
PAPER TAPE INITIAL PROGRAM LOAD .
16
Clearing a Not Ready Condition 64
Operator Controls 16
Clearing an Overprint Condition 64
Identifying Start of Tape 17
Clearing Double Key Errors 64
Loading Punched Tape . 17
Example of Keyboard Operation 64
Loading a Tape Loop
18
IBM 1810 DISK STORAGE 66
Splicing Paper Tape. 19
Operator Controls 66
Clearing Error Conditions 19
Removing a Disk Cartridge.
67
IBM 1055 PAPER TAPE PUNCH. 22
Inserting a Disk Cartridge 68
Operator Controls 22
Clearing a Write Select Error Condition 68
Loading Blank Tape 23
Disk Cartridge Handling 68
Removing Punched Tape
24
IBM 2841 STORAGE CONTROL AND 2311 DISK
Emptying the Chad Box 24
STORAGE DRIVE . 70
Clearing a Not Ready Condition
25
2841 STORAGE CONTROL 70
2311 DISK STORAGE DRIVE 70
IBM 1442 CARD READ PUNCH. 28
Operator Controls, 2841 70
CARD READING 28
Operator Controls, 2311
71
CARD PUNCHING . 28
Removing a Disk Pack 72
CARD FEED. 28
Loading a Disk Pack 73
INITIAL PROGRAM LOAD 28
Disk Pack Handling. 74
Operator Controls 29
Readying the 1442 .
30
IBM 2401 MAGNETIC TAPE UNIT 76
Initiating Last Card Sequence 30
WRITING AND READING MAGNETIC TAPE.
76
Clearing Card Jams . 31
FILE PROTECTION DEVICE
76
Clearing Error Conditions
32
Operator Controls 77
Operating the Power Window 78
IBM 1443 PRINTER
38 Loading Magnetic Tape. 79
CARRIAGE.
38
Unloading Magnetic Tape
80
Operator Controls
39
Placing Tape Markers on Magnetic Tape 80
Manual Controls, Left Side 40
Cleaning the Tape Transport 81
Manual Controls, Front 41
Magnetic Tape Handling 82
Manual Controls, Right Side
42
APPENDIX A.
CARRIAGE CONTROL TAPE 83
Inserting a Control Tape 42
Inserting Forms .
43
Marking a Tape for Punching (Six Lines Per Inch)
84
Switching the Six-to-Eight Line Drive
45
Marking a Tape for Punching (Eight Lines Per Inch) 85
Removing or Inserting a Typebar 46
Punching a Tape.
85
Replacing a Ribbon.
48
APPENDIX B. SAFETY.
87
Clearing a Sync Check Condition 49
INDEX
88
Contents
iii