DigiDesign D-Control Manual page 124

Press the encoder Select switch to move down to the indi-
3
vidual plug-in level.
Turn the encoder knob to select the plug-in whose auxiliary
4
output you want to select.
Press the encoder Select switch to move down to the list of
5
plug-in auxiliary outputs.
Do one of the following:
6
• Press the flashing encoder Select switch or press the flash-
ing Assign Inputs switch to confirm the assignment.
– or –
• Press the flashing Escape switch to cancel the assign-
ment.
Assigning Inserts and Sends Directly from a
Channel
You can assign Inserts or Sends directly to individual channels
without entering global Assign mode.
To assign an individual insert or send:
On the channel where you want to make the assignment,
1
press the Inserts or Sends switch to display the corresponding
elements on the channel's encoders.
Press the Select switch on the encoder where you want to
2
make the assignment. The encoder scribble strip shows a right
arrow ("> – –") to indicate the encoder is in Assign mode.
Turn the corresponding encoder knob to select from the first
3
level of menu choices.
Press the encoder Select switch to move down and the By-
4
pass/Mute/Pre switch to move up through menu levels.
Do one of the following:
5
• Press the flashing encoder Select switch to confirm the as-
signment.
– or –
• Press the flashing Escape switch to cancel the assign-
ment.
To change a previously assigned insert or send:
On the channel where you want to change the assignment,
1
press the Inserts or Sends switch to display the corresponding
elements on the channel's encoders.
Press and hold the encoder Select switch for the insert or
2
send you want to change, until the encoder scribble strip
shows a right arrow (">") next to the assignment to indicate
the encoder is in Assign mode.
Do one of the following to select a new insert or send:
3
• Turn the corresponding encoder knob to select from the
current level of menu choices.
– or –
116 D-Control Guide
• Press the encoder Select switch to move down and the
Bypass/Mute/Pre switch to move up through menu lev-
els.
When the new insert or send is displayed in the encoder
4
scribble strip, do one of the following:
• Press the flashing encoder Select switch to confirm the as-
signment.
– or –
• Press the flashing Escape switch to cancel the assign-
ment.
To remove an individual insert or send:
On the channel where you want to remove the assignment,
1
press the Inserts or Sends switch to display the corresponding
elements on the channel's encoders.
Press and hold the encoder Select switch for the insert or
2
send you want to remove, until the encoder scribble strip
shows a right arrow (">") next to the assignment to indicate
the encoder is in assign mode.
Press the encoder Bypass/Mute/Pre switch repeatedly until
3
you reach the top level menu for the assignment.
Turn the encoder knob counter-clockwise until no assign-
4
ment is visible.
Do one of the following:
5
• Press the flashing encoder Select switch to confirm the re-
moval.
– or –
• Press the flashing Escape switch to cancel the removal
and restore the assignment.
Making Elements Active or Inactive
You can make Inputs, Outputs, Inserts, Sends, and entire
tracks active or inactive directly from D-Control by entering a
temporary Make Inactive mode.
To toggle an input, output, send, or plug-in active/inactive:
Make sure the channel is showing the top-level view for the
1
element you want to make active/inactive.
Press a Make Inactive switch to enter the appropriate Make
2
Inactive mode.
Press the Bypass/Mute/Pre switches on encoders to deacti-
3
vate or reactivate their corresponding track elements.
Press the flashing Make Inactive switch to exit Inactive
4
mode.
To toggle a track inactive/active:
Press any of the Make Inactive switches.
1
Press channel strip Select buttons to deactivate or reactivate
2
the corresponding tracks.