Electronic Acre Meter Kit - Optional - Landoll BRILLION SL Series Operator's Manual

Electronic Acre Meter Kit -
Optional
IMPORTANT
Acre Meter is dust and splash resistant, under no
circumstances should this unit be submerged in any
conductive, corrosive, or flammable liquid. At no
time use high pressure water or air to clean it, as this
can damage the unit.
Settings for Loup Acre Meters
The battery operated Acre Meter operates in one of two
modes.
1. In sleep mode, the display is blank, and the counter
is accumulating acres. Sleep mode will be entered if
a button is not pressed for 20 seconds.
2. In entry mode, the display is on, and the operator can
enter values. To get into entry mode, press the
*
/FUNC button. If you continue to press the
button, the acre counter will cycle through the
functions that it can perform. The LEDs above the
display indicate which function is selected.
The available functions are:
Field Acres, Total Acres, Pulses per 400 feet, Width,
Password and Low Battery
Field Acres
*
Press the /FUNC button until the "FIELD" LED is lit.
The digits indicate the acres covered since the field acre
counter was cleared.
To clear the field acre count, press the UP and DOWN
buttons simultaneously for two seconds. If a password
has been entered, you will not be able to clear the total
acre count. Field acres will count in tenths of an acre up
to 9999.9 acres.
Total Acres
*
Press the /FUNC button until the "FIELD" and "TOTAL"
LEDs are lit. The digits indicate the acres covered since
the total acre counter was cleared.
To clear the total acre count, press and hold the UP and
DOWN buttons for two seconds. If a password has been
entered, you will not be able to clear the total acre count.
Total acres will count from.1 to 99999 acres.
Pulses Per 400 Feet
*
Press the /FUNC button until the "PULSES" LED is lit.
The number in the display indicates how many pulses are
generated for every 400 feet driven. There are two
methods to enter the pulses per 400 feet:
1. If you know the number, select it using the UP and
DOWN buttons. When you press the
button, the Acre Counter will accept the number in
the display as the new pulses per 400 feet. See
Table 3-1.
2. If you do not know the pulses per 400 feet, press and
hold the UP and DOWN buttons until the "0" appears
in the display. The "PULSES" LED will blink. The
acre counter is now counting shaft rotations. Enter
the cab and drive 400 feet. Press the
to wake up the acre counter. The "PULSES" LED will
light. The number displayed is the pulses per 400
feet. Press the
If a password is set, you will not be able to adjust the
pulses.
Width
*
Press the
The number displayed is the length of your implement in
feet.
*
/FUNC
To adjust the width, press the UP and DOWN buttons. If
a password has been entered, you will not be able to
adjust the width.
The width can be adjusted from .1 to 99.9 feet, in tenths
of a foot.
Password
The password function allows you to protect the total
acre count, pulses per 400 feet, and width settings with a
password. This stops anyone from accidentally changing
those settings. When the acre counter is shipped, the
password is disabled. You can modify the pulses per 400
feet and implement width at any time.
*
Press the
digits will display the word "Ent" or "dIS".
If the display shows "dIS". The password is disabled.
The total acre count, pulses/400 feet, width, and
password settings can be adjusted using the UP and
DOWN buttons. The password can also be changed
using the UP and DOWN buttons.
If the display shows "Ent": You must enter your password
using the UP and DOWN buttons. When your password
is displayed, press the
password. If the password is correct, you will be able to
change the acre counter settings. The password will be
viewable until the acre counter powers down. When the
acre counter is powered up again, you will have to
re-enter the password to change settings.
If the password is correct, you will be able to change the
acre counter settings. The password will be viewable
until the acre counter powers down. When the acre
counter is powered up again, you will have to re-enter the
password to change settings.
*
/FUNC button to accept the setting.
/FUNC button until the "WIDTH" LED is lit.
/FUNC button until the "PASS" LED is lit. The
*
/FUNC button to test the
OPERATION
*
/FUNC
*
/FUNC button
3-7