Specifications - SMC Networks PSE300A Series Manual

PSE300A
Series
Specifi cations
Series
Applicable SMC
pressure sensor
Rated pressure range
Display/Set pressure range
Display/Smallest settable increment
Power supply voltage
Current consumption
Protection
Display accuracy
Repeatability
Analogue output accuracy (To display value)
Analogue output linearity
Temperature characteristics
Output type
Output mode
Switch operation
Max. load current
Max. applied voltage (NPN only)
Internal voltage drop (Residual voltage)
Delay time ∗
1
Hysteresis mode
Hysteresis
Window comparator mode
Protection
Output type ∗
3
Voltage
output
Output impedance
Output type ∗
3
Current
output
Load impedance
Analogue response time
Input type
Input mode
Input time
Input type
Number of inputs
Connection method
Protection
Unit ∗
4
Display type
Number of screens
Display colour
Number of display digits
Indicator light
Digital fi lter ∗ ∗
5, 6
Enclosure
Withstand voltage
Insulation resistance
Operating temperature range
Operating humidity range
Standards
Body
Lead wire with connector
∗1 Value without digital fi lter (at 0 ms)
∗2 If the sensor input fl uctuates around the set value, the hysteresis must be set to a value more than the amount of fl uctuation, or chattering will occur.
∗3 If the connected sensor does not have an extended analogue output range, there is no extended analogue output range available for this product.
∗4 This setting is only possible for models with the unit selection function. Only MPa, kPa, or Pa is available for models without this function (set by pressure range).
∗5 The response time indicates when the set value is 90 % in relation to the step input.
∗6 Display, switch output and analogue response time are affected.
∗ Products with tiny scratches, marks, or display colour or brightness variations which do not affect the performance of the product are verifi ed as conforming products.
5
PSE533
PSE531
PSE543
PSE550 PSE541
PSE563
PSE561
PSE573
0 to 2 kPa -101 to 0 kPa -100 to 100 kPa 0 to 100 kPa 0 to 500 kPa 0 to 1 MPa
-0.2 to 2.1 kPa -105 to 10 kPa -105 to 105 kPa -10 to 105 kPa -50 to 525 kPa -0.105 to 1.05 MPa -0.105 to 2.1 MPa -0.25 to 5.25 MPa -0.50 to 10.5 MPa
0.001 kPa 0.1 kPa 0.1 kPa
Select from Hysteresis, Window comparator, Error output, or Switch output OFF modes.
NPN: 1 V or less (at load current of 80 mA) PNP: 1.5 V or less (at load current of 80 mA)
1.5 ms or less (with anti-chattering function: 20, 100, 500, 1000, 2000, 5000 ms)
Voltage output: 1 to 5 V Extension analogue output range: 0.6 to 1 V
Current output: 4 to 20 mA Extension analogue output range: 2.4 to 4 mA
Maximum load impedance at power supply voltage of 12 V: 300 Ω
PSE30 A: Voltage input 1 to 5 VDC (Input impedance: 1 MΩ)
PSE31 A: Current input 4 to 20 mA DC (Input impedance: 51 Ω)
MPa, kPa, Pa, kgf/cm
2) Sub screen: 4 digits (Upper 1 digit 11 segments, 7 segments for other)
Lights up when switch output is turned ON. OUT1, OUT2: Orange
50 MΩ or more (500 VDC measured via megohmmeter) between terminals and housing
Operating: 0 to 50 °C, Stored: -10 to 60 °C (No freezing or condensation)
UL/CSA (E216656), CE marking (EMC Directive, RoHS Directive)
For pressure switch precautions and specifi c product precautions,
refer to the "Operation Manual" on the SMC website.
PSE300A
PSE564
PSE532
PSE574
0.1 kPa 1 kPa
12 to 24 VDC ±10 %, Ripple (p-p) 10 % or less
35 mA or less
Polarity protection
±0.5 % F.S. ±1 digit (Ambient temperature of 25 °C)
±0.1 % F.S. ±1 digit
±0.5 % F.S.
±0.2 % F.S.
±0.5 % F.S. (Reference: 25 °C)
Select from NPN or PNP open collector 2 outputs.
Select from Normal or Reversed output.
80 mA
30 VDC
Variable from 0 ∗
Over current protection
Approx. 1 kΩ
at power supply voltage of 24 V: 600 Ω
Minimum load impedance: 50 Ω
50 ms or less
Non-voltage input: 0.4 V or less
Select from Auto-shift or Auto-shift zero.
5 ms or more
1 input
Connector (e-CON)
Over voltage protection (up to a voltage of 26.4 V)
2
, bar, mbar, psi, inHg, mmHg, mmH
LCD
3-screen display (Main screen, Sub screen x 2)
1) Main screen: Red/Green
2) Sub screen: Orange
1) Main screen: 4 digits (7 segments)
0, 10, 50, 100, 500, 1000, 5000 ms
IP40
1000 VAC for 1 minute between terminals and housing
Operating/Stored: 35 to 85 % RH (No condensation)
25 g (Excludes power supply and output lead wires)
+39 g
PSE530
PSE540
PSE575 PSE576
PSE560
PSE570
0 to 2 MPa 0 to 5 MPa 0 to 10 MPa
0.001 MPa 0.001 MPa 0.01 MPa
2
O
2
PSE577
0.01 MPa