Advertisement
Main
Sub
code
code
66
33
Signal detection check
Used to detect signals and display the result with ON/OFF.
Sim66-33 SIGNAL CHK
1:CI FNET
2:CNG CED BT DT
3:Flag SDT DTMF
(1 - 3)
Sim66-33 SIGNAL CHK
CI :
FNET:
Sim66-33 SIGNAL CHK
CI :OFF FNET:OFF
DETECT
SIM66-33 initial window
34
Communication time measurement
Used to perform a send/receive test and measure and display the time required for send/receive of the
image data in the communication.
37
Speaker sound volume adjustment
Used to adjust the speaker sound volume.
During execution of this simulation, the following test sound is sent to the line and the speaker.
The send level to the line is set to the soft SW setting value.
The speaker sound volume can be adjusted by the operation.
The type of sound can be selected among the following:
1.Call sound, 2.Line monitor sound, 3.On-hook, 4.Terminating sound, 5.Communication end sound,
6.DTMF send sound
For each type of sound, the sound volume can be selected among the following:
No sound, Small, Medium, Large
The set value is written into each soft SW.
Type of sound
1.Call sound
2.Line monitor sound
3.On-hook
4.Terminating sound
5.Communication end sound Communication end
6.DTMF send sound
[CA] key
[INTERRUPT] key : Sub code input window
[C] key
Numeric key
[ON] key
X
[START] key
After selection with numeric key
[OK] key
1:CI FINET
Sim66-33 SIGNAL CHK
Signal detection
CNG :
CED :
YES/NO is displayed
BT :
DT :
with ON/OFF.
EXEC
After pressing [OK] key,
during execution
[OK] key
Sim66-33 SIGNAL CHK
CNG :OFF
BT :OFF
EXEC
DETECT
[BACK] key
SIM66-33 initial window
Immediately after
pressing [OK] key, the
Sim66-34 COMM. TIME
window shifts to the
next one.
[OK] key
EXEC
[CA] key
: Simulation cancel
[INTERRUPT] key : Sub code input window
[OK] key
: Settlement
[BACK] key
: Simulation code input window
[START] key
: Settlement
[C] key
: Disable
Test sound
Call sound
Communication signal
sound (33600bps)
Communication signal
sound (33600bps)
Read end sound
sound
DTMF send sound
MX-M182 SIMULATIONS 7-58
Contents
: Simulation cancel
: Input clear
: Item selection
: Input value settlement and execution
: Similar to OK key
2:CNG CED BT DT
Sim66-33 SIGNAL CHK
Signal detection
Flag:
SDT :
YES/NO is displayed
DTMF:
with ON/OFF.
EXEC
After pressing [OK] key,
during execution
[OK] key
Sim66-33 SIGNAL CHK
Flag:OFF SDT :OFF
CED :OFF
DTMF:OFF
DT :OFF
DETECT
EXEC
[BACK] key
SIM66-33 initial window
Sim66-34 COMM. TIME
COMM. TIME:
xxx:xx:xx:xxxms
[BACK] key
Sound volume setting value
0
1
No Sound
Small
No Sound
Small
Setting
Small
disable
No Sound
Small
No Sound
Small
No Sound
Small
3:Flag SDT DTMF
Signal detection
YES/NO is displayed
with ON/OFF.
EXEC
After pressing [OK] key,
during execution
[OK] key
EXEC
[BACK] key
Simulation code
input window
2
3
Medium
Large
Medium
Large
Medium
Large
Medium
Large
Medium
Large
Medium
Large
Remark
Advertisement
